User manual

299Programming examples - Using flight phases
2
nd
Step
In order to actually be able to switch between the indi-
vidual flight phases, the assignment of one or multiple
switches is necessary. Either one of the two three-
way switches is ideally suited for switching between
up to three flight phases.
Each of the two switch end positions starting from the
center position will be assigned to one of the flight
phase switches A … F. The assignment of the switch
takes place in the menu …
»Phase assignment« (page 158)
First select “C” with the marker frame. Then briefly
tap on the center SET key of the right four-way button
and move the switch from its center position to one of
its end-positions, for example, forward:
Phase assignment
A B
C D E F
1 normal
6
prior
combi
Move the switch back to the center position and then
select “D”, and after activation of the switch assign-
ment, move the switch to the other limit position, for
example, back:
A B
C D E F
1 normal
6
5
Phase assignment
prior
combi
Now the 3-way switch is programmed.
Now and additional switch could be assigned for the
“start” flight phase, if applicable. In this case under
“A”, so that the “start” phase is always switched to
from every other flight phase in parallel to the switch-
ing-on of the motor:
A B
C D E F
1 normal
7
6
5
Phase assignment
prior
combi
The given switch positions must then be assigned
to respective flight phases (names). Although some
flight phases have already been assigned to names,
the phase name «1 Normal» will always initially ap-
pear at the right in the display; see the figures above.
First move the 3-way switch to one of its limit posi-
tions, for example to the back, and switch with the
marker frame in the display down to the right to set
the flight phase name. Briefly tap on the center SET
key of the right four-way button to activate the en-
try field then select the desired flight phase for this
switch position, in this example «2 Thermal», with the
selection keys:
A B
C D E F
6
5
2 Thermal
7
Phase assignment
prior
combi
Proceed in the same manner for the other switch limit
position, which is assigned the name “3 Speed”.
If applicable move Switch 2 and assign this switch
combination the name “4 Start”.
A brief tap on the center ESC of the left four-way but-
ton or the center SET key of the right four-way button
will complete the phase name assignment.
The flight-phase dependent model settings made
before the assignment of phase switches are now in
the flight phase «1 Normal». This is the phase which
is called with the open «Start» switch in the center
position of the 3-way switch.
3
rd
Step
In order to not have to carry out all previously made
settings for the model in the “new” flight phase from
the ground up, we recommend first copying the al-
ready tested programming of the flight phase “Nor-
mal” to the other flight phases. This is carried out in
the menu …
»Copy / Erase« (page 80)
=>
=>
=>
=>
=>
=>
=>
Copy flight phase
Erase model
Copy model–>model
Export to SD
Import from SD
Here, select the “Copy flight phase” menu item with
the selection keys then briefly tap the center SET key
of the right four-way button.
In the window which now appears, “Copy from
phase”, “1 Normal” is selected …
7
Copy from phase:
3
5
2
4
6
1
normal Thermal
Speed Launch
… and a subsequent brief tap on the center SET key
of the right four-way button will change the display
to “Copy to phase”. Now the target is to be selected
(initially “2 Thermal”) and confirmed by another tap on
the center SET key of the right four-way button. After
confirmation of the subsequent safety query, all set-
tings are copied according to the selection.
Proceed in the same manner with the other two
phases (“1 Normal” to “3 Speed” and “1 Normal” to
“4 Start”).