User's Manual

124
Program description: Telemetry menu
MODEL SELECT
Select the desired menu line „MODEL SELECT“ using
the
INC button.
No
w press ENTER …
CAR
AIRPLANE,HELI.,GLID.
and again ENTER ...
RECEIVE
RECEIVE+GENERAL/GAS
RECEIVE+ELECTRONIC
RECEIVE+VARIO
RECEIVE+GPS
… press the INC-button to choose the sensor with the
arrow and fi nally press ENTER to select:
RX–S QUA: 100%
RX–S ST : 100%
TX–dBm: 33dBm
RX–dBm: 33dBm
RX–VOLT:4.8 TMP
V–PACK: 10ms
CH OUTPUT TYPE:ONCE
M–RX V :4.6 +22°C
DATA VIEW
RECEIVER
RX–S QUA: 100%
RX–S ST : 100%
TX–dBm: 33dBm
RX–dBm: 33dBm
RX–VOLT:4.8 TMP
V–PACK: 10ms
CH OUTPUT TYPE:ONCE
M–RX V :4.6 +22°C
This screen displays the data which can also be viewed
in the “RX DATAVIEW” screen of the telemetry menu
“SETTING & DATA VIEW”, but in graphic form.
The meanings are as follows:
Value Explanation
RX-S QUA Signal quality in %
RX-S ST Signal strength in %
RX-dBm Receive performance in dBm
TX-dBm Transmit power in dBm
V PACK shows the longest period in ms in
which data packets were lost in
transmission from transmitter to
receiver
RX-VOLT Current receiver operating voltage in
Volt
M-RX V Lowest receiver operating voltage in
Volt since the last time it was switched
on
TMP The thermometer indicates the
receiver’s current operating
temperature
Just like described in the menu „MODEL SELECT“ ...
RECEIVE
RECEIVE+GENERAL/GAS
RECEIVE+ELECTRONIC
RECEIVE+VARIO
RECEIVE+GPS
...the output can be selected to graphically processed
data from a sensor connected to the receiver if
necessary. These data are then presented according to
the following graphic displays.
Scroll back and forth between the different graphic
displays with the INC or DEC key and choose by
pressing ENTER, press ESC to return back to the basic
display.
Note:
The order of displays described below follows the
sequence when pressing the INC button.
More details about the following modules can be found
in the appendix and on the internet at www.graupner.de
for the relevant product.
85
Operating Notes
Stick centring force
The centring force of the sticks is also variable to suit
your preference. The adjustment system is located
adjacent to the centring springs; see the white circles in
the following photo.
You can set the preferred centring spring force by
rotating the corresponding adjuster screw using a cross-
point screwdriver:
Turn to the right = harder spring tension;•
Turn to the left = softer spring tension.•
horizontal
horizontal
vertical
vertical
Note:
The right-hand stick unit is of mirror-image construction,
i. e. the screw you require is located on the right, below
centre.
Brake spring and ratchet
You can alter the braking force of the stick by adjusting
the outer of the two screws circled in white in the next
picture; adjusting the inner screw alters the strength of
the ratchet:
Note:
The right-hand stick unit is of mirror-image construction,
i. e. the screw you require is located on the right, below
centre.
33110_mx10_HoTT_1_DE.indd Druckbogen 85 von 104 - Seiten (124, 85)
33110_mx10_HoTT_1_DE.indd Druckbogen 85 von 104 - Seiten (124, 85)
21.10.2011 13:25:25
21.10.2011 13:25:25