No. S1002.mz-12 HoTT. USA mz-12 OPERATING INSTRUCTION Prior to use, please read this manual thoroughly. Keep this manual in a convenient place for quick and easy reference.
Contents • Before Use • Support and Service - Customer support - Internet sales site - A/S regulation - Warranty regulation • Openhobby A/S Center 1. Box Contents 2. Safety Notes 3. Features 4. Transmitter Control Identification 5. Specification 6. Display Explanation 7. Adjustable Stick Length 8. Adjustable Stick Testion 9. Mode exchange of throttle stick for Mode 1 and Mode 2 10. What is HoTT 11. Battery Installation 12. Binding • The Transmitter Programming Setup 1.
2. FLYING SAFETY BEFORE USE Thank you for purchasing mz-12 HoTT 2.4GHz Radio System. This system is extremely versatile and may be used by beginners and pros alike. In order for you to make the best use of your system and to fly safely, please read this manual carefully. If you have any difficulties while using your system, please consult the manual, our online Frequently Asked Questions (on the web pages referenced below), your hobby dealer, or the Graupner Service Center.
. TRANSMITTER CONTROL IDENTIFICATION ANTENNA TX HANDEL S4 SWITCH R F T R AIN ER SW IT C H S2 SWITCH DIAL VOLUME S1 SWITCH S3 SWITCH BATTERY COVER NECKSTRAP LUG ELEV/RUDO STICK ELEV/TRIM THRO/AILE STICK THRO TRIM POWER SWITCH RUDD TRIM AILE TRIM DIRECTION BUTTON ENT, ESC, TEL VIEW BUTTON EAR PHONE CHARGE SOCKET DATA PIN 4
. SPECIFICATION Frequency band Modulation Output power Current drain Operating voltage Transmitter mz-12 Receiver 8 Ch 2.4~2.4835GHz FHSS 100mW Approx 125mA 3.4V~6V 2.4~2.4835GHz FHSS Approx 70mA 3.6V~8.4V 6. DISPLAY EXPLANATION 2 3 1 16 4 15 5 14 6 13 7 12 8 11 1. Receiver signal indicator 2. Button Lock status 3. Battery voltage of receiver 4. Timer 5. Flight timer 6. Trainer indicator 7. Q. LINK 8. Aileron trim 10 9 9. Throttle trim 10. Transmitter type 11. Elevator trim 12.
9.
9 Assemble the centering cam into the throttle gimbal of mode 1 transmitter and set the spring in the center control part and the centering cam with tweezers 10 Screw the disassembled tension control bolt from the elevator gimbal of mode 1 transmitter into the throttle gimbal and adjust the bolt for the desired control Ratchet Type Options and Strength Adjustment for Throttle Stick. There are two options for the ratchet type of throttle stick.
The Spring Strength Adjustment of Elevator, Aileron and Rudder Stick. According to your preference, you can adjust the spring tension by tightening the related screws for elevator, aileron and rudder stick. There are related screws beside return-spring as below picture. You can tighten the related screws for tension its adjustment (elevator, aileron and rudder). There are the screws at the black-colored circles. You can tighten the screw for stronger and loosen for smoothly.
2. The model men is highlighted then press the direction button to highlight RF sett. 4. After completing the bind, press the ESC button to return to the home screen. ENT ENT TEL TEL VIW VIW ESC ESC press 3. Press the ENT button, the cursor is automatically on the stick mode line then press the direction button to select the hyphen in the rx bind line. Turn on the receiver then press the ENT button on the receiver for over 3 seconds so that the receiver enter the binding mode.
press press ENT TEL ENT VIW TEL ESC VIW ESC - Select model In the home screen, press the ENT button then the model mem is highlighted. Press the ENT button to access the function. press ENT TEL press VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC Press the direction button to select the model then press the ENT button to access the Sel model type screen.
ENT ENT TEL VIW ENT TEL VIW ESC ESC press press press press ENT TEL ENT VIW VIW TEL ESC press VIW ENT TEL VIW ESC ENT VIW TEL ESC VIW ESC ENT TEL VIW ENT ESC TEL VIW ESC press press ENT TEL VIW ESC press ENT TEL VIW ESC - Clear model When the model mem is highlighted, press the ENT button then the cursor is on the select model line. Press the direction button to select the clear model line then press the ENT button to access to the function.
- Copy mod->mod The model mem is highlighted in the menu screen then press the ENT button. The cursor is on the select model line. Press the direction button to select the copy mod ->mod line then press the ENT button to access to the function. When the copy from model screen appears, press the direction button to highlight the model you want to copy then press the ENT button to accept.
press • Q uick link set : The quick link sett function allows to adjust the D/R expo value and to assign the corresponding switch to cope with various flight conditions such as 3D flight or the flight with the strong wind. Since the adjusted value is activated by moving the switch, you can cope with various flight conditions with switch. It makes you operating the flight much easier. You can select take off, thermal, dist, speed, acro, landing, air-tor, test at quick2 and quick3.
ENT TEL VIW ESC - Motor at C1 idel re The idle position of the throttle stick (C1) is back, toward the user, if the throttle stick is not there, the throttle warning message “Throttle too high” appears and the cut off option is activated. - Cut off When the option of “idle re” or “idle fr” is selected, the cut off option is activated. It turns off the internal combustion engine or the electric motor.
Press the direction button to select the value,+150%,. Place the throttle stick at the desired position and press the ENT button then the adjusted value is applied (The adjusted value is activated when the throttle stick is in that position). NOTE : the value,+150%, is the throttle stick position where the cut off function is activated.
ENT TEL VIW ESC press ENT TEL Motor at C1 Tail type VIW ESC Aile/flap no, no/inv normal,V-tail,delt/FlW 1 aile 1 aile 1 flap 2 aile 2 aile 1 flap 2 aile 2 flap 2 elev sv 1 aile 1 aile 1 flap 2 aile 2 aile 1 flap normal,V-tail 1 aile 1 aile 1 flap 2 aile 2 aile 1 flap Idle re, idel fr Delt/FlW 2 aile 2 aile 1 flap 2 aile 2 flap 2 elev sv 1aile 1 aile 1 flap 2 aile NOTE : The correct value should be matched each other since the some value is not match to the others, refer to the table.
ENT ENT TEL TEL VIW press press TEL VIW VIW ESC ESC press press ENT ENT TEL press ENT ENT TEL VIW ESC ESC TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW VIW ESC ESC press - Quick link sett The quick link sett function allows to adjust the D/R expo value and to assign the corresponding switch to cope with various flight conditions such as 3D flight or the flight with the strong wind.
press ENT TEL ENT VIW TEL ESC VIW ESC press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW VIW ESC ESC press - Quick link trim Use the quick link trim function to program the appropriate trims of the quick 2 and quick 3 in the quick link. The user can program the trim in advance to cope with the unexpected situation such as the flight with the strong wind and match the flight situation of the takeoff , thermal and speed of the glider.
ENT TEL VIW ESC After completing the normal quick link adjustment, press the direction button to select the thermal quick link line. The thermal quick link and speed quick link can be programmed in the same method. If you already set the quick link switch and the switch is ON, the cursor is automatically moved to the corresponding quick link value.
• Aurtorotat You may set the switch to be used as auto rotation. If the switch is on, throttle channel is hold at 90% position and pitch, elevator and aileron that is connected to throttle channel are normal operated. It is the same function with throttle hold. • Quick link sett The quick link sett function allows to adjust the quick2 value and assign the corresponding switch to cope with various flight conditions such as 3D flight or the flight with the strong wind.
ENT TEL ENT VIW TEL ESC - Cut off Press the direction button to select the cut off line then press the ENT and the direction button to highlight and adjust the value less than -100%. Press the ESC button to remove the highlight. NOTE : The value of -100% is the cut off position the user can program, if the cut off value is programmed less than -100%, the breathing hole of Engine carburetor is block or the speed controller lets the motor off so the power is not delivered to the Helicopter.
ENT TEL VIW ESC - Pitch min Use the pitch min function to reverse the servo direction in all of pitch, elevator, aileron and throttle channels, the default value is rear. Available settings are rear and front. Press the direction button to select the pith min line then press the ENT button to highlight the pitch min value. Press the direction to select the desired value (rear or front) then press the ESC button to remove the highlight.
press ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC VIW ESC - Quick link sett The quick link sett function allows to adjust the quick2 value and assign the corresponding switch to cope with various flight conditions such as 3D flight or the flight with the strong wind.
ENT ENT TEL TEL VIW VIW ESC ESC 3. Servo sett (Aircraft and Helicopter) ENT TEL VIW ESC press ENT TEL VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC The servo sett adjusts the servo reverse, center, travel for all six channels. - Rev : used to reverse the servo direction for all channels. - Cent : used to set the neutral position of the servo. - Trv : used to increase or decrease the moving angle of the servo travel.
press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press VIW ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC press VIW ESC press 25
press ENT TEL ENT VIW TEL ESC press press ENT TEL VIW ESC VIW ENT ESC TEL VIW ESC press ENT TEL ENT VIW ESC TEL VIW ESC 4. Cont sett (Aircraft and Helicopter) It contains 3 categories: model type, quick link set and quick link trim. You can program the 5 and 6 channels in mz-12 to the special function that you want. Typically, the 5 channel is used for the on/off switch of the retractor gear and the 6 channel is used for the on/off switch of the flap function.
ENT TEL VIW ESC ENT TEL VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC press ENT TEL VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC - Cont sett (Helicopter) The basic setting of the Helicopter cont sett is NO.5 gyro, NO6. Throttle, Lim. DV (Digital volume). Generally, this function is seldom used, but Lim.
5. D/R expo (Aircraft and Helicopter) The basic setting of the Helicopter cont sett is NO.5 gyro, NO6. Throttle, Lim. DV (Digital volume). Generally, this function is seldom used, but Lim. DV (Digital volume) can control the operation range of digital volume -100 ~ +100. If DV is programmed, throttle channel is operated only programmed range. - D/R Affects the overall travel which in turn affects control response sensitivity equally throughout the range of that channel.
press ENT TEL VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL • Timer The mz-12 has four stick modes with the two dual axis sticks. The user can select one among the four default stick modes the default mode is the mode 1. • Receiv out For the maximum flexibility of the receiver socket assignment, the mz-12 provides to swap over the servo outputs 1 to max.6.
- Stick mode Enter the stick mode from the RF sett on the menu. Press the ENT button to highlight the value then press the direction button to select the mode number of 4 modes. ENT TEL press VIW ESC ENT TEL VIW press ESC ENT TEL VIW ESC ENT TEL press VIW ESC ENT press TEL VIW ESC ENT TEL VIW press press ESC ENT press TEL VIW ESC ENT TEL VIW ESC ENT TEL - Timer Press the direction button to select the timer line and press the direction button again to select the minute or second.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC - Receiv out Press the direction button to select the receiv out line then press the ENT button to access the function. The cursor is on the arrow mark then press the ENT button to access the function. -The default channel assignment- The default channel assignment appears on the screen.
press ENT TEL VIW ESC ENT TEL VIW ESC - RF transmit RF transmit function allows to turn ON/OFF the RF power output. Press the direction button to select the RF transmit then press the ENT button to select ON or OFF. press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC press ENT TEL VIW ESC 32 7. wing mix (AIRCRAFT) • Diff aile The diff aile mixing allows to overcome the adverse yaw when the Aircraft is deflected.
- Diff aile Press the ENT button to access the diff aile mixing then press the ENT button again to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears. Move the switch then the corresponding value appears (The diff aile mixing is on/off when the switch is moved).
press ENT ENT TEL TEL VIW press press ENT ENT TEL TEL VIW VIW ESC ESC ENT TEL VIW ESC ESC ENT VIW TEL ESC VIW ESC press - Ail->rudd Press the direction button to select the ail -> rudd line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT TEL ESC press press press ENT TEL ENT TEL VIW ESC VIW VIW ESC VIW ESC press ENT TEL ENT TEL VIW ESC VIW ESC press press ENT ENT TEL VIW TEL VIW ESC ESC ENT TEL - Brak->elev Press the direction button to select the brak -> elev line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight.
- Brak->flap Press the direction button to select the brak -> flap line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears. Move the switch then the corresponding value appears (The brak -> flap mixing is on/off when the switch is moved).
press ENT ENT TEL TEL VIW ESC ENT ENT TEL TEL VIW press ENT TEL VIW ESC VIW ESC ESC - Elev->flap Press the direction button to select the elec -> flap line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears.
ENT TEL ENT VIW TEL ESC VIW ESC press press press ENT ENT TEL TEL VIW press ENT TEL VIW ESC ENT TEL VIW ESC - Flap->elev Press the direction button to select the flap -> elev line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears.
ENT ENT TEL TEL VIW press press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT TEL ENT VIW TEL ESC press VIW ESC ESC VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC - Diff-red Press the direction button to access the diff-red mixing then press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. press ENT TEL VIW ESC 8.
- Ptch Press ENT button to access the ptch mixing then press the ENT button again to access the function. -100% of the point 1 value is highlighted. Move the throttle stick to the high position step by step then the point 2,3,4,5 is selected in turn. After selecting the point number, press the direction button to adjust the desired value. Press the ESC button to return to the previous screen.
ENT TEL ENT VIW TEL ESC VIW ESC press - Pitc->thro Press the direction button to select pitc->thro line and press the ENT button to access the pitc->thro function. 0% of the point 1 value is highlighted. Move the throttle stick to the high position step by step then the point 2,3,4,5 is selected in turn. After selecting the point number, press the direction button to adjust the desired value. Press the ESC button to return to the previous screen.
ENT TEL VIW ENT ESC - Pitc->rudd ruddPress the direction button to select pitc->tail line and press the ENT button to access the pitc-> tail function. 0% of the point 1 value is highlighted. Move the throttle stick to the high position step by step then the point 2,3,4,5 is selected in turn. After selecting the point number, press the direction button to adjust the desired value. Press the ESC button to return to the previous screen.
ENT TEL ENT VIW TEL ESC ENT TEL VIW ESC VIW ESC - Aile-thro Press the direction button to select aile – thro line and press the ENT button to access the aile – thro function. The value 0% is highlighted then press the direction button to adjust the desired value. press - Rudd-thro Press the direction button to select rudd – thro line and press the ENT button to access the rudd – thro function. The value 0% is highlighted then press the direction button to adjust the desired value.
press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL VIW ESC - Swash lim Press the direction button to select the swash lim mixing then press the ENT button to access the function. off of the swash lim value is highlighted. Press the direction button to adjust the desired the gain then press the ESC button to remove the highlight.
ENT ENT TEL TEL VIW VIW ESC ESC press - Governor 8ch Press the direction button to select the governor 8ch then press the ENT button to access the function. The value no of is highlighted. You may select yes or no by the direction button. Press the ESC button to remove the highlight. ENT TEL press press ENT TEL ENT TEL VIW ESC VIW ESC VIW ESC ENT TEL ENT TEL VIW ESC VIW ESC 9.
press ENT TEL ENT VIW TEL ESC press press ENT TEL VIW ESC ENT VIW TEL ESC VIW ESC press press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC press press ENT TEL VIW ESC VIW ESC press press ENT TEL VIW ESC press ENT TEL VIW ESC press 46 ENT TEL VIW ESC
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT VIW TEL ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press VIW ESC press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT VIW TEL ESC VIW ESC press - ASY To adjust the different value for the master channel, press the direction button to highlight the ASY from the SYM then press the ENT button to highlight the trv value in the right.
press ENT TEL ENT VIW TEL ESC ENT TEL VIW ESC - SEL Press the direction button to select the offset line then the STO is highlighted. Press the direction button to select the SEL then press the ENT button to highlight the offset value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. 10. Swash mix (Helicopter) The Swash mix adjusts the amount and direction of travel for the aileron, elevator and pitch functions.
ENT TEL VIW ESC press - Batt type Press the direction button to highlight the basic sett then press the ENT button to access the Batt type line. Press the ENT button to highlight the value then press the direction button to adjust the value. Press the ESC button to remove the highlight. You may select the function of which you wish to adjust the value by pressing the direction button. press ENT TEL VIW ENT ESC TEL VIW ESC ENT TEL press VIW ENT ESC TEL VIW ESC 11.
- Batt warning Press the direction button to access the Batt warning line then press the ENT button to highlight the value. Press the direction button to adjust the value. Press the ESC button to remove the highlight. - Touch sense The same method is used to access the function and adjust the value with Batt type programming.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT ENT TEL TEL VIW ESC VIW ESC press press ENT TEL VIW - RF country The same method is used to access the function and adjust the value with Batt type programming. ESC press ENT - Display light The same method is used to access the function and adjust the value with Batt type programming.
ENT TEL ENT VIW TEL ESC press ENT TEL VIW ESC VIW ESC press - Beep volume The same method is used to access the function and adjust the value with Batt type programming. press - Voice volume The same method is used to access the function and adjust the value with Batt type programming.
press ENT TEL ENT VIW TEL ESC VIW ESC press 12. Fail safe (AIRCRAFR and Helicopter) ENT TEL VIW ESC When you bind your transmitter, you are programming the receiver with failsafe defaults. If connection is lost between the transmitter and receiver, the receiver immediately operates in those preprogrammed default positions.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL 13. Trainer (Aircraft and Helicopter) VIW ESC press ENT TEL VIW ESC press press ENT TEL VIW ESC The mz-12 has the trainer function. The function activates when you select Teacher, Pupil and Normal mode. You may use this function by wireless and wired. - The teacher mode programming setup Press the direction button to highlight the teach pupil then press the ENT button to access the function.
press press ENT TEL ENT VIW TEL ESC VIW ESC ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL VIW ESC ENT TEL VIW - The pupil mode programming setup After selecting the n/a in the BIND, press the ENT button then bind to the teacher transmitter. The pupil transmitter doesn’t need to program the other value.
16. SETTING & DATA VIEW 15. Telemetry Telemetry is used to perform HoTT telemetry programming setup and check HoTT telemetry data. 4 functions of SETTING & DATA VIEW, SENSOR SELECT, RF STATUS VIEW and VOICE TRIGGER are available. Press TEL button to go to the start up page of telemetry. SETTING & DATA VIEW has been selected on the start up page. Whenever your press DOWN button, 4 functions is selected in turn.
16-2. RX SERVO This function allows you to perform servo programming set up at the entries of OUTPUT CH REVERSE, CENTER, TRIM, LIMIT-, LIMIT+, PERIOD. Press the direction button on RX DATA VIEW mode to access to RX SERVO then press DOWN button to select the desired article. Press ENT button to highlight the value on the selected article, you may change to the desired value. ENT TEL VIW ENT TEL VIW ESC press - REVERSE It is used to decide the direction of servo rotation.
- CENTER The value of servo center in the selected channel at OUTPUT CH can be programmed. The center value depends on transmitter throttle and trim position. General servo center value is 1500us. Press DOWN button to access to CENTER line then press ENT button to highlight the default value 1500usec. Move and hold transmitter throttle at the desired position then press ENT button, the center value corresponding to throttle position is set.
press press ENT TEL ENT VIW TEL ESC ENT ENT TEL TEL VIW press press press ENT ENT TEL TEL VIW ENT ENT TEL TEL VIW ENT TEL VIW ESC VIW ESC ESC - PERIOD The servo response time for transmitter throttle can be adjusted. All channels that servo connected are applied separately. Press DOWN button to access to PERIOD line then press ENT button to highlight the default value 20msec. Press UP/DOWN button to set 10msec or 20msec and then press ENT button to remove the highlight.
ENT TEL VIW ESC press - MODE It is failsafe mode and HOLD/ FAIL SAFE/ HOLD are available. Press DOWN button to access to MODE line then press ENT button to highlight the default value HOLD. Press UP/DOWN button to select the desired value then press ENT button to remove the highlight.
- F.S.POS. It is used to set fail safe position at the desired channel that you select on OUTPUT CH. Press DOWN button to access to F.S. Pos line then press ENT button to highlight the default value 1500usec. Press UP/DOWN button to select the desired value then press ENT button to remove the highlight. - DELAY This function allows you to set the time that failsafe takes to start under failsafe situation Press DOWN button to access to DELAY line then press ENT button to highlight the default value 0.75sec.
- FAIL SAFE ALL It is used when you change failsafe position value of all channels. You need set all channels to FAIL SAFE to use this function. Press DOWN button to access to FAIL SAFE ALL line then press ENT button to highlight the default value NO. Move and hold transmitter throttle at the desired position then press ENT button, the failsafe value corresponding to throttle position is set.
- MASTER CH Master CH in FREE MIXER can be selected. Press DOWN button to access to MASTER CH line then press ENT button to highlight the default value 00. Press UP/DOWN button to select the desired channel then press ENT button to remove the highlight. - SLAVE CH Slave CH in FREE MIXER can be selected. Press DOWN button to access to SLAVE CH line then press ENT button to highlight the default value 00. Press UP/DOWN button to select the desired channel then press ENT button to remove the highlight.
- S-TRAVEL + / The maximum servo travel that is connected to slave channel can be programmed. Press DOWN button to access to S- TRAVEL+/- line then press ENT button to highlight the default value 00. Press UP/DOWN button to select the desired channel then press ENT button to remove the highlight.
press ENT TEL ENT VIW TEL ESC VIW ESC press press press ENT ENT TEL TEL VIW VIW ESC ESC ENT TEL ENT TEL VIW ESC VIW ESC press press ENT TEL 16-5. RX CURVE VIW ESC Perform the exponential programming setup at RX CURVE mode. You may program the exponential value of channel 2,3,4. The default setup is B curve that leads Servo responds proportionally depending on transmitter throttle movement. A curve leads that Servo responds sensitively and C curve leads that Servo responds softly.
press 16-6. RX SERVO TEST ENT It used to perform servo test and program the voltage of receiver power, the max/min temperature of receiver CH OUT TYPE of receiver. Press UP/DOWN buttons to select the desired line and press ENT button then the default value is highlighted. Press UP/DOWN buttons to set the desired value and press ENT button to remove the highlight.
press press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC press press press ENT TEL ENT VIW TEL ESC ENT VIW TEL ESC - ALARM TEMP + / - : Temperature warning If receiver temperature is out of the preset temperature, transmitter repeats a beep warning. Press DOWN buttons to access to ALARM TEMP and press ENT button then the default value is highlighted. Press UP/DOWN buttons to set the desired value and press ENT button to remove the highlight.
press ENT TEL ENT VIW TEL ESC ENT TEL VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC press press ENT TEL VIW ESC press ENT TEL VIW ESC press ENT TEL VIW ESC 68 VIW ESC CH OUT TYPE You may decide the signal output type of receiver. 5 types of ONCE / SAME / SUMO12/ SUMI / SUMD HD12 are available. - ONCE It is use for analogue servo. If ONCE is selected, PERIOD on RX SERVO is set to 20msec automatically. - SAME It is use for digital servo.
ENT TEL VIW ENT ESC press TEL VIW ESC press press press ENT TEL VIW ENT ESC TEL VIW ESC ENT TEL VIW ESC ENT TEL press VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC press ENT TEL 17. SENSOR SELECT It is used to program telemetry sensor that is connected to HoTT receiver. The sensor should be connected to the telemetry pin of receiver to use voice function, warning and the telemetry data information.
press press ENT ENT TEL TEL VIW VIW ESC ESC ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL ESC ENT TEL 19. VOICE TRIGGER VIW VIW It is used to program the sensors related with voice function. The default article REPEAT, TRIG, VARIO, TRANSSMITTER, RECEIVER are available and the optional sensors could be attached. If the optional sensor is connected, it is need to add the function for the optional sensor at SENSOR SELECT mode then VOICE TRIGGER article is created.
press ENT ENT TEL TEL VIW press ENT TEL VIW ESC ENT TEL VIW ESC - TRIG You may designate the switch for the voice functions of transmitter and receiver and the voice functions are changed in turn whenever the switch is on/off. Press DOWN buttons to access to TRIG and press ENT button then the popup message “push desired switch into position on” is appeared. Operate the switch to be used as TRIG on/ off, that switch is designated as TRIG on/off.
- VARIO You may set the on/off switch of vario module for voice function. Press DOWN buttons to access to VARIO and press ENT button then the popup message “push desired switch into position on” is appeared. Operate the switch to be used as VARIO on/off, that switch is designated as VARIO on/off. Voice function is operated when the switch is on.
- RECEIVER You may program the telemetry voice function of receiver, TEMP, STRENGTH, RX VOLT, LOWVOLT, Press DOWN buttons to go to RECEIVER line and press ENT button to access to RECEIVER setup mode. All voice function of TEMP, STRENGTH, RX VOLT, LOWVOLT have been set to use. Press the direction button to select the desired line and press ENT button to unmark the box if you don’t want to use voice function for the desired line.
ENT ENT TEL TEL VIW VIW ESC ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT TEL ENT VIW TEL ESC ENT ENT TEL VIW ESC TEL VIW VIW ESC ESC press press ENT TEL ENT VIW TEL ESC press VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC 74
ENT TEL VIW ESC press ENT TEL VIW ESC press EN 62479:2010 EN 60950-1:2006/A11:2009/A1:2010/A12:2011 EN 301 489-1 V1.9.2 EN 301-489-17 V2.2.1 EN 300 328 V1.7.
• NOTE • Caution This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
mz-12
