User's Manual
84
Operating Notes
Operating Notes
Converting the dual-axis stick units
Self-centring action
Either or both sticks can be converted from self-neutrali-
sing to non self-neutralising action: start by opening the
transmitter as described on the previous page.
If you wish to change the standard stick unit arrange-
ment, start by locating the screw on the left-hand stick
unit shown circled in white in the photo below.
Note:
The right-hand stick unit is of mirror-image construction,
i. e. the screw you require is located on the right, below
centre.
Turn this screw clockwise until the stick on that side
moves freely from one end-stop to the other; alterna-
tively unscrew it until the stick is fully self-centring again.
Charge socket
Brake springs
Adjuster screws
Brake springs
Adjuster screws
folding areal
Self-centring screw
Self-centring screw
Adjuster screws for stick centring force
Do not touch trans-
Do not touch trans-
mitter circuit board
mitter circuit board
Do not touch trans-
Do not touch trans-
mitter circuit board
mitter circuit board
Left-hand stick unit
Left-hand stick unit
Right-hand stick unit
Right-hand stick unit
125
Program description: Telemetry menu
The meanings are as follows:
Value Explanation
BAT1 / BAT2 Battery 1 / Battery 2
FUEL Fuel level / Fueltank indicator
E / F Empty / full
T1 / T2 Temperature of sensor 1 / sensor 2
CELL V Cell voltage of cell 1 … max. 6
1500 RPM
ALT Current altitude
0m1 m/1 sec climb / descent
0m3 m/3 sec climb / descent
POWER V. Actual voltage of the drive battery
A Actual current of drive battery
450 Actual used capacity
RX + ELECTRIC AIRMODUL
0.0V 0m/3s
BAT1 0m/1s
BAT2
0.0V T2 +20°C
T1 +20°C
CELL V
1L0.00
2L0.00
3L0.00
4L0.00
5L0.00
6L0.00
0.0V 0A
ALT +500m
7L0.00
0.0V 0m/3s
BAT1 0m/1s
BAT2
0.0V T2 +20°C
T1 +20°C
CELL V
1H0.00
2H0.00
3H0.00
4H0.00
5H0.00
6H0.00
0.0V 0A
ALT +500m
7H0.00
RX + GENERAL MODUL
0.0V
BAT1
BAT2
0.0V T2 +20°C
T1 +20°C
E FUEL F
CELL V
1:0.00
2:0.00
3:0.00
4:0.00
5:0.00
6:0.00
1500
0.0V
BAT1
BAT2
0.0V T2 +20°C
T1 +20°C
E FUEL F
ALT
+500m
0m1
0m3
POWER
14.8V
10.3A
450
If a General Engine module, Order No. 33610, or a
General Air module, Order No. 33611, is connected to
the receiver, then this screen provides a graphic display
of the data supplied by it. For more information on these
modules please see the Appendix, or refer to the pro-
duct on the Internet at www.graupner.de.
Depending on the types of sensor fi tted to the modules,
the display constantly shows the following data:
The actual voltage of up to two rechargeable batteries
(BAT1 and BAT2); the measured values from up to two
temperature sensors (T1 and T2) and a fueltank level
indicator.
At the right-hand edge the screen shows either an al-
ternating list of the actual cell voltages of a LiPo battery
with up to six cells, or the current altitude relative to the
location, climb / descent in m/1sec and m/3sec, current
in Ampere plus the actual voltage of the battery connec-
ted to the sensor.
If an Electric-Air module, Order No. 33620, is connec-
ted to the receiver, then this screen provides a graphic
display of the data supplied by it. For more information
on this module please see the Appendix, or refer to the
product on the Internet at www.graupner.de.
Depending on the types of sensor fi tted to the module,
the display constantly shows the following data:
The actual voltage of up to two rechargeable batteries
(BAT1 and BAT2); the measured values from up to two
temperature sensors (T1 and T2); the current altitude
relative to the location, and the climb / descent of the
model in m/1sec and m/3sec; the centre of the screen
also displays the current actually being drawn from a
power source.
At the right-hand edge the screen shows an alternating
display of the actual cell voltages of the battery packs
(max. seven cells each) connected to balancer sockets
1 (L) or 2 (H).
The meanings are as follows:
Value Explanation
V Actual voltage
A Actual current
BAT1 / BAT2 Battery 1 / Battery 2
ALT Current altitude
m/1s m/1 sec climb / descent
m/3s m/3 sec climb / descent
T1 / T2 Temperature from sensor 1 / 2
CELL.V Cell voltage of cell 1 … max. 14
L Balancer socket 1
H Balancer socket 2
33110_mx10_HoTT_1_DE.indd Druckbogen 84 von 104 - Seiten (84, 125)
33110_mx10_HoTT_1_DE.indd Druckbogen 84 von 104 - Seiten (84, 125)
21.10.2011 13:25:22
21.10.2011 13:25:22