User manual
259Program description - Multichannel
INPUT2
INPUT3
Multichannel 1
SEL offset
INPUT1
INPUT4
–––
0%
––– 0%
––– 0%
––– 0%
fr
fr
fr
fr
… and „MC2“ (Multichannel 2) …
INPUT2
INPUT3
Multichannel 2
SEL offset
INPUT1
INPUT4
–––
0%
––– 0%
––– 0%
––– 0%
INPUT5 ––– 0%
INPUT6
––– 0%
INPUT7
––– 0%
INPUT8
––– 0%
fr
fr
fr
fr
fr
fr
fr
fr
Column 2 “Control”
INPUT2
INPUT3
Multichannel 1
SEL offset
INPUT1
INPUT4
–––
0%
––– 0%
––– 0%
––– 0%
fr
fr
fr
fr
Use the arrow keys to move to the column over SEL.
After completing the activation of transmitter control
assignment by tapping the center SET key of the right
four-way button, the message shown below will ap-
pear in the display:
IN
IN
Multichannel 1
SEL offset
IN
INPUT4
0%
0%
0%
––– 0%
fr
Move desired
control adj.
Erasing transmitter controls or switches
With transmitter control / switch assignment active,
simultaneously pressing the or buttons of
the right-hand four-way button (CLEAR) – see screen-
shots above – resets the corresponding input to “fr”
and “---”.
Column 4 “offset”
INPUT2
INPUT3
Multichannel 1
offset
INPUT1
INPUT4
0%
––– 0%
––– 0%
––– 0%
fr
fr
fr
2
3
The control center for the given control, i. e. its zero
point, can be changed in this column. The adjustment
range lies between -100 % and +100 %.
Simultaneously tapping on the or keys of
the right four-way button (CLEAR) will reset the value
displayed in inverse video back to its “0 %” value.
Note:
Leave the offset setting at 0 % while making switch
assignments.
Column 5 „– travel +“
To adjust servo travel, move to the right, beyond the
“Offset” column, following the right-pointing arrow in
the bottom left-hand corner of the screen:
INPUT2
INPUT3
Multichannel 1
– travel +
INPUT1
INPUT4
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
Finally, transmitter control travel is set for both sides
in the column “-travel+”. The range for this lies be-
tween -100 % and +100 %. This is accomplished by
Now operate the transmitter control you wish to use:
the information window closes, and instead the Value
field displays the name of the transmitter control you
have chosen.
Note:
If you are using the Nautic-Expert switch module,
Order No. 4159, any proportional controls you assign
act like switches when close to their end-points.
Column 3 “Switch”
Multichannel 1
SEL offset
INPUT4
––– 0%
fr
Move desired switch
to ON position
(ext. switch: SET)
This column is used to assign each of the inputs
used, 1 through 8 (maximum), to any switch available
on the transmitter. These assignments are done as
described in the section „Physical control, switch and
control switch assignments“ on page 68:
Any controls which were previously assigned in the
second column will be erased. In this case, instead of
SEL, the switch symbol
will be displayed at the
bottom of the 2nd column such that now a second
“normal” switch, or even a transmitter control switch,
logical switch, … can be assigned as needed from
the group of “expanded switches”. In general it is suf-
ficient to assign a simple switch or transmitter control.
INPUT2
INPUT3
Multichannel 1
offset
INPUT1
INPUT4
–––
0%
––– 0%
––– 0%
––– 0%
fr
fr
fr
2