User's Manual
9
When you bind your transmitter, you are programming the receiver with failsafe defaults. Graupner/SJ
receiver has 4 Failsafe modes: FAILSAFE, HOLD, OFF and STANDARD.
1-1. Switch on the receiver and place transmitter RF
TRAINER SWITCH at normal position. Press and hold the
MODE button and switch on the transmitter. The Graupner/SJ
logo repeat to blink a single red with a single beep, indicating
that you entered the failsafe mode. Every time you press MODE
button at failsafe mode, the 4 modes are changed in turns.
1-2. Failsafe mode
- FAILSAFE
Move the control sticks on the transmitter to the desired preset failsafe positions. Press & hold the
MODE button for over 2 sec and release the button. The Graupner/SJ logo turns solid red, indicating
the failsafe mode has been set. Conrm the failsafe setting is correct by turning off the transmitter.
The throttle should go to the preset position.
- HOLD
Enter hold mode by pressing MODE button once from the failsafe mode. The Graupner/SJ logo
repeats to blink twice red with twice beep. Press & hold the MODE button for over 2 sec and release
the button. The Graupner/SJ logo turns solid red, indicating the hold mode has been set. If you lose
connection, all channels hold the last given command.
- OFF
Enter off mode by pressing MODE button once from the hold mode. The Graupner/SJ logo repeats
to blink 3 times red with 3 times beep. Press & hold the MODE button for over 2 sec and release
the button. The Graupner/SJ logo turns solid red, indicating the off mode has been set. Even if you
lose connection, the failsafe is not working.
- STANDARD
Enter standard mode by pressing MODE button once from the hold mode. The Graupner/SJ logo
repeats to blink 4 times red with 4 times beep. Press & hold the MODE button for over 2 sec and
release the button. The Graupner/SJ logo turns solid red, indicating the standard mode has been
set. standard features that the throttle channel ( channel Number 1 ) is move into low throttle
position and other channels hold last given command.
The mz-10 has the trainer function. The function activates when you select Teacher, Pupil and
Normal mode by RF TRAINER SWITCH.
1). Mode setting
1-1. Teacher setting
Move transmitter’s RF TRAINER SWITCH of the TEACHER transmitter to TEACHER position.
Press & hold the MODE button and switch on the transmitter. The Graupner/SJ logo repeats to
blink twice red with twice beeps, indicating that you set TEACHER Mode. After two beeps sound
twice, two beeps don’t sound. Now the mz-10 can bind and control all channels of the pupil’s trans-
mitter without restriction.
11. RF Trainer
Normal
Pupil
Teacher
Repeating that the Graupner/SJ logo blinks a single red with a single beep
Repeating that the Graupner/SJ logo blinks twice red with twice beeps
Repeating that the Graupner/SJ logo blinks three times red with three times beeps
Repeating that the Graupner/SJ logo blinks four times red with four times beeps
STANDARD
OFF
HOLD
FAILSAFE
Mode
Button
Once
Once more
Once more
LED status and beep
Function setting LED Description
DELTA
2 AILE
DELTA and 2 AILE
Green LED On
Delta wing function is activated,
2 Aile and V-tail functions are de-activated.
2 Aile function is activated,
Delta and V-tail functions are de-activated.
V-tail function is activated,
Delta and 2 aile functions are de-activated.
Green LED On
2 Green LED On
NOTICE
You may select only 1 function of delta, 2 aile and V-tail
When mz-10 is switched on, the status LED of each function that you set is turned on for 5
seconds to indicate which function has been set.
Failsafe setting could be only set in case that RF TRAINER SWITCH
is at normal ight position
NOTICE
10. FailSafe