User manual

39Transmitter description - Telemetry data display
by simply waiting until, after a brief pause, the main
display of the given selected sensor appears auto-
matically.
Notes:
• The sequence of the below described displays is
a consequence – starting from the given main dis-
play – of taps on the  key.
• More details about the following named modules
can be found in the appendix and in Internet at
www.graupner.de in the web page for the given
product.
RECEIVER
RX–S QUA: 100%
RX–S STR: 100%
TX–dBm: –33dBm
RX–dBm: –33dBm
RX–VOLT:4.8V TMP
L–PACK: 10ms
R–LOW V:4.6V +22°C
This screen presents the »RX DATAVIEW« of the
»Telemetry« menu’s »SETTING & DATAVIEW«
sub-menu, see page 241, with data processed and
displayed graphically.
The displayed items are as follows:
Value Explanation
RX-S QUA signal quality in %
RX-S STR signal strength in %
RX-dBm Reception power in dBm
TX-dBm transmit power in dBm
L-PACK Indicates the longest time span in ms
in which data packages are lost in the
transmission from the transmitter to the
receiver.
RX-VOLT current operating voltage of the
receiver's power supply in volts
R-LOW V Lowest receiver operating voltage since
last startup, in volts
TMP the thermometer depicts the receiver's
current operating temperature
GENERAL MODUL
ELECT. AIR
VARIO
GPS
RECEIVER
AIR ESC
GENERAL
0.0V
BAT1
BAT2
0.0V T2 0°C
T1 0°C
E FUEL F
CELL.V
1:0.00
2:0.00
3:0.00
4:0.00
5:0.00
6:0.00
0
0.0V
BAT1
BAT2
0.0V T2 0°C
T1 0°C
E FUEL F
ALT
0m
0m1
0m3
0.0A
POWER
0.0V
0
If attached to the receiver, this screen will display the
data acquired by a General-Engine module, order
no. 33610, or a General-Air module, order no. 33611.
More details about these modules can be found in
the appendix or in Internet at www.graupner.de in the
web page for the given product.
Depending on how this module is equipped with sen-
sors, this screen can permanently display the data
shown in the table below.
The current voltage of up to two batteries (BAT1 and
BAT2), the measurement results of up to two tem-
perature sensors (T1 and T2) and a fill level gage for
the fuel tank.
An alternating display along the screen’s right edge
will display a list of current cell voltages for a LiPo
battery with up to six cells or operational data (current
altitude with respect to the starting location, ascent/
decent m/1 s and m/3 s, current current being drawn
in amperes and current voltage of the battery con-
nected to the sensor).
The displayed items are as follows:
Value Explanation
BAT1 /
BAT2
battery 1 or 2
FUEL fuel level / tank gage
E / F empty / full
T1 / T2 temperature of sensor 1 or 2
CELL V cell voltage of cells 1 … max. 6
ALT current altitude
0m1 m/1 s ascent/decent rate
0m3 m/3 s ascent/decent rate
A current draw in amperes
V battery voltage
Battery and load indicators
0.0V
0.0A
0mAh
0ml
This display depicts current voltage, current cur-
rent draw and, if attached, the expended capacity
of “Batt 1” connected to the General-Engine module
(order no. 33610) or General-Air (order no. 33611)