User's Manual

140
Detail program description - Control adjust
Switching between "forwards" and "backwards"
Timer runs forwards (stopwatch function)
Following switch assignment, if the stopwatch shown on
the basic display is started with the initial value of "0:00",
then it will run forwards for max. 180 min and 59 s and
then restart from 0:00.
Timer runs backwards (countdown function)
In the – left – minutes fi eld, select a start time between 0
and 180 min …
Timer
–––12:34h
1:23h
0:00
180:00
SEL
Model time
Batt. time
Top :
Centr:
Stop
Flight
… and in the – right – seconds fi eld, select a start time
between 0 and 59 s (or any combination of these):
Timer
–––12:34h
1:23h
180:59
0:00
SEL
Model time
Batt. time
Top :
Centr:
Stop
Flight
Procedure
Select the desired input fi eld using the arrow keys 1.
ef on the left or right touch pad.
Now tap 2.
SET in the center of the right touch pad.
Mak
e y
our time selection in the highlighted min
utes3.
or seconds field, using the arro
w k
e
ys on the r
ight
touch pad.
Complete your input by tapping the center 4. SET key.
If you tap the 5. cd or ef keys on the right touch
pad at the same time (CLEAR), this will reset any
settings made back to "0" or "00".
After switching back to the basic display (by tapping 6.
the center
ESC key on the left touch pad as many
times as required), mak
e sure the stopwatch is
stopped and then tap the cd or ef keys on
the right touch pad (CLEAR) so that the stopwatch
switches over to the "timer" function. Look to the top
right in the f
ollowing screen image:
GRAUBELE
#01
0:00h
Stop
Flt
K78
10:01
0:00
0.0V
5.9V
M
HoTT
After the assigned switch is activated, the stopwatch
starts at the initial value set and runs backwards
("countdown function"). Once the timer reaches zero it
does not stop, but continues to run to enable you to read
off the time elapsed after it reached 0:00. To make this
absolutely clear, the timer is shown highlighted.
"Alarm" timer
The "Alarm" column is accessed by using the arrow
key f on the left or right touch pad to move the marker
frame over the "Timer column to the right. In the
"Alarm" column, you can defi ne a time between 5 and
90 seconds (in 5-second increments) before zero is
reached: at this point an audible signal will be emitted,
which eliminates the need for you to check the screen
continually during the fl ight.
Alarm
–––
12:34h
1:23h
0s
–––
–––
SEL
0s
Model time
Batt. time
Top :
Centr:
Stop
Flight
If you tap the cd or ef keys on the right touch pad
at the same time (CLEAR), this will reset any settings
made back to "0 s".
Audible signal sequence
30 s before zero: Triple beep
Single beep ev
ery two seconds
20 s before zero: Double beep
Single beep every two seconds
10 s before zero: Single beep
Single beep every second
5 s before zero: Single, higher-frequency beep
every second
Zero: Extended audible signal and
screen switches to highlighted
display
Resetting timers when stopped
Tapping the cd keys on the right touch pad at
the same time (CLEAR) will reset the display of
previously stopped timers on the basic display.
Notes:
Timers that are running backwards are shown on the •
basic display with a fl ashing colon (:) between the
minutes and the seconds fi elds.
A typical application, "Timer activation via the C1 •
joystick", can be found on page 252).