User's Manual

124
Detail program description - Control adjust
SEL
0%
0%
0%
C1
C2
C3
–––
C4
CONTROL SWITCH
0%
STO
–––
–––
–––
Ct6
Resetting a control switch back to "free"
To reset a control switch back to "free", make sure the
display is as below …
SEL
+75%
0%
0%
G1
G2
C3
–––
C4
CONTROL SWITCH
Gb1
Gb1
–75%
STO
–––
–––
–––
Move desired
control adj.
… and then press the cd or ef keys on the right
touch pad (CLEAR) briefl y to erase the transmitter
control assignment.
Defi ning the switching point
Using the arrow key f on the left or right touch pad,
move the marker frame into the STO (i.e. the STOre)
column.
Move the selected transmitter control to the position at
which the switching point – i. e. the switch between OFF/
ON – should trigger and briefl y tap the center
SET key
on the right touch pad. The current position is displayed,
for example "+85%":
SEL
0%
0%
0%
C1
C2
C3
–––
C4
CONTROL SWITCH
+85%
STO
–––
–––
–––
Ct6
The switching point can be altered at any time by
tapping the center
SET key on the right touch pad again.
Note:
Do not, however, set a switching point at a transmitter
control's travel end-point, since this makes reliable
switching impossible. Where a 3-stage switch (CTRL 9
and 10) is used to operate a control switch you should
therefore program the switching point beforehand using
one of the proportional rotary controls (CTRL 6 to 8):
First, assign the corresponding proportional control in
the 2nd column and set the switching point in such a
way that will ensure the subsequent confi guration for
the 3-stage switch will reliably exceed this value. If you
do not, the switching function will be unreliable, since
the control switch triggers only if a value unambiguously
fails to meet or exceeds the value set! To complete the
procedure, de-assign the transmitter control and then
assign the 3-stage switch.
Setting the switching direction
The switching direction of the control switch is changed
as required in the 4th column. Using the arrow key f on
the left or right touch pad, move the marker frame into
the SEL (i.e. the SELect) column. After briefl y tapping
the center
SET key on the right touch pad, you can then
use the arro
w keys on the left or right touch pad to set
the switching direction from "normal" to "reversed" and
vice versa:
SEL
0%
0%
0%
C1
C2
C3
–––
C4
CONTROL SWITCH
+85%
STO
–––
–––
–––
Ct6
SEL
0%
0%
0%
C1
C2
C3
–––
C4
CONTROL SWITCH
+85%
STO
–––
–––
–––
Ct6
Tapping the cd or ef keys on the right touch pad at
the same time (CLEAR) will reset the switching direction
to "=>".
The current switch position of the control switch is
displayed in the leftmost column by the switch icon next
to the number of the control switch.
Notes:
In this example, control switch "C1" remains open •
while transmitter control 6 (the throttle limiter for
a heli) is at less than +85% of full travel. It closes
once the switching point is exceeded, i.e. by a value
between +85% and the upper travel end-point.
In the above example with the switching direction •
reversed, control switch "C1" remains closed while
the transmitter control is at less than +85% of full
travel. As soon as the switching point is exceeded –
in this example, by a value between +85% and the
upper travel end-point – "C3" opens.