User's Manual

126
Program description: Telemetry menu
RX + VARIO
RXSQ
0
MAX
+500m
MIN
+500m
ALT
+500
H
L
m/1s
0
m/3s
0
m/10s
0
If a Vario module, Order No. 33601, is connected to the
receiver, then this screen provides a graphic display
of the data supplied by it. For more information on this
module please see the Appendix or refer to the product
on the Internet at www.graupner.de.
The meanings are as follows:
Value Explanation
ALT Current altitude
RXSQ Signal strength of the signal picked up
by the receiver in %
MAX The pre-set altitude limit relative to
the launch point; above this altitude
the transmitter emits audible warning
signals
MIN The pre-set altitude limit below the
launch point; below this altitude the
transmitter emits audible warning
signals
m/1s m/1 sec climb / descent
m/3s m/3 sec climb / descent
m/10s m/10 sec climb / descent
RX + GPS
N
RXSQ 0
DIS 0m
ALT +500m
0m/1s
0m/3s
0m/10s
N 0°00.0000
E 0°00.0000
W
E
S
Kmh
0
If a GPS module with integral vario, Order No. 33600,
is connected to the receiver, then this screen provides
a graphic display of the data supplied by it. For more
information on this module please see the Appendix, or
refer to the product on the Internet at www.graupner.de.
The centre of the screen shows the current positional
data and the model’s speed; the display also shows the
model’s current altitude in relation to the launch point, its
climb / descent rate at m/1 sec, m/3 sec and m/10 sec,
the current reception quality and the model’s range from
the launch point.
The meanings are as follows:
Value Explanation
W / N / E / S West / North / East / South
Kmh Speed
RXSQ Signal strength of downlink channel
DIS Distance
ALT Current altitude relative to launch point
m/1s m/1 sec climb / descent
m/3s m/3 sec climb / descent
m/10s m/10 sec climb / descent
83
Operating Notes
Adjusting stick length
Both sticks are infi nitely variable in length over a broad
range, enabling you to set them to suit your personal
preference.
Hold the bottom half of the knurled grip fi rmly, and
unscrew the top section:
Now screw the stick top in or out (shorter or longer)
to the length you prefer before tightening the top and
bottom sections against each other to fi x the stick top.
Opening the transmitter case
Please read the following notes carefully before you
open the transmitter. If you have no experience in such
matters, we recommend that you ask your nearest
Graupner Service Centre to carry out the work for you.
The transmitter should only be opened in the following
cases:
When a self-neutralising stick needs to be converted
to non-neutralising action, or a non-neutralising stick
to a self-neutralising action.
If you wish to adjust the stick centring spring tension.
Before opening the transmitter check that it is switched
off (move Power switch to “OFF”).
Open the battery compartment and remove the transmit-
ter battery as described on the previous double page.
After this, use a PH1-size cross-point screwdriver to
undo the six screws recessed into the back panel of the
transmitter, as shown in the illustration:
Arrangement of the case back screws
Hold the two case sections together with your hand, and
turn the unit over to allow these six screws to fall out
onto the table. Now carefully raise the case back and
fold it open to the right, as if you were opening a book.
C A U T I O N
Two multi-core cables connect the lower shell to the
transmitter electronics located in the top section.
Please take great care not to damage this cable!
Important:
Do not modify the transmitter circuit in any way,
as this invalidates your guarantee and offi cial ap-
proval for the system.
Do not touch any part of the circuit boards with
any metal object. Avoid touching the contacts
with your fi ngers.
Never switch the transmitter on while the case is
open.
Please note the following points when closing the
transmitter:
Make sure that no cables are jammed between the
transmitter case sections when you close the back.
Check that the two case sections fit together flush all
round before fitting the retaining screws. Never force
the two case components together.
Fit the case screws in the existing threads, and tigh-
ten them gently. Over-tightening them will strip the th-
reads in the plastic.
Remember to re-connect the battery.
33110_mx10_HoTT_1_DE.indd Druckbogen 83 von 104 - Seiten (126, 83)
33110_mx10_HoTT_1_DE.indd Druckbogen 83 von 104 - Seiten (126, 83)
21.10.2011 13:25:19
21.10.2011 13:25:19