User manual

269Program description - Basic settings
–––
–––
–––
SEL
SEL
Basic settings
Va
Be
Vo
Own
Move desired
control adj.
Now move the desired control, for example, the right
proportional slider Sl2. Afterward, this slider can be
used anytime to incrementally regulate volume for the
selected group between 0 and 10.
Following a simultaneous tap on the  or  keys
of the right four-way button (CLEAR), the display will
return to its “fr” default value.
via three position switch
Use the selection keys on the left or right four-way
button to move the marker frame to the column above
the switch symbol at the display’s lower edge then
briefly tap the center SET key of the right four-way
button. The message shown below will then appear in
the display:
SEL
SEL
Basic settings
Own
Move desired switch
to ON position
(ext. switch: SET)
Now, assign a switch as described in the section
“Physical control, switch and control switch assign-
ments” on page 68. Ideally a self-neutralizing three
position switch, e. g. like that offered by Graupner
under order no. 33001.5. Afterward, this switch can be
used anytime to incrementally regulate volume for the
selected group between 0 and 10.
Following a simultaneous tap on the  or  keys
of the right four-way button (CLEAR), the display will
return to its “---” default value.
Own(er)
–––7
3
–––7
Cn5
Cn6
Basic settings
Vario Vol
Beeps Vol
Voice Vol
Own
2
3
Up to 15 characters can be used to specify the own-
er’s name. Change to the next screen page ( ) with
a brief tap on the center SET key of the right four-way
button:
!"#$%&’()�+,–./0123
456789:;
Owner
H-J Sandb
FGHIJKLMNOPQRSTUVWX
YZ[¥]^_`ab cdefghijk
?@ AB CDE
Select the desired characters with the selection keys
of the left four-way button. With a brief tap on the 
selection key of the right four-way button or its center
SET key, move to the next position in which a charac-
ter can be selected. A simultaneous tap on the 
or  keys of the right four-way button (CLEAR) will
place a space character at the current position.
Positioning to any character position within the en-
try field can be done with the  keys of the right
touch pad.
A brief tap on the center ESC key of the left four-way
button will cause a return to the previous menu page.
(Pre-set) Stick mode
As a basic principle, there are four different ways to
assign the four control functions, aileron, elevator,
rudder and throttle or brake flaps for winged models
as well as rolling, pitching, tail rotor and throttle/pitch
for helicopter models to the two sticks. Just which of
these options is chosen depends on the individual
preferences of the individual model pilot:
Winged model stick mode
MODE 2 (Throttle at left stick)
elev. down
elev. up
left rudder
right rudder
full throttle
idle
left aileron
right aileron
full throttle
idle
left rudder
right rudder
elev. down
elev. up
left aileron
right aileron
elev. down
elev. up
left aileron
right aileron
full throttle
idle
left rudder
right rudder
full throttle
idle
left aileron
right aileron
elev. down
elev. up
left rudder
right rudder
MODE 1 (Throttle at rigth stick)
MODE 3 (Throttle at right stick)
MODE 4 (Throttle at left stick)
Helicopter model stick mode
MODE 2 (Throttle at left stick)
pitch axis
pitch axis
tail rotor
tail rotor
throttle/pitch
throttle/pitch
roll
roll
throttle/pitch
throttle/pitch
tail rotor
tail rotor
pitch axis
pitch axis
roll
roll
pitch axis
pitch axis
roll
roll
throttle/pitch
throttle/pitch
tail rotor
tail rotor
throttle/pitch
throttle/pitch
roll
roll
pitch axis
pitch axis
tail rotor
tail rotor
MODE 1 (Throttle at right stick)
MODE 3 (Throttle at right stick)
MODE 4 (Throttle at left stick)
Use the  selection keys of the left or right four-
way button to select the “Stick mode” line. The option
field will be framed.