User's Manual

281
Detail program description - Control adjust
change these in the adopted defaults "Stick mode",
"DSC output" and "Pitch front/rear" as well as within
the respective model memory location.
The setting the "Contrast" line determines the legibility
of the display under poor light conditions and the setting
in the "Display light" line determines how long the
display lighting remains illuminated after the transmitter
is switched on or after the last key actuation.
With "Power-on beep yes/no" you determine whether
the transmitter plays a recognition melody when
switching on.
In the "Battery type" line you specify whether the
transmitter is supplied with current from a "NiMH" or a
"LiPo" battery, and in the "Battery warning" line below
it, you determine the voltage at which the low-voltage
warning of the transmitter should trigger. Do not enter a
value that is too low here, so you have enough time to
land your helicopter.
In the "Power-on warn." line you can adjust how long
the transmitter should wait after the last actuation of
an operating element until it alerts you that it is still
switched on with optical and acoustic warning signals.
With the values of the lines "Touch sense", "Voice
volume" and "Signal volume", you can adjust the
corresponding behavior of the transmitter to your
requirements. And, in the event that you (would like to)
commission your transmitter in France, the setting in the
"Region" line is important: The legal regulations of this
country require the selection of "France" instead of the
default setting "Euro".
If these settings are activated, it continues with the
menu ...
"Model select" (page 63)
Select a free storage location with the arrow keys ...
03
04
05
¿¿¿
free
¿¿¿
02
01
06
R12
¿¿¿
free
¿¿¿
¿¿¿
free
¿¿¿
¿¿¿
free
¿¿¿
¿¿¿
free
¿¿¿
…and open this by briefl y pressing the central SET
key of the right touch pad. In the subsequently opening
display, with the key f of the left or right touch pad,
select…
Select model typ
… the "Heli" model type. The display immediately
switches to the base screen if you confi rm this selection
by briefl y pressing the central
SET key of the right touch
pad.
Notice:
If the "Select model type" option has been opened, •
the process cannot be canceled. Even if you switch
off the transmitter, this selection must be made! In
any case, you can undo this by subsequently deleting
the respective model memory.
If the "Throttle too high" warning appears, this can •
be deleted by turning the proportional rotary control
CTRL 6 counterclockwise until its limit.
If battery voltage is too low, the model switchover •
cannot be made due to reasons of safety. An
appropriate message will appear in the screen:
not possible now
voltage too low
Once this fi rst hurdle is cleared, the connection of the
receiver built into the model at this model memory must
be made in the menu …
"Base setup model" (page 74 … 80)
. For this purpose, switch to the line "RF bind":
1
n/a
n/a
BD1
Starlet
BD2
E12
Mod.name
Stick mode
RF BIND
BASIC SETTINGS, MODEL
RF transmit
OFF
Notice:
After confi rmation of the model selection in the base
screen, if you confi rm the message appearing in the
screen for a few seconds …
BIND N/A
OK
… by pressing the SET key of the right touch pad, you
automatically come to this line.
In the line"RF Bind." you delete the connection process
between model memory and receiver, as described in
detail on page 74. Otherwise, you cannot address the
receiver.
Afterwards, using the arrow keys of the c
 left or right
four-way pad, move up to the fi rst line and begin with
the actual model programming in the "Mod. Name" line:
Now enter an appropriate name for the model memory,