User's Manual
114
Program description: Telemetry menu
Telemetry
The menus grouped together under the overall heading
“Telemetry” are called up with the optional available
Smart-Box
Install the SMART-BOX at the mounting bracket of the
transmitter fi gure. Connect the box then the 3-pin lead to
the transmitter. Put one end of the cable into the DATA
jack on the transmitter and the other into the jack on the
right side of the SMART-BOX. The connector system is
polarised, look for the small camfer on the edges. Never
use force - the plug should engage easily and fully. The
sockets are labeled accordingly: black wire (-), red wire
(+) and orange wire (S).
Basic menu operation
In general terms the “Telemetry” menu is operated with
the four buttons on the top of the Smart-Box. You can
switch between the individual pages of the Telemetry
menu using the
ESC and ENTER buttons: you will fi nd
corresponding direction indicators at top r
ight of every
screen page in the form of angle brackets (< >); see
illustrations. If only one angle bracket is visible, then you
are currently at the fi rst or last page. In this case it is
only possible to switch pages in the direction indicated
by the angle bracket.
Menu lines in which parameters can be altered are
marked with an angle bracket prefi x (>). Pressing the
buttons INC and DEC causes the “>” pointer to jump
f
orward or back by one line. Lines to which you cannot
jump contain no user-variable values.
If you wish to change a parameter, press the INC+DEC
b
utton simultanously to highlight the parameter (black
background)). Change the value within the possible
range using the
INC or DEC buttons, and then press the
INC+DEC button again briefl y to accept the value. Press
the
ESC button to return back to starting position.
SETTING & DATA VIEW
MENU SETTING AND DATAVIEW
On the fi rst screen page of the sub-menu “Setting &
Data View”, headed …
TX
... only partially adjustments can be made. This page
provides information to the general transmitter settings:
TX
MAXIMUM VOLT: 05.5V
MINIMUM VOLT: 05.4V
ALARM VOLT: 04.7V
COUNTRY : GENERAL
ACTION VOLT: 05.4V
RANGE TEST : OFF 90s
Display Description Setup
ACTION
VOLT
Current operating
voltage (V)
-
MAXIMUM
VOLT
Maximum
operating voltage
(since the last
power on - V)
-
MINIMUM
VOLT
Minimum
operating voltage
(since the last
power on - V)
-
ALARM
VOLT
voltage setup for
transmitter low
voltage warning
beep
4 – 15 V in steps of
0.1 V
Factory setting
4.5 V
COUNTRY Country setting GENERAL /
FRANCE
RANGE
TEST
indicates if the
range test is
engaged, the
remaining
time also appears
OFF / ON
Transmitter low-voltage warning (ALARM VOLT)
you can adjust the low voltage threshold at which the
alarm (continuous beeping) is triggered; the available
range is 4 - 15 V - factory default setting 4.5 Volt.
When the alarm is triggered, “VOLT-E” fl ashes at top
right in the SMART-BOX transmitter display, and the
parameters ACTION VOLT and ALARM VOLT are
displayed in inverse form.
SETTING & DATA VIEW
95
Using the receiver for the fi rst time
The fi rmware fi les are present in a product-speci-
fi c encoded form, i.e. if you inadvertently select a fi le
which does not match the product (e.g. transmitter
update fi le instead of receiver update fi le) the pop-up
window “Product code error” appears, and the update
process cannot be started.
If you have not already done so, switch the recei-
vers power supply OFF at this point and start the re-
ceivers update procedure by clicking on the “Down-
load Start” button. Wait until the progress bar starts
running. This can take up to several seconds. Now
switch the receiver ON with the SET-Button pressed.
After a few seconds, the status display „Found target
device ...“ appears. Now release the SET-Button. The
actual update process now commences, and a pro-
gress bar starts running:
On the other hand, if the device is not recognised,
the pop-up window “Target device ID not found” ap-
pears.
If the process is interrupted before the progress bar
reaches the 100% mark, switch off your receiver po-
wer supply and carry out another attempt at the up-
date process, i.e. repeat all the steps described abo-
ve.
The Status Display and the progress bar show the
progress of the fi rmware update process. The update
is completed when the message “Download Process
Complete!!” appears.
During the update process the green LED on the re-
ceiver light up. When the update is completed, the
green LED goes out.
Switch the receiver off, and disconnect the interface
lead. If you have multiple receivers, you must repeat
the procedure with each one.
4. Initialising the receiver
Once you have completed the update process, for
safety reasons you MUST initialise the receiver befo-
re using it again:
Hold the SET button on the receiver pressed in while
you switch on its power supply; then release the SET
button again after approx. 3 sec - the green LED ex-
pires. If you now switch the transmitter on again, after
about two or three seconds the green LED on the re-
ceiver will light up constantly. However, all the other
previously programmed settings in the receiver - with
the exception of the binding information - are now re-
set to the factory default values, and you will need to
re-enter them if required.
33110_mx10_HoTT_1_DE.indd Druckbogen 95 von 104 - Seiten (114, 95)
33110_mx10_HoTT_1_DE.indd Druckbogen 95 von 104 - Seiten (114, 95)
21.10.2011 13:25:41
21.10.2011 13:25:41