User manual

124
Program description - Control adjust | Helicopter models
0%
–––GL
normal
fr
SEL
In5
offset
typ
Move desired switch
to ON position
(ext. switch: SET)
Actuate the desired toggle switch from its “OFF” to its
“ON” position or, for a 3-way switch, beginning from
its middle position, assign a switch direction – prefer-
ably the “second” direction. This means, if a function
is to be switched on by moving the switch forward two
positions, i. e. away from the pilot, then begin from the
switch’s middle position and move the switch away
from the pilot.
The display will then present the switch number to-
gether with a symbol indicating the given switch direc-
tion. At the same time, the column label in the footer
line will change from SEL into another switch symbol:
0%
0%
0%
–––
0%
Gyro
Lim.
–––
–––
–––
GL
GL
GL
GL
normal
fr
fr
3
In5
offset
Thro
typ
Lv2
Now put the 3-way switch back into its middle posi-
tion. Move the marker frame as necessary to the left
into the column labeled with the new switch symbol,
briefly tap on the center SET key of the right four-way
button then assign the switch’s other switch direction
by once again starting from the middle position but
this time move the switch in the other direction.
The display will now present the given switch number
together with a symbol indicating the given switch
direction, for example:
0%
0%
0%
0%
Gyro
Lim.
–––
–––
–––
GL
GL
GL
GL
normal
fr
fr
3
2
In5
offset
Thro
typ
Lv2
Erasing a transmitter control or switch assign-
ment
A simultaneous tap on the  or  keys of the
right four-way button (CLEAR) while on an input line
with an active transmitter control or switch assign-
ment – see above figures – will reset the given input
back to “fr” and “---”.
Tips:
• When assigning switches, pay attention to the de-
sired switching direction and also that all unused
inputs remain “free” or are again reset to “free”.
This is necessary to ensure that inadvertent actu-
ations of these unused controls cannot cause mal-
functions.
• The travel setting described below allows the ap-
propriate end state to be established for an as-
signed switch.
Column 4, “Offset”
The control center for the given control, i. e. its zero
point, can be changed in this column. The adjustment
range lies between -125 % and +125 %.
0%
0%
0%
0%
Gyro
Lim.
–––
–––
–––
GL
GL
GL
GL
normal
fr
fr
3
2
In5
offset
Thro
typ
Lv2
A simultaneous tap on the  or  keys of the
right four-way button (CLEAR) will reset the entry
field value displayed in inverse video back to “0 %”.
Column 5, “– travel +”
The “- travel +” column is accessed by using the
Select button  of the left or right-hand four-way
button to shift the marker frame to the right, beyond
the “Offset” column, as indicated by the right-pointing
arrow at bottom left of the screen.
This column is used to set servo travel symmetrically
or asymmetrically for each side. The setting range is
±125 % of normal servo travel.
Select an input, In5, Thro, Gyro or Lim. or In5, Thro,
Gyro, In8 through 11 or Lim., with the  selection
keys of the left or right four-way button.
To set symmetric travel, i. e. control-side independent
travel, the respective operating element (transmitter
control or switch) is to be put into a position in which
the travel setting will be covered on both sides by the
marker frame:
– travel +
+100%
+100%
+100%
+100%
Gyro
Lim.
+100%
+100%
+100%
+100%
normal
In5
Thro
To set asymmetric travel, the respective operating
element (transmitter control or switch) is to be moved
to the side to be set such that the marker frame only
includes the value to be changed:
+100%
+100%
+100%
+100%
Gyro
Lim.
+100%
+100%
+100%
+100%
normal
– travel +
In5
Thro
The value setting is activated by briefly touching the
center SET key of the right four-way button. The value