User's Manual
132
Program description: Trainer system
Trainer Mode
Connecting two transmitters for trainer mode operations using a Trainer lead
Use the arrow buttons of the left or right-hand touch-key
to leaf through to the “Trainer” menu point of the multi-
function menu:
servo set.
D/R expo
wing mixer
contr set.
phase trim
free mixer
servo disp basic sett
fail-safe
telemetry
info dispteach/pupi
servo set.
D/R expo
free mixer
contr set.
heli mixer
swashp.mix
servo disp basic sett
fail-safe telemetry
teach/pupi info disp
Touch the central SET button of the right-hand touch-key
to open the menu:
TRAINER/Pupil
–P
T
23
4
5
6
78
BIND:SW: –––
1
N/A
The illustration above shows the initial state of this
menu: transmitter controls have not been released (
) to
the pupil, and a switch has not been assigned (SW: ---
at bottom right and -P on the left of the display).
Teacher transmitter settings
Up to eight transmitter control functions of the Teacher
transmitter “T” can be transferred individually or in any
combination to the pupil transmitter “P”.
The lower line of the display marked “T” therefore
indicates those transmitter controls which are perma-
nently connected to the inputs 1 … 4 (dual-axis stick
functions, fi xed-wing model and model helicopter), plus
the transmitter controls CTRL 6 to 8, which can be
assigned to inputs 5 … 8 in the “Transmitter control
settings” menu.
Notes:
This means that the three-position switches SW 4/5 •
and 6/7, designated CTRL 9 and 10, explicitly CAN-
NOT be transferred.
Transmitter controls can only be assigned in the •
“Transmitter control settings” menu when the Train-
er connection is switched off.
Use the arrow buttons ef of the left or right-hand
touch-key to select the transmitter controls 1 to 8 (z) to
be transferred to the pupil, and briefl y press the central
SET button of the right-hand touch-key in each case, so
that the
y switch from “T (Teacher)” (
) to “P (Pupil)” ( ):
–P
T
123
4
6
78
5
BIND:SW: –––
N/A
TRAINER/Pupil
You still have to assign a Trainer transfer switch on the
right of the screen so that you can actually transfer con-
trol to the Pupil. This is accomplished by using the arrow
buttons of the left or right-hand touch-key to place the
marker next to “SW” at bottom right, and assign a switch
as described on page 39.
We recommend that you use one of the two momentary
switches SW 1 or SW 9 as the transfer switch, to ensure
that the Teacher transmitter can regain control instantly
at any time.
¿
T
123
4
5
6
78
P
BIND:SW:
N/A
9
TRAINER/Teach
Note:
The switch assignment procedure described above
determines which transmitter provides the Teacher
function, and which provides the Pupil function. For this
reason a switch must NEVER be assigned to the Pupil
transmitter in this menu. To underline this, the menu
headline switches from “TRAINER / pupil” to “TRAI-
NER / teacher” as soon as a switch is assigned.
The model to be controlled by the pupil must be pro-
grammed completely in a model memory of the mx-
16 HoTT Teacher transmitter, i. e. with all its functions
including trims and any mixer functions. The HoTT re-
ceiver in the model must also be “bound” to the Teacher
transmitter, since it is this transmitter which actually
controls the model in Pupil mode, even in Trainer opera-
tions.
The mx-16 HoTT Teacher transmitter MUST ALWAYS
BE SWITCHED ON FIRST. ONLY THEN MAY THE
CONNECTING LEAD BE PLUGGED INTO IT. If you