EZ Roof Mount Attachments EZ Roof Mount Attachments With L-Foot, Standoffs and Variants Pub.
EZ Roof Mount Attachments Please read carefully before installing Patent # US8122648B SunModo’s EZ Roof Mount Attachments can be used to mount PV panels on pitch roofs. All installations shall be in accordance with NEC requirements in the USA. Table of Contents Installer Responsibility: .......................................................................................................................... 3 Safety: ........................................................................................
EZ Roof Mount Attachments Installer Responsibility: Before ordering and installing materials, all system layout dimensions should be confirmed by field measurements. SunModo reserves the right to alter, without notice, any details, proposals or plans. Any inquiries that you may have concerning installation of the PV system should be directed to your SunModo Sales representative. Consult SunModo Sales for any information not contained in this manual.
EZ Roof Mount Attachments EZ Roof Mount Series: EZ Roof Mount Kit includes: Flashing L-Foot Roof Shoe and Gasket 4” Lag Bolt AL Hex Cap 3/8” Flange Nut and Bolt K10068-XXX EZ Roof Mount with L-Foot (-001 as shown) EZ Roof Mount Decking Kit: Flashing L-Foot Roof Shoe and Gasket 4X 1/4 X 3” Decking Screw AL Hex Cap 3/8” Flange Nut and Bolt K10068-B20 EZ Roof Mount with L-Foot (Black as shown) EZ Roof Mount Standoff Kit: Flashing Roof Shoe and Gasket 4” Lag Bolt AL He
EZ Roof Mount Attachments Primary Materials: Aluminum Flashings are offered in two sizes: 10”X12.5” and 18”X18”. Available in clear, black and brown anodize. A20052-XXX AL Flashing Aluminum L-Foot is offered in clear, black and brown. A20064-XXX AL L-Foot AL Hex Cap Available in clear and black A20066-001 and -BK1 AL Hex Cap Aluminum Shoe is provided with EPDM Sealing Washer installed. A20065-001 AL Shoe C10006-001 Sealing Washer 5/16 Stainless Steel Lag Bolts are available lengths: 3.5”, 4”, 4.
EZ Roof Mount Attachments Aluminum Standoff heights: 2”, 3”, 5” and 7” (part of EZ Roof Kit K10070-XXX) A20049-XXX Standoff (multiple lengths) Aluminum C-Bracket (part of EZ Roof Kit K12005-001) A22001-001 C-Bracket Conduit Clamp for 3/4” and 1” diameter conduit Conduit Mount L-Foot Helio Rails: Features both 1/4” and 3/8” side slots, and 1/4” top slot for clamping PV panels. Available in 84”, 124”, 164” and 206” lengths. Last 3 digits denote rail length. 4 stock sizes in clear and black.
EZ Roof Mount Attachments HR150 (Open Rail): Features wire management channel and both 1/4” and 3/8” side slots, and 1/4” top slot for clamping PV panels. Available in 84”, 124”, 164” and 206” lengths. Last 3 digits denote rail length. 4 stock sizes in clear and black. A20242-XXX (Clear) A20242-XXX-BK (Black) HR150 (Open Rail) 1/4” Slot Open Rail Splice Kit with 4X 1/4-20 Bolts and Flange Nuts with integral grounding. May be repositioned until torqued to final value.
EZ Roof Mount Attachments Tools Required for Installation: Electric Drill or impact driver. Note that the use of an impact driver is strongly discouraged for all stainless nut and bolt hardware. Roofing Bar Drill Bit for lag bolts, pilot hole 7/32” diameter for 5/16” lag bolt 3/8” Socket Wrench Sockets for 3/8” drive sockets, 7/16”, 1/2”, 9/16” and 1-1/16” Torque Wrench 3/8” drive, 0 to 35 ft. lbs. Anti-seize compound (Permatex 80071 or equivalent).
EZ Roof Mount Attachments Caulk gun and silicon sealant ChemLink M1 (or equivalent) for wood and composite roofs. ChemLink DuraLink (or equivalent) for metal roofs. Tape measure Saws for cutting aluminum posts and rails as necessary Other items that can be useful: Chalk or roofer’s marker to layout roof. Adaptor for 3/8” socket to drill chuck. #3 Phillips bit Torque Values: These values must be adhered to for mechanical strength.
EZ Roof Mount Attachments Flashing Placement: If cutting the shingle to reposition the flashing proves to be impractical, apply sealant around the edges of the flashing to prevent debris from accumulating under the shingle.
EZ Roof Mount Attachments Installation Instructions: EZ Roof Mount Kit K10068-XXX 1. From the marked location, move down the roof 2-1/4” from the bottom of the shingle, and drill the pilot hole for the Lag Bolt with a 7/32” drill bit. For maximum strength, the hole should not be more than 3” in depth, and a drill stop may be used to insure this. 1 2. Clean sawdust, and fill hole with sealant, such as Chemlink M1 for wood and composite roofs, or ChemLink DuraLink for metal roofs.
EZ Roof Mount Attachments Installation Instructions EZ Roof Mounting Standoff Kit K10070-XXX Mount the AL Shoe using steps 1-3 (shown above). A. Place AL Standoff on AL Shoe threads and tighten by hand, then by wrench. Use 15 ft.-lbs. nominal torque. A B. Using the 3/8” Flange Bolt (supplied with AL L-Foot) attach to the top of the Standoff. B C. Install AL Rail to L-Foot to the specific orientation. Then, tighten 3/8” Flange Nut to 15 ft-lbs. and Hex Cap to 15 ft-lbs. torque.
EZ Roof Mount Attachments Optional Mounting Instructions: EZ Roof Mount Kit K10068-B20 1. From the desired location, move down the roof 2-1/4” from the bottom of the shingle, and locate the EZ Roof Mount AL Shoe center. The AL Shoe will be used as a template to locate the 4 screws. 2. Place a bead of Chem-link M1 for wood and composite roofs along the length of the screw four (4) 1/4” X 3” selfdrilling Decking Screws. Mount the AL Shoe to the roof through the shingles using the four Decking Screws.
EZ Roof Mount Attachments See www.sunmodo.com for current warranty documents and information.