No. S1006 OPERATING INSTRUCTION Prior to use, please read this manual thoroughly. Keep this manual in a convenient place for quick and easy reference.
Contents • Before Use • Introduction • Support and Service • Openhobby A/S Center 1. Box Contents 2. Flying Safety 3. Features 4. Specification 5. Stick tension adjustment 6.Transmitter Control Identification 7. Binding 8. Transmitter Programming Setup 3P 3P 3P 3P 3P 3P 3P 4P 4P 4P 5P 5P BASE MENU (Helicopter, Airplane, Gilder) 1. Model Select 1-1. SEL(Select model) 1-2. NEW(New Model) 1-3. Int.M(INT. Model) 1-4. EXT.M(EXT.Model) 1-5. RES(Model Reset) 1-6. CPY(Model Copy) 2. Model Type 3. E.P.A 4.
• BEFORE USE Thank you for purchasing mz-24 HoTT 2.4GHz Radio System. This system is extremely versatile and may be used by beginners and pros alike. In order for you to make the best use of your system and to fly safely, please read this manual carefully. If you have any difficulties while using your system, please consult the manual, our online Frequently Asked Questions (on the web pages referenced below), your hobby dealer, or the SJ Service Center.
6. TRANSMITTER CONTROL IDENTIFICATION 4. SPECIFICATION ANTENNA DV3 Transmitter mz-24 Receiver GR-24 2.4~2.4835GHz 2.4~2.4835GHz Frequency band Modulation Output power Current drain Operating voltage DV2 DT2 DT1 DV4 DV1 FHSS FHSS S5 SWITCH 100mW - S2 SWITCH approx 125mA approx 70mA S1 SWITCH 3.4V~6V 3.6V~8.4V S3 SWITCH S4 SWITCH POWER SWITCH NECKSTRAP LUG 5.
7. BINDING 1. You must bind the receiver to the transmitter before the receiver will operate. Binding teaches the receiver the specific code of the transmitter so that it will only connect to it’s corresponding transmitter. If you turn on transmitter’s power before binding, the warning message appears on transmitter LCD page, which announce transmitter is not bound. Touch SET icon on warning pop up to access to Tx ctl (BIND) Touch 2.
BASE MENU (Helicopter, Airplane, Gilder) 1. Model select It is used to add or select model. Touch Model Sel icon in base menu to access Model sel menu Touch 1-2. NEW This function is use to create the new model or exchange the current model to others. There is 2 methods of Manual setting and Wizard setting. You may program the basic function sequentially in Manual setting. Here is the example for airplane 1-1. SET Touch the desired MODEL NAME icon then it is activated in blue.
In accordance with model type that you selected, swash type function or wing type function is accessed. Below picture shows the example for wing type in airplane. Select the desired wing type, tail type and power type in turn. If all procedures have been done correctly, all types that you selected appear on the page.
Touch Touch In accordance with model type that you selected, swash type function or wing type function is accessed. Below picture shows the example for swash type in helicopter. Select the desired swash type, power type and set reverse function, EPA function, D/R EXP function, Pit CRV function, Thr.CRV function, GYRO function, Thr.HOLD function, FAILSAFE function in turn. When you touch WIZ icon after completing to program each function, the next step is accessed in turn.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch 9
Touch Touch Touch Touch Touch Touch 1-3. INT.M (Internal Model) It is used to copy the model memory in SD Card into the model list of transmitter. To make use of INT.M function, you need SD Card that has the programmed model file. If you put SD Card into SD Card slot on the back of transmitter, “SD Card” icon is lighted in the transmitter main page. When the icon is lighted, touch the base setup icon to call the base setup page.
1-4. EXT.M (External Model) This function is used to copy the model in transmitter into SD Card. In order to use EXT.M function, you need to plug SD Card into SD Card slot on the back of transmitter. When it is plugged into the slot, “SD Card” icon is lightened in the transmitter main page. Touch Base setup icon to call the base setup page. In the page, touch “Model Select” icon to call the “Model Select” setup page and touch the source model to copy in transmitter then it is activated in blue. Touch “EXT.
2. Model type 1-6. CPY(Model Copy) The Copy function is used to copy the programmed values of a model into the other model. Touch the source model to copy, it is activated in blue. Now touch “CPY” icon on the right bottom and touch the copy destination then it is activated in blue as well. The popup message indicating the destination and source appear. Touch YES, if they are correct, then “Please wait” message is displayed and a few seconds later, the source data is copied to the copy destination.
Touch Touch Touch Touch Touch Touch Touch 3. E.P.A E.P.A is used to adjust Servo operation angle and limitation for each channel. Touch “E.P.A” icon on the base menu page to call E.P.A setup page. “Limit” and “travel” can be set individually. When you touch each icon, it is activated in blue and you may adjust the values with “INC” and “DEC” buttons. Touch NEXT icon on the right to go and set more channels’ E.P.A. after setting each channel’s E.P.A, touch “SERVO” icon to call “SERVO VIEW” page.
Touch Touch Touch Touch Touch Touch 4. Reverse It is used to reverse the operation of an individual servo. Touch the “Reverse” icon in the base menu page to call the Reverse setup page. In “Reverse” page, you are able to reverse the operation of a servo. When you touch the “NOR” icon, “NOR” is changed to REV” and the operation of an individual servo is reversed. Touch “Servo” icon on the left top to call the “Servo View” page after setting “Reverse” function.
Touch Touch Touch Touch Touch Touch 6. THR.CUT This function is used to stop the operation of engine. THR.CUT function works from below one-third position of the full movement range of throttle stick. Touch “THR.CUT” icon in the base menu page to call the “THR.CUT” setup page. When touching “INH” icon in “ACT” line, you may change the value to “OFF”. When touching “On” icon in “CTL”, the message “Select” is popped up.
Touch Touch 7. TX ctl It consists of the multiple functions for a transmitter. It includes “BIND ON/OFF”, “TX OUT SET”, “RF ON/OFF”, “RF TYPE”, “RANG TEST”, and “DSC OUTPUT” functions. Touch “TX ctl” icon to call the “TX ctl” setup page. Touch Touch Touch - BIND ON/OFF Touch Touch It is used to bind a transmitter to a receiver. In “TX ctl” setup page, turn on a receiver and press “Setup” icon of a receiver for over 3 seconds until a receiver is entered the binding mode.
- TX OUT SET It is used to edit the receiver’s “out-channel” connected to each channel of transmitter as you want. For example, when “2 Elevator” function is used, the “CH3” and “CH8” out pins of receiver are used in the traditional channel setup, however, if the receiver’s CH4 pin is set for the transmitter’s CH3 using “TX OUT SET” function, the CH4 and CH3 pin are operated for the “2 ELEVATOR” function. To make use of this function, a receiver should be bound first.
Touch Touch - DSC OUTPUT It is used to set the number of channel when Trainer function is used with DSC jack. If 5 channels are used, PPM5 is recommended to use. To use more than 5 channels, choose the appropriate PPM for each condition. PPM10, PPM16, PPM18, PPM24 are selectable. Whenever you touch the value icon in DSC OUTPUT, You can select “PPM10”, “PPM16”, “PPM18”, and “PPM 24” in turn. Default value is “PPM 10”. - RANGE TEST “Range Test” function reduces the power output.
8. TIMER Timer function may be set for any desired time ,i.e. model time, date, time, etc. Two independent timers, TIMER1 and TIMER2, are provided for each model. Touch “Timer” icon in base menu page to call the timer setup page. Touch Touch In the “Timer” setup page, set “TIMER 1” first. The timer in the first line is used when to save the flight data on SD card. Bind transmitter and receiver and Insert SD card into SD card slot in the rear of transmitter.
Touch Touch Touch Touch After “ALARM” setup, you may set “START SW”. Touch “NULL” icon in “START SW” to call “Select” message popup. Now, move the switch with your choice then this switch is set on/ off switch for “START SW” and the switch direction setup page appears. You may change ON/OFF by touching icons. When the switch is moved to the direction of on, the function is operated. Touch “Back” icon to return TIMER setup page When START SW setup is completed, you may set RESET SW function.
Touch Touch Touch Touch Touch Touch After RESET SW is set, you may set “LAP SW” function. Touch “NULL” icon in “LAP SW” to call “select” message popup. Now, move the switch with your choice then this switch is set on/ off switch for “LAP SW” and the switch direction setup page appears. You may change ON/OFF by touching icons. When the switch is moved to the direction of ON, the function is operated. Whenever the LAP SWITCH is on, Lap time is saved into LAP list.
After Timer 2 setup, touch “NEXT” icon on the right. You may call the page of the date/ time setup. Touch “SET” icon to activate it in blue and touch the desired value to activate in blue. With “INC” and “DEC” buttons, you may adjust the values for the date and time as the picture shown below. BATT TIME and MODEL TIME can be reset by touching the corresponding B.RES and M.RES icons.
Touch Touch Touch Touch Touch Touch Touch 9. FAILSAFE When you bind your transmitter, you are programming the receiver with failsafe defaults. If connection is lost between the transmitter and receiver, the receiver immediately operates in those preprogrammed default positions. The default value is “Hold” and you may select “Hold” or ”F/S” for up to six channels. CAUTION: Fail safe function should be operated when the transmitter and receiver are switched on.
10. TRIM STEP Touch Touch Touch Touch It allows you to check all function values of “Digital trim step”, “DT1”, “DT2”, ‘Digital volume”, and “Side slide”. Touch “Trim Step” icon in base menu page to call Trim Step setup page. The step value indicates the amount that the trim is moved in the range, 100, when operating trim key one time. “4” is set by default and it means that the trim is moved as much as “4” by operating trim key one time.
Touch Touch Touch Touch Touch Touch Touch Touch 11. SERVO It is used to test a servo and check the servo movement in a graph. You are able to test the servo movement from 0.5sec to 5 sec with your choice. Touch “Servo” icon in the base page to call the servo setup page. In the servo setup page, the servo movement of every 12 channels is displayed in graph and figure when transmitter is operated. Touch “View” icon in the right bottom to call “Test” function page.
12. CH Set Touch Touch It is used to set the channel of a transmitter. The basic setup of the transmitter’s channel is set differently depending on 3 different types (“model type”, “wing type”, and “swash type”) and mz-12 offers AUX channel to set the switch, volume, and side lever for your purpose. Touch “CH set” icon on base menu page to call to “CH set” setup page. In “Ch Set” setup page, the basic functions of the transmitter which is connected individually to every channel are displayed.
Touch Touch Touch Touch Touch Touch Touch Touch Touch 13. Out Swap This function is used to edit the channel connection between transmitter and receiver. (It is similar to TX OUT SET function in TX ctl, but Out Swap function is operated without transmitting the setup data to a receiver unlike TX OUT SER function.
1-1 NEW This function is used when you wish to create new Q.LINK. If you may want to set for new Q.LINK, touch the value in “Q.LINK” line to activate it in blue and touch “NEW” icon in the right to call “CTRL” and “DELAY” options. In “CTRL” setup, touch “NULL” icon to call “Select” message popup and move the switch or stick with your choice then the switch or stick is set to Q.LINK switch. To set “DELAY” function, touch “0.0s” icon to activate in blue and set the delay time with “INC” and “DEC” buttons.
Hold Hold ldle-up1 ldle-up1 Touch ldle-up2 ldle-up2 ldle-up3 ldle-up3 Touch Touch Touch Touch Hold ldle-up1 ldle-up2 ldle-up3 1-2 NAM 1-3 CPY It is used when to revise the name of “Q.LINK”. Touch the target value in “Q.LINK” to activate in blue. Now touch “NAM” icon to call NAM setup page. In the page, enter the desired name using the keypad. After that, touch “EN” icon then the revised name is displayed in “New Q.LINK Name”. Now, touch “BACK” icon on the left top left to call “Q.
Touch Touch Touch Touch 2. D/R, EXP 1-4 Del It is used to delete the unused Q.LINK. Touch the entry in Q.LINIK line that you want to delete to activate in blue and touch “DEL” icon. Now, the selected Q.LINK entry is deleted in Q.LINK list. If you touch “NEXT” icon, you may call the next page Touch Touch D/R function is used to adjust the operation range of servos that is connected to all channels including aileron, elevator and rudder channels.
Touch Touch After “D/R”, “EXP” setup, perform CTL setup. It is used to assign the switch to D/R, EXP function Touch “NULL” icon in CTL line to call “Select” message popup and move the switch that you want to use then that switch is set on/ off to switch and the switch direction setup page appears. You may select ON or OFF by touching icons. When the switch is moved to the direction of ON, the function is operated. Touch “Back” icon to return D/R, EXP setup page.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Telemetry 32
3. PIT.CRV This function adjusts the pitch operation curve in relation to the movement of the throttle stick for each condition Since pitch curve is closely related with Q.LINK setup, Q.LINK setup should precede PIT.CRV setup. Call Q.LINK setup page and check Q.LINK setup is completed correctly and touch “BACK” icon to return FUNCTION page. (Refer to the manual on Q.
TRIM TRIM TRIM TRIM Touch Touch Touch Touch TRIM Touch TRIM TRIM TRIM Touch Q.LINK (idel-up2) TRIM TRIM Touch Touch TRIM TRIM Q.
If you touch OFF icon in Curve line, it is changed to ON and the operation curve is smoother. To set the pitch, throttle curve trim, touch “TRIM” icon in the top right to call the pitch, throttle curve trim setup page. Touch TRIM TRIM Touch Touch Touch You may designate throttle curve key with DV1, DV2, DV3, DV4, SL1 and SL2 to set the section curve for the hovering in normal Q.Link and IDLE 1, IDEL 2 Q.Link.
In FUNCTIOPN page, touch “THR.CRV” icon to call THR.CRV setup page. You need to mark the point on graph first and then adjust the operation curve with “DEC”, “INC”, X-axis and Y-axis buttons. Touch “ST OFF” to switch to “ST ON” then the throttle position line appears on graph. Move throttle stick and place the line at the desired position between point “L” and “H” then touch “ENT” icon on the bottom right. Now the new point is marked in graph.
TRIM 워드:63P 63-5W 이미지 수정 TRIM TRIM TRIM Touch Touch Touch TRIM TRIM TRIM TRIM TRIM TRIM Touch Touch TRIM TRIM Touch Touch TRIM TRIM Touch TRIM Touch Telemetry 37
If you touch OFF icon in Curve line, it is changed to ON and the operation curve is smoother. You may set the pitch, throttle curve trim by touching “TRIM” icon in the top right. The setup method is explained at PIT.CRV S NORMAL MODEL NAME 1 TRIM Touch ON HELI 1 HELI 1 TRIM OFF +076% TRIM ON +076% Touch Touch +100% H +080% +082% +080% Touch Y- a x i s Touch Telemetry 5. Gyr/Gover This function is utilized to adjust the mixing of Gyro” and “Governor” for each condition.
Gyro Gain, Governor, Governor RATE, Gyro Suppression are available in this function - Gyro Gain is used to adjust the sensitivity of gyro. “00%” is basically set and heading lock gyro is operated at over 40% of sensitivity. You may adjust sensitivity for each condition of Q.LINK. - Governor ACT is used to select “INH” or “ON” for Governor function. The default value is “INH” and it should be set to “ON” to use Governor ACT by touching “INH” icon.
Touch Gyro Suppression Touch TRIM Telemetry Touch 6. THR.HOLD This function is for powering down an engine or motor using a designated switch. Throttle hold has higher authority than any other flight mode. When you activate THR.HOLD, the throttle channel is driven to its programmed value. It is usually used to turn off an engine or hold in idle position when helicopter’s auto rotation flight Touch In function page, touch “THR.HOLD” icon to call “THR.HOLD” setup page.
Touch Telemetry Touch 7. SWASH Touch The swash function supports adjustment of the travel amount and direction of the aileron, elevator and pitch in Helicopter mode. Bind a helicopter to a receiver and set the travel amount and direction of the swash channels desirably Touch “SWASH” icon to call “SWASH” setup page. When touching the values in PITC, AILE and ELEV, they are activated in blue. You may adjust the values with INC and DEC buttons. The default value is 60%.
8. S.Limt (Swash Limit) It is used to have the channels of PITCH, AILE and ELEV operated for the circle movement of the stick and the channels of PITCH, AILE and EL have the travel limits according to the circle setup size. Servo EPA should be set over 100%, if the circle size is over 100% The Swash rotation function in the bottom is used to make the swash that mz-12 doesn’t support available by rotating the swash angle In the Function page, touch “S.Limit” icon to call “S.Limit” setup page.
A (RATE) B A (RATE) B Touch Touch Touch Telemetry Touch Touch A (RATE) A B (RATE) B Touch Touch Touch A (RATE) B A (RATE) Touch B Touch Touch Touch A (RATE) B A Touch (RATE) Touch B Touch 43
Touch Touch Telemetry Telemetry A (RATE) B (RATE) B Touch 10. THR.MIX Touch THR.MIX function prevents RPM decay when PITCH, AILE and ELEV inputs are given. This mix advances the throttle position with mix control to maintain RPM. This function can be adjusted for each condition of Q.LINK and three types is available (AILE>>THRO, ELEV>>THRO, RUDD>>THRO) AILE>>THRO: It can prevent RPM decay and maintain flight altitude of a helicopter while controlling aileron.
11-1. Liner mixing type In FUNCTION page, touch “Prog.MIX” icon to call the prog.mix page. Touch “INH” icon in ACT line to switch to “ON” and touch “NONE” in MST line to call the mixing channel setup page. Touch and activate “NONE” icon and select the desired channel for the master by touching. Now, touch and activate the left “NONE” icon, it is for Slave channel, and select the desired channel for the slave by touching. Touch “BACK” icon to return to Prog.MIX setup page.
Touch Touch Touch Touch Touch Touch Touch Touch Touch ACT CTL CTL A B B Touch Touch Touch 46
Touch ACT CTL ACT CTL A B A B Touch Touch Touch ACT A Touch CTL ACT CTL ACT CTL B A B A B Touch ACT CTL A B Touch Touch ACT CTL ACT CTL A B A B Touch Touch ACT CTL ACT CTL A B A B Telemetry Touch Touch 47
11-2. Curve mixing type In the prog.mix page, touch “NEXT” icon to call the next page and touch “INH” icon in the cross line of NO7 and ACT to switch to “ON”. Touch “NONE” in MST line to access the channel selection page and touch and activate “NONE” icon to select the desired channel of MST and SLV. Touch “BACK” icon to return to the prog.mix page. Touch “>>” icon to call the program mixing setup page. Now, you need to set CTL function.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch 49
Touch Touch 12. Trainer (Helicopter, Airplane, Gilder) mz-12 features a programmable trainer function. Two transmitters must be connected by Wireless or an optional DSC code. This function makes it possible for the instructor to choose which functions and channels are to be used for instruction. In FUNCTION page, touch “Trainer” icon to call the trainer setup page. The default value, TEACH, is set in all channels which means that this transmitter is Teacher transmitter.
Touch Touch 13. PIT >>RUDD This function is used to correct the unintended movement of rudder during the flight of a helicopter. It is not necessary when you make use of heading lock gyro Touch “PITT >> RUDD” icon in the function page to call PIT >> RUDD setup page. You need to mark the point on graph first and then adjust the operation curve with “DEC”, “INC”, X-axis and Y-axis buttons. Touch “ST OFF” icon to switch to “ST ON” then the pitch position line appears on graph.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Telemetry Touch Touch 14. Telemetry It is used to perform the programming setup and check HoTT telemetry functions. Touch “Telemetry” icon to call the Telemetry page. You may program 5 types of “RX SELECT”, “SETTING & DATA VIEW” “SENSOR SELECT”, ”RF STATUS VIEW”, and “VOCIE TRIGGER”. 14-1. RX SELECT Touch Touch 52 It is used to select a receiver that would transmit the telemetry data to mz-12 when 2 receivers are bound to mz-12.
- RX SERVO Touch The servo functions, “REVERSE”, “CENTER”, “TRIM”,” LIMIT-“, LIMIT+, and “PERIOD”, can be programmed throughout receiver when servo is connected to each channel of receiver. In “RX DATA VIEW” page, touch “ENT” icon to call RX SERVO page. You may move the cursor “>” to other category with INC button and select the category that you want to program. After deciding the desired category, touch “SET” icon to activate in red and adjust the value with INC and DEC buttons.
• CENTER • REVERSE It is used to reverse the operation of an individual servo. Touch “SET” icon to activate “OFF” in red and touch INC and DEC buttons to switch to “ON”. Touch “SET” icon again to deactivate the value and touch INC buttons to move the cursor to “CENTER”. It is used to set the “center position” of servo. Touch “SET” icon to activate the value in red.
• TRIM • LIMIT -, + It is used to set the servo’s “Trim position”. Touch “SET” icon then the values of CENTER and TRIM are activated in red. Adjust TRIM values with INC and DEC buttons and touch “SET” icon again to deactivate the value. Touch INC button to move the cursor to “LIMIT -” The function supports the adjustment of servo’s maximum travel amount for +,- direction.
- RX FAIL SAFE • PERIOD • OUTPUT CH/ INPUT CH It is used to set the speed of receiver’s output signal. Touch “SET” icon to activate the default value, 20msec, in red and set the value to 10msec with INC and DEC buttons. Touch “SET” icon again to deactivate the value and touch ENT button to call “RX FAIL SAFE” setup page You may edit and adjust transmitter channel which is connected with a receiver using “OUTPUT CH” and “INPUT CH”.
Touch • MODE • F.S.POS It is used to select the failsafe type. “HOLD” is basically set in all the channels. Touch “SET” icon to activate the value in red then you may select HOLD or OFF or FAIL SAFE with INC and DEC buttons. After selecting one of HOLD, OFF and FAIL SAFE, touch “SET” icon again to deactivate the value. Touch INC button to move the cursor to “F.S.POS” It is used to decide the servo’s position when FAIL SAFE function is activated.
• FAIL SAFE ALL • DELAY It is used to set the time delay. The failsafe will delay for the setup time. Touch “SET” icon to activate the value in red and adjust the value with INC and DEC buttons. Touch “SET” icon again to deactivate the value. Touch INC button to move the cursor to “FAIL SAFE ALL” This function allows that all failsafe position for every channel can be set at a time without the use of F.S.POS function. Notice that MODE of all channels should be set to FAIL SAFE.
- RX FREE MIXER • MASTER CH This function is used to correct the unintended movement of airplane during the flight by mixing master channel and slave channel. • MIXER You may decide MIXER number that you want to set. Touch “SET” icon to activate the value in red and select MIXER number with INC and DEC buttons. Touch “SET” icon again to deactivate the value. Touch INC button to move the cursor to “MASTER CH” You may set the master channel of FREE MIXER.
Touch Touch Touch Touch Touch Touch Touch Touch Touch • “S-TRAVEL -, +” It is used to set the mix operation range of SLAVE CH. Touch “SET” icon to activate the value in red and select the slave channel number with INC and DEC buttons. Touch “SET” icon again to deactivate the value. If you operate the master channel, the slave channel is operated within the setup range at the same time.
- RX CURVE It is used to set the curve of CH2, CH3, and CH4 and 3 types of A, B, and C are selectable. • TAIL TYPE You may select the appropriate tale type for the airplane that you use Touch “SET” icon to activate the value in red and select the appropriate tale type with INC and DEC buttons. Touch “SET” icon again to deactivate the value.
Touch “SET” icon again to deactivate the value. If you operate the master channel, the slave channel is operated within the setup range at the same time. Touch INC button to move the cursor to “ALARM VOLT”, Touch Touch Touch Touch Touch Touch Touch Touch Touch - RX SERVO TEST This function allows servo operation to be tested and program the receiver’s power voltage, the alarm for the maximum/minimum temperature of receiver and the channel out type of receiver.
• ALARM VOLT Touch It is the low voltage alarm setup for receiver power battery. Transmitter sounds an alarm throughout telemetry technology when the battery of receiver reaches the low voltage limit. Touch “SET” icon to activate the value in red and adjust the value with INC and DEC buttons. Touch “SET” icon again to deactivate the value.
• ALARM TEMP +/It is the alarm setup for the maximum/minimum temperature of receiver. Transmitter sounds an alarm throughout telemetry technology when the temperature of receiver reaches the temperature limits. Touch “SET” icon to activate the value in red and adjust the value with INC and DEC buttons. Touch “SET” icon again to deactivate the value.
Touch “SET” icon to activate the value in red and select the desired type with INC and DEC buttons. Touch “SET” icon again to deactivate the value. Touch INC button to move the cursor to “CH OUT TYPE” In order to set for CH OUT TYPE, touch “INC” icon to move the cursor to CH OUT TYPE and then touch the “SET” icon. Now, “SAME” in CH OUT TYPE is activated in a red. When it is activated, touch the INC or DEC icons to select the desirable receiver type and then touch the “SET” icon to remove the cursor.
14-5. VOCIE TRIGGER Touch It is used to program the sensors related with voice function. REPEAT, TRIG, VARIO, TRANSSMITTER, RECEIVER are available by default and the optional sensors could be attached. If the optional sensor is connected, it is need to add the optional sensor at SENSOR SELECT mode then new category in VOICE TRIGGER is created. The useable sensors are GENERAL MODULE, ELECTRIC AIR MODULE, VARIO MODULE, GPS, AIR ESC Touch “>>” icon in VOICE TRIGGER line to call “VOICE TRIGGER” setup page.
Touch Touch Touch Touch - TRIG You may designate the switch for the voice functions of transmitter, receiver and sensor. The next voice function is came in turn whenever the switch is on/off To set TRIGGER, touch “NULL” icon to call the “Select” message popup. Move the switch or volume with your choice then that switch or volume is designated as on/ off key and then the key direction setup page appears. You may select ON or OFF by touching icons.
Touch Touch Touch - RECEIVER 수신기의 텔레메트리VOICE기능 TEMP, STRENGTH, RX VOLT, LOW VOLT 4가지 VOICE기능의 사 용을 편집하는 기능입니다. RECIVER기능을 설정하려면 RECIVER기능의 >>를 터치하면 RECIVER 설정화면으로 이동합니다. RECIVER기능으로 이동하면 TEMP, STRENGTH, RX VOLT, LOW VOLT 4가지 RECIVER VOICE기 능이 기본으로 빨간색으로 체크되어 있습니다. 사용하고 싶지 않은 기능을 터치하면 빨간색 체크가 흰색으로 해제되고 RECIVER VOICE기능에서 편집 됩니다. RECIVER기능설정이 끝나면 좌측상단의 BACK를 터치하면 VOICE TRIGGER기능 설정화면으로 이동합니다.
- GENERAL MOD GENERAL MODUL의 텔레메트리 VOICE기능 CELL1, CELL2, CELL3, CELL4, CELL5, CELL6, S1VOLT, S2-VOLT, S1-TEMP, S2-TEMP, RPM, ALT, CURRENT, POWER, CAP 15가지 GENERAL MOD VOICE기능의 사용을 편집하는 기능입니다. GENERAL MOD기능을 설정하려면 GENERAL MOD기능의 >>를 터치하면 GENERAL MOD 설정화 면으로 이동합니다. GENERAL MOD 기능으로 이동하면 CELL1, CELL2, CELL3, CELL4, CELL5, CELL6, S1-VOLT, S2-VOLT, S1-TEMP, S2-TEMP, RPM, ALT, CURRENT, POWER, CAP 15가 지 GENERAL MOD VOICE기능이 기본으로 빨간색으로 체크되어 있습니다. 사용하고 싶지 않은 기 능을 터치하면 빨간색 체크가 흰색으로 해제되고 GENERAL MOD VOICE기능에서 편집 됩니다.
Touch Touch Touch - RECEIVER 수신기의 텔레메트리VOICE기능 TEMP, STRENGTH, RX VOLT, LOW VOLT 4가지 VOICE기능의 사 용을 편집하는 기능입니다. RECIVER기능을 설정하려면 RECIVER기능의 >>를 터치하면 RECIVER 설정화면으로 이동합니다. RECIVER기능으로 이동하면 TEMP, STRENGTH, RX VOLT, LOW VOLT 4가지 RECIVER VOICE기 능이 기본으로 빨간색으로 체크되어 있습니다. 사용하고 싶지 않은 기능을 터치하면 빨간색 체크가 흰색으로 해제되고 RECIVER VOICE기능에서 편집 됩니다. RECIVER기능설정이 끝나면 좌측상단의 BACK를 터치하면 VOICE TRIGGER기능 설정화면으로 이동합니다.
- GENERAL MOD GENERAL MODUL의 텔레메트리 VOICE기능 CELL1, CELL2, CELL3, CELL4, CELL5, CELL6, S1VOLT, S2-VOLT, S1-TEMP, S2-TEMP, RPM, ALT, CURRENT, POWER, CAP 15가지 GENERAL MOD VOICE기능의 사용을 편집하는 기능입니다. GENERAL MOD기능을 설정하려면 GENERAL MOD기능의 >>를 터치하면 GENERAL MOD 설정화 면으로 이동합니다. GENERAL MOD 기능으로 이동하면 CELL1, CELL2, CELL3, CELL4, CELL5, CELL6, S1-VOLT, S2-VOLT, S1-TEMP, S2-TEMP, RPM, ALT, CURRENT, POWER, CAP 15가 지 GENERAL MOD VOICE기능이 기본으로 빨간색으로 체크되어 있습니다. 사용하고 싶지 않은 기 능을 터치하면 빨간색 체크가 흰색으로 해제되고 GENERAL MOD VOICE기능에서 편집 됩니다.
- ESC MOD You may decide the voice functions of ESC MOD to use or not to use. 4 voice functions, RPM, CURRENT, POWER-V, and CAPACITY, are available. Touch “>>” icon to call the ESC MOD setup page. All the functions are marked with red dot by default in the page. Touch the function icon that you don’t want to use then the red dot is switched to white dot. The functions marked with white dot are edited out from the voice functions. Touch “BACK” icon to return to VOICE TRIGGER setup page.
Touch Touch Touch Telemetry Touch Touch Telemetry Touch Touch Touch Touch Touch Touch Touch Touch Touch 73
Touch Touch Touch Touch Telemetry 1-1 NEW This function is used when you wish to create new Q.LINK. If you may want to set for new Q.LINK, touch the value in “Q.LINK” line to activate it in blue and touch “NEW” icon in the right to call “CTRL” and “DELAY” options. In “CTRL” setup, touch “NULL” icon to call “Select” message popup and move the switch or stick with your choice then the switch or stick is set to Q.LINK switch or stick. To set “DELAY” function, touch “0.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch 1-2 NAM Touch It is used when to revise the name of “Q.LINK”. Touch the target value in “Q.LINK” to activate in blue. Now touch “NAM” icon to call NAM setup page. In the page, enter the desired name using the keypad. After that, touch “EN” icon then the revised name is displayed in “New Q.LINK Name”. Now, touch “BACK” icon on the left top left to call “Q.LINK” setup page and the revised name is stored at the corresponding Q.LINK.
1-3 CPY CPY function is used to copy the preset Q.LINK setup data into another Q.LINK. Touch the desired entry in “Q.LINK” line to activate in blue. Touch “CPY” icon to call “COPY” message popup. Touch the entry in TARGET then all entry in TARGET are displayed in turn. Now, select the desired Q.LINK entry and touch “YES” icon then the preset data is saved into the selected Q.LINK entry and return to Q.LINK setup page.
Touch Touch Touch Telemetry Touch Touch Touch After “D/R”, “EXP” setup, perform CTL setup. It is used to assign a switch to D/R, EXP function Touch “NULL” icon in CTL line to call “Select” message popup and move the switch that you want to use then that switch is set on/ off to switch and the switch direction setup page appears. You may select ON or OFF by touching icons. When the switch is moved to the direction of ON, the function is operated. Touch “Back” icon to return D/R, EXP setup page.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch 78 Touch
Touch Touch Telemetry Telemetry 3. Wing MIX A Wing MIX consists of various mixing functions which are essential to fly. There are three types mix, RUDD>>AILE”, “AILE>>RUDD”, and “RUDD>>ELEV” (RATE) B (RATE) B Touch Touch In FUNCTION page, touch “Wing MIX” icon to call “Wing MIX” setup page. Touch “INH” icon in “ACT” line to switch to ON and touch “>>” icon in “SET” line to call “SET” page. In “SET” page, you may adjust the travel amount of slave channel for the master channel operation.
Touch Touch Touch Touch Touch Touch Touch Telemetry 4. THR,CRV Touch Touch 80 This function adjusts the throttle operation curve in relation to the movement of the throttle stick for each condition Since the throttle curve is closely related with Q.LINK setup, Q.LINK setup should precede THR.CRV setup. Call Q.LINK setup page and check Q.LINK setup is completed correctly and touch “BACK” icon to return FUNCTION page. (Refer to the manual on Q.
Touch Touch Telemetry Touch Telemetry Touch Touch Touch Touch In FUNCTIOPN page, touch “THR.CRV” icon to call THR.CRV setup page. You need to mark the point on graph first and then adjust the operation curve with “DEC”, “INC”, X-axis and Y-axis buttons. Touch “ST OFF” to switch to “ST ON” then the throttle position line appears on graph. Move throttle stick and place the line at the desired position between point “L” and “H” then touch “ENT” icon on the bottom right.
Touch Touch Touch Touch Telemetry 5. Idle LOW Touch It is used to lower the idle speed of the engine temporarily when airplane lands In FUNCTIOPN page, touch “Idle LOW” icon to call “Idle LOW” setup page and touch and switch “INH” in ACT line to “ON” then Idle LOW function is activated. Touch “ON” in CTL line to call “Select” message popup then move the switch with your choice then that switch is designated as on/ off switch and then the switch direction setup page appears.
Touch Telemetry 6. Prog.MIX Touch Prog.MIX function is used to mix the different channels for diverse purpose. We recommend you to use the same “On” switch with the one of Q.LINK. You may set the different program mix function for each Q.LINK condition. 8 MIXs are available. The mixing method introduced here is divided into 2 type, liner mixing type and curve mixing type. 1~5 MIXs are liner mixing type and 6~8 MIX is curve mixing type. 6-1. Liner mixing type Touch In FUNCTION page, touch “Prog.
Touch “ENT” icon on the right bottom then the designated position is marked with the red or blue bar in the graph and the value of set position is displayed in POS. If you touch REVERSE in “DIR” line, all setup is reversed. To set “ON” or “OFF” at the both end of stick operation range, touch “SINGLE” icon to switch to “DUAL” then Prog.MIX function is on or off at the both end of stick operation range. Touch “BACK” icon to return to the program mixing setup page.
ACT CTL ACT CTL A B A B Touch Touch Touch 1 1 ACT CTL ACT CTL A B A B Touch Touch Touch Touch 1 1 Touch Touch ACT CTL ACT CTL A B A B Touch Touch 1 1 ACT CTL ACT CTL ACT CTL ACT CTL A B A B A B A B Touch Touch Touch Touch 85
Touch ACT CTL ACT CTL A B A B Touch “PITT >> RUDD” icon in the function page to call PIT >> RUDD setup page. You need to mark the point on graph first and then adjust the operation curve with “DEC”, “INC”, X-axis and Y-axis buttons. Touch “ST OFF” icon to switch to “ST ON” then the pitch position line appears on graph. Move throttle stick and place the line at the desired position between point “L” and “H” then touch “ENT” icon on the bottom right. Now the new point is marked in graph.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch 87
Touch Touch Touch Telemetry Touch Touch Touch Touch Touch Touch Touch Touch 7. Snap roll It is used to select the switch and adjust the value of AILE, ELEV, RUDD channels for the snap roll function. Four snap roll directions can be set for your convenience. In function page, touch “Snap roll” icon to call the snap roll setup page. Touch “INH” icon in ACT line to switch to ON. Touch and activate the value in AILE, ELEV and RUDD line to adjust the values with “INC” and “DEC” buttons.
Touch Touch Touch Telemetry Touch Touch Touch Touch Telemetry Touch 8. Aile diff This function decreases the amount an aileron moves down without affecting the amount the other aileron moves up. This can decrease adverse yaw (right or left movement of the aircraft nose) tendencies during roll maneuvers. Touch “Aile diff” icon to call “Aile diff” setup page. The setup options are different for each wing type.
Touch Touch Touch Touch Telemetry Touch Telemetry Telemetry Touch 9. Flap MIX It consists of 4 mixing types, “FLAP”, ”AILE>>FLAP”, “ELEV>>FLAP”, and “FLAP>>ELEV”. 9-1. FLAP This function is used to adjust the flap angle to increase or decrease airplane lift To setup the flap function, you need to designate on/off control key such as switch, stick and volume. When you move the control key, the flap function is operated. Touch “CH SET” in BASE page to call “CH SET” setup page.
Touch Touch Touch OFFSET Touch OFFSET Touch Touch Touch OFFSET Telemetry Touch OFFSET OFFSET Touch 9-2. AILE >> FLAP OFFSET Touch OFFSET Touch This mixing allows the entire trailing edge of the wing (aileron and flap) to operate as ailerons. When active, as aileron is applied the flaps also move so that the airplane rolls faster. In FLAP MIX page, touch “INH” icon in ACT line to switch to “ON” then AILE >>FLAP function is activated.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch 92 Touch
9-3. ELEV >> FLAP This mixing creates more lift of airplane, allowing a tighter turn. The entire trailing edge of the wing (aileron and flap) operates as flaps when elevator is applied. Touch INH icon in ACT line to switch to “ON” then ELEV >> FLAP is activated. Touch “ON” in CTL line to call the “Select” message popup and move the switch or stick or volume with your choice then that switch or stick or volume is designated as on/ off key and then the key direction setup page appears.
Touch Touch Touch 9-4. FLAP >> ELEV Touch Touch This mixing prevents the change of the nose of airplane that occurs when FLAP is applied by operating elevator In FLAP MIX page, touch “INH” icon in ACT line to switch to “ON” then FLAP >> ELEV function is activated. Touch “ON” in CTL line to call the “Select” message popup and move the switch or stick or volume with your choice then that switch or stick or volume is designated as on/ off key and then the key direction setup page appears.
Touch Touch Touch Touch Touch Touch Flap mix Functions can be adjusted for each Q.LINK condition. 10. Flap sett (Airplane, Gilder) Touch Touch Touch This mixing allows that the aileron, flap and elevator setups are applied at the same time by operating a switch. Touch “Flap sett” icon to access to the “Flap sett” setup page. The first page is AILE setup and you may access to FLAP and ELEV setup page by touching “NEXT” icon in the top right.
Touch Touch Touch Telemetry Touch Touch Touch Touch Touch Touch Touch Touch 96 Touch Touch
Touch touching “NEXT” icon in the top right. Touch “INH” icon in ACT line to switch to “ON” and touch “ON” in CTL line to call the “Select” message popup. Move the switch or stick or volume with your choice then that switch or stick or volume is designated as on/ off key and then the key direction setup page appears. You may select ON or OFF by touching icons. When the key is moved to the direction of ON, the function is operated.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch 98
Touch Touch Touch Telemetry Telemetry 12. Butterfly (Glider) It is used in glider type only. This function allows powerful brake operation by simultaneously raising the left and right ailerons and lowering the flaps. Butterfly produces an extremely efficient landing configuration by flying at a slower speed. CAUTION: We recommend that you do several tests on high altitude to make the best use of this function.
Touch Touch Touch Touch Touch Touch Touch Touch Touch Touch SYSTEM (Helicopter, Airplane, Gilder) 1. ST mode Touch Touch 100 The Stick model can be selected from 1 to 4. “Mode 1” is widely used in ASIA and Mode 2 is widely used in North America and Europe and also mode 3, 4 are available to use. In the initial page, touch “SYSTEM” icon to call SYSTEM setup page and touch “ST mode” icon to call ST mode setup page.
2. Warning Touch Etc.Set The Warnings function programs an alarm to sound to be made if specific switches or stick positions are in an unsafe position when the transmitter is powered on. You can program 5 warnings such as “Throttle Hold”, “Throttle Cut”, “Thro Position”, “Quick Link”, and “Power Off time”. “On” is basically set in only “Thro Position” and “Off” is basically set in the others. Touch “ON/OFF” icons to switch to “OFF/ON”.
Etc.Set Power on Melody ON Power on Melody ON Speaker Volume 03 Speaker Volume 03 Touch Touch 3. Etc. set It is used to select the battery type and set battery warning voltage, Power on melody and Speaker volume. Touch “Etc. set” icon to call Etc. set page and touch and activate the value in blue. After that, choose the desired battery type, warning time, Power on Melody and Speaker volume with INC and DEC icons. If the setup is completed, touch “BACK” icon to return to the System menu page. 4.
4. Display It is used to adjust TFT LCD’s contrast, back light off time, the sensitivity of Touch sense, Logo color and Glaring sun. Touch “Display” icon in the system menu page to access to the display setup page. In this page, touch and activate the value in blue and set the relevant value to each category with the INC and DEC icons. After the setup is completed, touch “BACK” icon to return to the System menu page. NOTICE: In Glaring sun category, we recommend to switch the value to “ON”.
5. Stick Cali It is used to calibrate the stick’s neutral position Touch “Stick Cali” icon in the system menu page to call “Stick Cali’ page. The right stick and the left stick of transmitter are calibrated in turn and the stick position is indicated on VERTI, HORIZ with percentage Touch Touch - Center: When the dot is centered on the graph, move and hold the stick at the desired neutral position and touch “SET” icon then the stick’s neutral position is saved.
6. MP3 You may listen to the music by storing music files on SD card. You can enjoy music while flying or practicing. To make use of MP3 function, touch “MP3” icon to call the MP3 setup page. You may select folder with icons and select the song with “<<, >>” icons. Also you can control a volume with “–“ and ”+” icons. You may repeat the music (all song, one song selectable) and stop the repeat with a repeat icon and play or pause the music with the start and pause icon.
• SAFETY APPROVAL • NOTE This equipment has been tested and found to comply with the limits for a Class B digital deDeclaration of Conformity vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable (in accordance with ISO/IEC 17050-1) protection against harmful interference in a residential installation.
• Caution • This equipment’s aerial must be at least 20 cm from any person when the system is in use. We therefore do not recommend using the equipment at a closer range than 20cm. •E nsure that no other transmitter is closer than 20cm from your equipment, in order to avoid adverse effects on the system’s electrical characteristics and radiation pattern. • The radio control system should not be operated until the Country setting has been set correctly at the transmitter.
No.
