User's Manual

25
Description of transmitter - screen and keypad
Operating the “Data Terminal”
Input buttons ESC, SET, CLEAR,
symbols
On-screen telemetry symbols
The active model memory is not yet “bound”
Not fl ashing: RF switched off at transmitter
Flashing aerial symbol:
The last receiver bound to the active model is
inactive, or out of range
>M x No telemetry signal detected
>M
Signal strength display
>P
Display of Pupil signal strength on the Teacher
transmitter’s screen.
Buttons to the left of the screen
ESC• button
Pressing the ESC button returns you step by step
within the function select system, taking y
ou right
back to the basic display. If you make a change in the
meantime, the change is retained.
If pressed for about one seconds in the base display,
ESC opens and closes the Telemetry menu.
Arro
w buttons • ef cd
Pressing one of these buttons allows you to leaf 1.
through lists, such as the Model Select or Multi-
Function list, always moving in the direction of the
arrow; the arrow buttons are also used to move
through menu lines within menus.
Simultaneously pressing the 2. ef buttons switch-
es from the base transmitter display, and from al-
most any menu position, into the “Servo display”
menu.
Buttons to the right of the screen
SET• button
Star
ting from the base screen display - as it ap-1.
pears when you switch the transmitter on - a brief
press of the SET button takes you to the multi-
function men
us. You can also call up a selected
menu using the SET button.
Within the set-up menus you can activate (con-2.
fi rm) and disable the corresponding set-up fi elds
by pressing the SET button.
Arro
w buttons • ef cd
1. “Leafs through” the multi-function menu and the
menu lines within the set-up menus, in the same
manner as the left-hand four-way arrow buttons.
2. Selects and adjusts parameters in set-up fi elds af-
ter you have activated them by pressing the SET
b
utton; the buttons fc and ed are assigned
the same function in each case, i. e. it makes ab-
solutely no difference which of the two buttons
you use.
3. A brief simultaneous press of the cd or ef
buttons resets an altered parameter value in the
active input fi eld to the default value (CLEAR).
Notes:
If you switch the transmitter off and then immediately
on again, you may fi nd that the four-way buttons have
no effect. This is not a fault! Switch the transmitter off
again, and wait a few seconds before switching it on
once more.
Short-Cuts
You can call up particular menus or options directly us-
ing the following button combinations:
CLEAR•
A brief simultaneous press of the cd or ef but-
tons of the right-hand four-way button resets an al-
tered parameter value in the active input fi eld to the
default value.
“• Servo display”
A brief simultaneous press of the ef buttons of the
left-hand four-way button switches from the transmit-
ter’s base display, and from almost any menu posi-
tion, to the “Servo display”, menu; see page 113.
“• Telemetry”
Press the central ESC button of the left-hand four-
w
ay button for about one second at the transmitter’s
base display; see section starting on page 117.
“• HIDDEN MODE”
(language selection and contrast)
Simultaneously press the arrow buttons cd of the
left-hand four-way button AND the central SET but-
ton of the r
ight-hand four-way button; see next dou-
ble-page.
Input lock•
Can be activated and disabled at the transmitter’s ba-
sic display by simultaneously holding the ESC and
SET buttons pressed in for about two seconds.
33112_mx12_HoTT_2_GB.indd Abs7:2533112_mx12_HoTT_2_GB.indd Abs7:25 06.06.2011 19:39:3306.06.2011 19:39:33