Owner's manual

CAUTION

Verify the chemical compatibility of the pump wetted parts and the substance being pumped, flushed or

recirculated. Chemical compatibility may change with temperature and concentration of the chemical(s)

within the substance being pumped, flushed or recirculated.

The pump should not be used for the structural support of the piping system. Be certain system compo-

nents are properly supported to prevent stress on the pump parts.

Do not allow pump to operate dry for long periods of time; this may cause unnecessary wear or damage

to the pump.

Maximum temperature limits are based upon mechanical stress only. Certain chemicals will significantly

reduce maximum safe operating temperatures. Consult Graymills for chemical compatibility and temper-

ature limits.

SAFETY PRECAUTIONS

United States Government safety standards have been adopted under the Occupational Safety and Health Act. You should

consult these standards—particularly the General Standards, Part 1910, and the Construction Standards, Part 1926.

Technical Data

Maximum fluid working pressure 100 psi (0.7 MPa, 7 bar). . . . . .

Air pressure operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25 to 100 psi (0.18 to 0.7 MPa, 1.8 to 7 bar )

Maximum air consumption 28 scfm (0.672 cubic meters/min.). .

Maximum free flow delivery (1/2 in. ports) 15 gpm (57 l/min). . .

Maximum pump speed 400 cpm. . . . . . . . . . . . . . . . . . . . . . . . . .

Gallons (Liters) per cycle 0.04 (0.15). . . . . . . . . . . . . . . . . . . . . .

Maximum suction lift (water w/buna balls) . . . . . . . . . . . . . . . . . .

15 ft (4.5 m) dry, 25 ft (7.6 m) wet

Maximum size pumpable solids 3/32 in. (2.5 mm). . . . . . . . . . . .

Sound power level (measured per ISO standard 9614–2)

At 70 psig (0.48 MPa, 4.8 bar) at 50 cycles per minute 77 dBa. . .

At 100 psig (0.7 MPa, 7 bar) at maximum cycles per minute 95 dBa

Sound pressure level (measured 1 meter from pump)

At 70 psig (0.48 MPa, 4.8 bar) at 50 cycles per minute 67 dBa. . .

At 100 psig (0.7 MPa, 7 bar) at maximum cycles per minute 85 dBa

Air inlet size 1/4 npt(f). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Air exhaust port size 3/8 npt(f). . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fluid inlet size. 1/2 and 3/4 in. npt(f) or bspt(f). . . . . . . . . . . . . . .

Fluid outlet size. 1/2 and 3/4 in. npt(f) or bspt(f). . . . . . . . . . . . . .

Wetted parts (in addition to ball, seat, duckbill, and diaphragm

materials, which vary by pump)

Polypropylene pumps polypropylene, PTFE. . . . . . . . . . . . . . . . .

Non-wetted external parts polypropylene, stainless steel, polyester

and aluminum (labels), nickel-plated brass

Weight (approximate) 6.5 lb (2.9 kg). . . . . . . . . . . . . . . . . . . . . . .

Hytrel

is a registered trademark of the DuPont Company.

Loctite is a registered trademark of the Loctite Corporation.