User manual

120
Program description - Control adjust | Winged models
0%
0%
0%
–––
0%
–––
–––
GL
GL
GL
GL
normal
fr
fr
fr
3
2
In5
offset
In6
In7
In8
typ
Erasing a transmitter control or switch assign-
ment
A simultaneous tap on the  or  keys of the
right four-way button (CLEAR) while on an input line
with an active transmitter control or switch assign-
ment – see above figures – will reset the given input
back to “fr” and “---”.
Tips:
• When assigning switches, pay attention to the de-
sired switching direction and also that all unused
inputs remain “free” or are again reset to “free”.
This is necessary to ensure that inadvertent actu-
ations of these unused controls cannot cause mal-
functions.
• The travel setting described below allows the ap-
propriate end state to be established for an as-
signed switch.
Column 4, “offset”
The control center for the given control, i. e. its zero
point, can be changed in this column. The adjustment
range lies between -125 % and +125 %.
0%
0%
0%
–––
0%
–––
–––
GL
GL
GL
GL
nor mal
fr
fr
fr
3
2
In5
offset
In6
In7
In8
typ
A simultaneous tap on the  or  keys of the
right four-way button (CLEAR) will reset the entry
field value displayed in inverse video back to “0 %”.
Column 5, “– travel +”
The “-Travel+” column is accessed by using the Select
button  of the left or right-hand four-way button to
shift the marker frame to the right, beyond the “Offset”
column, as indicated by the right-pointing arrow at
bottom left of the screen.
This column is used to set servo travel symmetrically
or asymmetrically for each side. The setting range is
±125 % of normal servo travel.
Select an input, 5 through 8 or 5 through 12, with the
 selection keys of the left or right four-way button.
To set symmetric travel, i. e. control-side independent
travel, the respective operating element (transmitter
control or switch) is to be put into a position in which
the travel setting will be covered on both sides by the
marker frame:
– travel +
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
normal
In5
In6
In7
In8
To set asymmetric travel, the respective operating
element (transmitter control or switch) is to be moved
to the side to be set such that the marker frame only
includes the value to be changed:
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
normal
– travel +
In5
In6
In7
In8
The value setting is activated by briefly touching the
center SET key of the right four-way button. The value
field/s will be displayed in inverse video. Values can
be changed with the selection keys of the right four-
way button:
+100%
+100%
+100%
+100%
+100%
+100%
normal
+111%
+111%
– travel +
In5
In6
In7
In8
+100%
+100%
+100%
+100%
+100%
+100%
+100%
normal
+88%
– travel +
In5
In6
In7
In8
Another brief tap on the center SET key of the right
four-way button will complete the entry.
Negative and positive parameter values are possible
in order to appropriately adapt the control’s direction
or effect.
A simultaneous tap on the  or  keys of the
right four-way button (CLEAR) will reset the changed
parameter displayed in inverse video back to
“+100 %”.
Important:
In contrast to servo travel settings, changing the con-
trol travel setting affects all “downstream” mixer and
coupling inputs, i. e. any and all servos actuated by
the given transmitter control.
Column 6, “– time +”
Each of the function inputs 5 … 8 or 5 … 12 can be
assigned a symmetrical or asymmetric time delay of
between 0 and 9.9 s.
Move the marker frame to the right beyond the co-
lumn labeled “– travel +” with the  selection key of
the left or right four-way button.