No. S1002 OPERATING INSTRUCTION Prior to use, please read this manual thoroughly. Keep this manual in a convenient place for quick and easy reference.
Contents • Before Use • Support and Service - Customer support - Internet sales site - A/S regulation - Warranty regulation • Openhobby A/S Center 1. Box Contents 2. Safety Notes 3. Features 4. Transmitter Control Identification 5. Specification 6. Display Explanation 7. Adjustble Stick Length 8. Adjustble Stick Testion 9. Mode exchange of throttle stick for Mode 1 and Mode 2 10. What is HoTT 11. Battery Installation 12.
• BEFORE USE 2. FLYING SAFETY Thank you for purchasing mz-12 HoTT 2.4GHz Radio System. This system is extremely versatile and may be used by beginners and pros alike. In order for you to make the best use of your system and to fly safely, please read this manual carefully. If you have any difficulties while using your system, please consult the manual, our online Frequently Asked Questions (on the web pages referenced below), your hobby dealer, or the Graupner/SJ Service Center.
. TRANSMITTER CONTROL IDENTIFICATION ANTENNA TX HANDEL S4 SWITCH R F T R AIN ER SW IT C H S2 SWITCH DIAL VOLUME S1 SWITCH S3 SWITCH BATTERY COVER NECKSTRAP LUG ELEV/RUDO STICK ELEV/TRIM THRO/AILE STICK THRO TRIM POWER SWITCH RUDD TRIM AILE TRIM DIRECTION BUTTON ENT, ESC, TEL VIEW BUTTON EAR PHONE CHARGE SOCKET DATA PIN 4
. SPECIFICATION 7. ADJUSTBLE STICK LENGTH Transmitter mz-12 Frequency band Modulation Output power Current drain Operating voltage 2.4~2.4835GHz FHSS 100mW Approx 125mA 3.4V~6V Receiver GR-16 2.4~2.4835GHz FHSS Approx 70mA 3.6V~8.4V The control stick is consisted of 2pc of stick levers and it allows you to adjust the control stick’s length as you want. 1. Hold the lever “B” and turn the lever “A” counter clockwise. Lever “B” The lock will be released. 2.
9.
9 Assemble the centering cam into the throttle gimbal of mode 1 transmitter and set the spring in the center control part and the centering cam with tweezers 10 Screw the disassembled tension control bolt from the elevator gimbal of mode 1 transmitter into the throttle gimbal and adjust the bolt for the desired control 10. WHAT IS HoTT HOPPING TELEMETRY TRANSMISSION(HoTT) it is Graupner/SJ’s unique telemetry technology in 2.
press 12. BINDING ENT You must bind the receiver to the transmitter before the receiver will operate. Binding teaches the receiver the specific code of the transmitter so that it will only connect to it’s corresponding transmitter. TEL VIW ESC 1. With the transmitter on and the home screen displayed, press the ENT button. press ENT TEL ENT TEL VIW ESC VIW ESC 4. After completing the bind, press the ESC button to return to the home screen. 2.
press ENT ENT TEL TEL VIW VIW ESC ESC press press press ENT TEL ENT VIW TEL ESC VIW ESC press - Select model In the home screen, press the ENT button then the model mem is highlighted. Press the ENT button to access the function. ENT TEL press VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC Press the direction button to select the model then press the ENT button to access the Sel model type screen.
press ENT TEL VIW ESC - Clear model When the model mem is highlighted, press the ENT button then the cursor is on the select model line. Press the direction button to select the clear model line then press the ENT button to access to the function. Press the direction button to highlight the model that you wish to clear then press the ENT button. The popup message “YES or NO” appears on the screen. Press the direction button to highlight YES then press the ENT button to clear the model.
- Copy mod->mod The model mem is highlighted in the menu screen then press the ENT button. The cursor is on the select model line. Press the direction button to select the copy mod ->mod line then press the ENT button to access to the function. When the copy from model screen appears, press the direction button to highlight the model you want to copy then press the ENT button to accept.
With the transmitter and the home screen displayed, press the ENT button. Press the direction button to highlight the m.type quick then press the ENT button to access. The model type is selected then press the ENT button to select the motor at C1. Press the ENT button again to highlight the value in the motor at C1 then press the direction button to select the desired value. 4 values ( no, no/inv , idel re, idel fr) as explained below are available.
- Motor at C1 idel fr The idle position of the throttle stick (C1) is forward, away from the user, if the throttle stick is not there, the throttle warning message “Throttle too high” appears and the cut off option is activated. press ENT TEL TEL VIW ESC ENT VIW ESC WARNING : E nsure that any internal-combustion engine or electric motor shouldn’t be running accidentally during the programming process. Press the direction button to select the value,+150%,.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT TEL ENT VIW TEL ESC - Tail type Use the Tail type functions to program the tail mix to match your airplane. 4 tail types (normal, V tail, delt/flw, 2elev sv appear) are available. The correct value should be matched each other since the some value is not match to the others, refer to the below table.
ENT TEL ENT VIW TEL ESC VIW ESC press press press ENT ENT TEL TEL VIW ENT TEL VIW ESC press ENT TEL VIW ESC press - Quick link sett T he quick link sett function allows to adjust the D/R expo value and assign the corresponding switch to cope with the unexpected situation such as the flight with the strong wind. Since the adjusted value is activated by moving the switch, you can cope with the crisis with just one switch. It makes you operating the flight much easier.
ENT TEL VIW - Quick link trim Use the quick link trim function to program the appropriate trims of the quick 2 and quick 3 in the quick link. The user can program the trim in advance to cope with the unexpected situation such as the flight with the strong wind and match the flight situation of the takeoff , thermal and speed of the glider. If the switch is ON, the corresponding trim is activated so the user do not need to set these trims every time.
ENT TEL ENT VIW TEL ESC press press press ENT TEL VIW ESC ENT VIW TEL ESC VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC press After completing the normal quick link adjustment, press the direction button to select the thermal quick link line. The thermal quick link and speed quick link can be programmed in the same method. If you already set the quick link switch and the switch is ON, the cursor is automatically moved to the corresponding quick link value.
press 2-1. Model type (Helicopter) : 5 functions are available Swashplate Use the swashplate function to set the swahplate type to match your Helicopter model. It supports 6 value (1servo, 2 servo,3sv(2rol),3sv(140),3sv(2nic),4sv(90)) Cut off The cut off function allows to turn off the internal combustion engine or the electric motor. Rotor direct Use the rotor direct function to set the rotation direction of the main rotor.
ENT TEL VIW Press the direction button to select +150% in the value. Place the throttle stick at the desired position and press the ENT button then adjusted value is applied (The adjusted value is activated when the throttle stick is in that position). NOTE : the value of +150% is the throttle stick position where the cut off function is activated.
ENT TEL VIW ESC - Pitch min Use the pitch min function to reverse the servo direction in all of pitch, elevator, aileron and throttle channels, the default value is rear. Available settings are rear and front. Press the direction button to select the pith min line then press the ENT button to highlight the pitch min value. Press the direction to select the desired value (rear or front) then press the ESC button to remove the highlight.
press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT VIW TEL ESC VIW ESC press ENT ENT TEL TEL VIW VIW ESC ESC press - Quick link sett The quick link sett function allows to adjust the quick2 value and assign the corresponding switch to cope with the unexpected situation such as the flight with the strong wind. Since the adjusted value is activated by moving the switch, you can cope with the crisis with just one switch.
ENT TEL ENT VIW TEL ESC ENT TEL VIW ESC press ENT TEL VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC 3. Servo sett (Aircraft and Helicopter) The servo sett adjusts the servo reverse, center, travel for all six channels. - Rev : used to reverse the servo direction for all channels. - Cent : u sed to set the neutral position of the servo. - Trv : used to increase or decrease the moving angle of the servo travel.
press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW ESC press press ENT ENT TEL VIW ESC TEL VIW VIW ESC ESC press press press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC press VIW ESC press 23
press ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC VIW ESC 4. Cont sett (Aircraft and Helicopter) It contains 3 categories: model type, quick link set and quick link trim. You can program the 5 and 6 channels in mz-12 to the special function that you want. Typically, the 5 channel is used for the on/ off switch of the retractor gear and the 6 channel is used for the on/off switch of the flap function.
ENT TEL VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC - Cont sett (Helicopter) The basic setting of the Helicopter cont sett is NO.5 gyro, NO6. Throttle, Lim. DV (Digital volume). Generally, this function is seldom used, but Lim.
5. D/R expo (Aircraft and Helicopter) ENT The basic setting of the Helicopter cont sett is NO.5 gyro, NO6. Throttle, Lim. DV (Digital volume). Generally, this function is seldom used, but Lim. DV (Digital volume) can control the operation range of digital volume -100 ~ +100. If DV is programmed, throttle channel is operated only programmed range. TEL press - D/R Affects the overall travel which in turn affects control response sensitivity equally throughout the range of that channel.
press ENT TEL VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC • Timer The mz-12 has four stick modes with the two dual axis sticks. The user can select one among the four default stick modes the default mode is the mode 1. • Receiv out For the maximum flexibility of the receiver socket assignment, the mz-12 provides to swap over the servo outputs 1 to max.6. If you try to use more than 1 servos at the aileron or the elevator or the rudder, the receiver output socket can be assigned as you intend.
- Stick mode Enter the stick mode from the RF sett on the menu. Press the ENT button to highlight the value then press the direction button to select the mode number of 4 modes.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC - Receiv out Press the direction button to select the receiv out line then press the ENT button to access the function. The cursor is on the arrow mark then press the ENT button to access the function.
press ENT TEL VIW ESC ENT TEL VIW ESC - RF transmit RF transmit function allows to turn ON/OFF the RF power output. Press the direction button to select the RF transmit then press the ENT button to select ON or OFF. press ENT TEL VIW ESC ENT TEL VIW ESC press ENT TEL VIW ESC press ENT TEL VIW ESC 30 7. wing mix (AIRCRAFT) Diff aile The diff aile mixing allows to overcome the adverse yaw when the Aircraft is deflected.
- Diff aile Press the ENT button to access the diff aile mixing then press the ENT button again to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears. Move the switch then the corresponding value appears (The diff aile mixing is on/off when the switch is moved).
press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT ENT TEL TEL VIW ENT TEL VIW ESC ESC ENT VIW TEL ESC VIW ESC press - Ail->rudd Press the direction button to select the ail -> rudd line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT TEL ESC VIW ESC VIW press press press ENT TEL ENT TEL VIW ESC VIW ESC press ENT TEL ENT TEL VIW ESC VIW ESC press press ENT ENT TEL VIW TEL VIW ESC ESC ENT TEL - Brak->elev Press the direction button to select the brak -> elev line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight.
- Brak->flap Press the direction button to select the brak -> flap line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears. Move the switch then the corresponding value appears (The brak -> flap mixing is on/off when the switch is moved).
press ENT TEL ENT VIW TEL ESC ENT TEL ENT VIW TEL ESC ENT TEL VIW ESC VIW ESC - Elev->flap Press the direction button to select the elec -> flap line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button. The popup message “push desired switch into position on” appears.
ENT ENT TEL TEL VIW VIW ESC ESC press press press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT TEL VIW ESC ENT TEL VIW ESC - Flap->elev Press the direction button to select the flap -> elev line and press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. Press the direction button to select the hyphen then press the ENT button.
ENT TEL ENT VIW TEL ESC press VIW ESC press ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC ENT TEL VIW ESC - Diff-red Press the direction button to access the diff-red mixing then press the ENT button to highlight the value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. press ENT TEL VIW ESC 8.
- Ptch Press ENT button to access the ptch mixing then press the ENT button again to access the function. -100% of the point 1 value is highlighted. Move the throttle stick to the high position step by step then the point 2,3,4,5 is selected in turn. After selecting the point number, press the direction button to adjust the desired value. Press the ESC button to return to the previous screen.
ENT ENT TEL TEL VIW VIW ESC ESC press ENT - Pitc->thro Press the direction button to select pitc->thro line and press the ENT button to access the pitc>thro function. 0% of the point 1 value is highlighted. Move the throttle stick to the high position step by step then the point 2,3,4,5 is selected in turn. After selecting the point number, press the direction button to adjust the desired value. Press the ESC button to return to the previous screen.
ENT TEL ENT VIW TEL ESC - Pitc->rudd ruddPress the direction button to select pitc->tail line and press the ENT button to access the pitc-> tail function. 0% of the point 1 value is highlighted. Move the throttle stick to the high position step by step then the point 2,3,4,5 is selected in turn. After selecting the point number, press the direction button to adjust the desired value. Press the ESC button to return to the previous screen.
ENT TEL ENT VIW TEL ESC ENT TEL VIW ESC VIW ESC - Aile-thro Press the direction button to select aile – thro line and press the ENT button to access the aile – thro function. The value 0% is highlighted then press the direction button to adjust the desired value. press ENT - Rudd-thro Press the direction button to select rudd – thro line and press the ENT button to access the rudd – thro function. The value 0% is highlighted then press the direction button to adjust the desired value.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL VIW - Swash lim Press the direction button to select the swash lim mixing then press the ENT button to access the function. off of the swash lim value is highlighted. Press the direction button to adjust the desired the gain then press the ESC button to remove the highlight.
ENT TEL ENT VIW TEL ESC VIW ESC press - Governor 8ch Press the direction button to select the governor 8ch then press the ENT button to access the function. The value no of is highlighted. You may select yes or no by the direction button. Press the ESC button to remove the highlight. ENT TEL VIW ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW VIW ESC ESC press 9.
press ENT TEL ENT VIW TEL ESC press press ENT TEL VIW ESC ENT VIW TEL ESC VIW ESC press press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC press press ENT TEL VIW ESC VIW ESC press press ENT TEL VIW ESC press ENT TEL VIW ESC press 44 ENT TEL VIW ESC
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT VIW TEL ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press VIW ESC press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL ENT VIW TEL ESC VIW ESC press - ASY To adjust the different value for the master channel, press the direction button to highlight the ASY from the SYM then press the ENT button to highlight the trv value in the right.
press ENT ENT TEL TEL VIW ENT TEL 10. Swash mix (Helicopter) VIW ESC - SEL Press the direction button to select the offset line then the STO is highlighted. Press the direction button to select the SEL then press the ENT button to highlight the offset value. Press the direction button to adjust the desired value then press the ESC button to remove the highlight. The Swash mix adjusts the amount and direction of travel for the aileron, elevator and pitch functions.
ENT TEL VIW ESC - Batt type Press the direction button to highlight the basic sett then press the ENT button to access the Batt type line. Press the ENT button to highlight the value then press the direction button to adjust the value. Press the ESC button to remove the highlight. You may select the function of which you wish to adjust the value by pressing the direction button. press press ENT TEL ENT VIW TEL ESC press ENT TEL VIW ESC ENT VIW TEL ESC VIW ESC 11.
- Batt warning Press the direction button to access the Batt warning line then press the ENT button to highlight the value. Press the direction button to adjust the value. Press the ESC button to remove the highlight. - Touch sense The same method is used to access the function and adjust the value with Batt type programming.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT TEL - RF country The same method is used to access the function and adjust the value with Batt type programming. VIW ESC press ENT TEL VIW ESC - Display light The same method is used to access the function and adjust the value with Batt type programming.
ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL ENT VIW TEL ESC VIW ESC press press - Voice volume The same method is used to access the function and adjust the value with Batt type programming. - Beep volume The same method is used to access the function and adjust the value with Batt type programming.
press ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL ENT VIW TEL ESC VIW ESC ENT TEL VIW ENT ESC TEL VIW ESC press press 12. Fail safe (AIRCRAFR and Helicopter) ENT When you bind your transmitter, you are programming the receiver with failsafe defaults. If connection is lost between the transmitter and receiver, the receiver immediately operates in those preprogrammed default positions.
press ENT ENT TEL TEL VIW VIW ESC ESC press ENT ENT TEL TEL VIW VIW ESC ESC press ENT TEL VIW ESC 13. Trainer (Aircraft and Helicopter) press ENT TEL VIW ESC press press ENT TEL The mz-12 has the trainer function. The function activates when you select Teacher, Pupil and Normal mode. You may use this function by wireless and wired. VIW ESC - The teacher mode programming setup Press the direction button to highlight the teach pupil then press the ENT button to access the function.
press press ENT TEL ENT VIW TEL ESC VIW ESC ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL VIW ESC ENT TEL VIW - The pupil mode programming setup After selecting the n/a in the BIND, press the ENT button then bind to the teacher transmitter. The pupil transmitter doesn’t need to program the other value.
15. Telemetry 16. SETTING & DATA VIEW Telemetry is used to perform HoTT telemetry programming setup and check HoTT telemetry data. 4 functions of SETTING & DATA VIEW, SENSOR SELECT, RF STATUS VIEW and VOICE TRIGGER are available. Press TEL button to go to the start up page of telemetry. SETTING & DATA VIEW has been selected on the start up page. Whenever your press DOWN button, 4 functions is selected in turn.
16-2. RX SERVO This function allows you to perform servo programming set up at the entries of OUTPUT CH REVERSE, CENTER, TRIM, LIMIT-, LIMIT+, PERIOD. Press the direction button on RX DATA VIEW mode to access to RX SERVO then press DOWN button to select the desired article. Press ENT button to highlight the value on the selected article, you may change to the desired value. ENT TEL VIW ENT TEL VIW ESC press - REVERSE It is used to decide the direction of servo rotation.
press - CENTER The value of servo center in the selected channel at OUTPUT CH can be programmed. The center value depends on transmitter throttle and trim position. General servo center value is 1500us. Press DOWN button to access to CENTER line then press ENT button to highlight the default value 1500usec. Move and hold transmitter throttle at the desired position then press ENT button, the center value corresponding to throttle position is set.
press press ENT TEL ENT VIW TEL ESC ENT ENT TEL TEL VIW press press press ENT ENT TEL TEL VIW ENT ENT TEL TEL VIW ENT TEL VIW ESC VIW ESC ESC - PERIOD The servo response time for transmitter throttle can be adjusted. All channels that servo connected are applied separately. Press DOWN button to access to PERIOD line then press ENT button to highlight the default value 20msec. Press UP/DOWN button to set 10msec or 20msec and then press ENT button to remove the highlight.
ENT TEL VIW - MODE It is failsafe mode and HOLD/ FAIL SAFE/ HOLD are available. Press DOWN button to access to MODE line then press ENT button to highlight the default value HOLD. Press UP/DOWN button to select the desired value then press ENT button to remove the highlight.
- F.S.POS. It is used to set fail safe position at the desired channel that you select on OUTPUT CH. Press DOWN button to access to F.S. Pos line then press ENT button to highlight the default value 1500usec. Press UP/DOWN button to select the desired value then press ENT button to remove the highlight. - DELAY This function allows you to set the time that failsafe takes to start under failsafe situation Press DOWN button to access to DELAY line then press ENT button to highlight the default value 0.75sec.
- FAIL SAFE ALL It is used when you change failsafe position value of all channels. You need set all channels to FAIL SAFE to use this function. Press DOWN button to access to FAIL SAFE ALL line then press ENT button to highlight the default value NO. Move and hold transmitter throttle at the desired position then press ENT button, the failsafe value corresponding to throttle position is set.
- MASTER CH Master CH in FREE MIXER can be selected. Press DOWN button to access to MASTER CH line then press ENT button to highlight the default value 00. Press UP/DOWN button to select the desired channel then press ENT button to remove the highlight. - SLAVE CH Slave CH in FREE MIXER can be selected. Press DOWN button to access to SLAVE CH line then press ENT button to highlight the default value 00. Press UP/DOWN button to select the desired channel then press ENT button to remove the highlight.
- S-TRAVEL + / The maximum servo travel that is connected to slave channel can be programmed. Press DOWN button to access to S- TRAVEL+/- line then press ENT button to highlight the default value 00. Press UP/DOWN button to select the desired channel then press ENT button to remove the highlight.
press ENT TEL ENT VIW TEL ESC VIW ESC press press press ENT ENT TEL TEL VIW VIW ESC ESC ENT TEL ENT TEL VIW ESC VIW ESC press press ENT TEL VIW ESC 16-5. RX CURVE Perform the exponential programming setup at RX CURVE mode. You may program the exponential value of channel 2,3,4. The default setup is B curve that leads Servo responds proportionally depending on transmitter throttle movement. A curve leads that Servo responds sensitively and C curve leads that Servo responds softly.
press 16-6. RX SERVO TEST ENT TEL It used to perform servo test and program the voltage of receiver power, the max/min temperature of receiver CH OUT TYPE of receiver. Press UP/DOWN buttons to select the desired line and press ENT button then the default value is highlighted. Press UP/DOWN buttons to set the desired value and press ENT button to remove the highlight.
press press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL ENT VIW TEL ESC VIW ESC press press press ENT TEL ENT VIW TEL ESC ENT TEL ENT VIW TEL ESC - ALARM TEMP + / - : Temperature warning If receiver temperature is out of the preset temperature, transmitter repeats a beep warning. Press DOWN buttons to access to ALARM TEMP and press ENT button then the default value is highlighted. Press UP/DOWN buttons to set the desired value and press ENT button to remove the highlight.
press press ENT TEL ENT VIW TEL ESC VIW ESC ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC press press ENT TEL VIW ESC press ENT TEL VIW ESC 66 CH OUT TYPE You may decide the signal output type of receiver. 5 types of ONCE / SAME / SUMO12/ SUMI / SUMD HD12 are available. - ONCE It is use for analogue servo. If ONCE is selected, PERIOD on RX SERVO is set to 20msec automatically. - SAME It is use for digital servo.
ENT TEL VIW ENT ESC press TEL VIW ESC press press press ENT TEL VIW ENT ESC TEL VIW ESC ENT TEL VIW ESC ENT TEL press VIW ESC ENT TEL VIW ESC 17. SENSOR SELECT press ENT TEL VIW ESC press ENT TEL It is used to program telemetry sensor that is connected to HoTT receiver. The sensor should be connected to the telemetry pin of receiver to use voice function, warning and the telemetry data information.
press press ENT ENT TEL TEL VIW VIW ESC ESC ENT TEL ENT VIW TEL ESC VIW ESC press press ENT TEL VIW ESC ENT TEL VIW ESC 18. RF STATUS VIEW It shows RF status between transmitter and receiver through telemetry function. Press DOWN button to go to RF STATUS VIEW line and press ENT button to access to RF STATUS VIEW mode. You may check RF status at this screen. 19. VOICE TRIGGER It is used to program the sensors related with voice function.
press ENT TEL ENT VIW TEL ESC VIW ESC press ENT TEL VIW ESC ENT TEL VIW - TRIG You may designate the switch for the voice functions of transmitter and receiver and the voice functions are changed in turn whenever the switch is on/off. Press DOWN buttons to access to TRIG and press ENT button then the popup message “push desired switch into position on” is appeared. Operate the switch to be used as TRIG on/off, that switch is designated as TRIG on/off.
- VARIO You may set the on/off switch of vario module for voice function. Press DOWN buttons to access to VARIO and press ENT button then the popup message “push desired switch into position on” is appeared. Operate the switch to be used as VARIO on/off, that switch is designated as VARIO on/off. Voice function is operated when the switch is on.
- RECEIVER You may program the telemetry voice function of receiver, TEMP, STRENGTH, RX VOLT, LOWVOLT, Press DOWN buttons to go to RECEIVER line and press ENT button to access to RECEIVER setup mode. All voice function of TEMP, STRENGTH, RX VOLT, LOWVOLT have been set to use. Press the direction button to select the desired line and press ENT button to unmark the box if you don’t want to use voice function for the desired line.
ENT ENT TEL TEL VIW VIW ESC ESC press press ENT ENT TEL TEL VIW VIW ESC ESC press press ENT TEL ENT VIW TEL ESC ENT ENT TEL VIW ESC TEL VIW VIW ESC ESC press press ENT TEL ENT VIW TEL ESC press VIW ESC press ENT TEL VIW ESC ENT TEL VIW ESC 72
• Safety Approval ENT TEL VIW ESC Declaration of Conformity (in accordance with ISO/IEC 17050-1) press - Product(s): Graupner/SJ mz-12 Transmitter Item Number(s): ENT TEL VIW ESC Equipment class: 2 The objects of declaration described above are in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/ EC: press EN 62479:2010 ENT TEL VIW ESC EN 60950-1:2006/A11:2009/A1:2010/A12:2011 EN 301 489-1 V1.9.
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
No.
