Use and Care Manual
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3 Follow all workshop safety rules, regulations, and conditions when using wrench.
p WARNING! Disconnect from air supply before changing accessories or servicing.
3 Maintain the wrench in good condition and replace any damaged or worn parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
p WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
3 Only use impact sockets which are specifically designed for use with an impact wrench.
3 Wear approved safety eye/face shield, ear defenders and hand protection.
p WARNING! Due to the possible presence of asbestos dust from brake linings, when working
around vehicle brake systems we recommend you wear suitable respiratory protection.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Keep children and non essential persons away from the working area.
7 DO NOT use the wrench for a task it is not designed to perform.
p
WARNING! DO NOT use wrench if damaged or thought to be faulty. (Contact Service Agent).
7 DO NOT use wrench unless you have been instructed in its use by a qualified person.
7 DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
7 DO NOT operate wrench if you are tired, under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT carry wrench with your hand on the power trigger in order to avoid unintentional starting.
7 DO NOT direct air from the air hose at yourself or others.
3 When not in use disconnect from air supply and store in a safe, dry, childproof location.
INSTRUCTIONS FOR:
1/2SQ DR G3 AIR
IMPACT WRENCH
MODEL: GSA02
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMA
TION:
For a copy of our latest cat
alogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
2. INTRODUCTION & SPECIFICATION
Drive size . . . . . . . . . . . . . . . . . . . . . . . . . .1/2
Working/Max torque . . . . . . . . . . . .400/460ft.lb
Ultimate torque . . . . . . . . . . . . . . . . . . . 500ft.lb
Air consumption . . . . . . . . . . . . . . . . . . .5.6cfm
Operating pressure . . . . . . . . . . . . . . . . .90psi
Air inlet size . . . . . . . . . . . . . . . . . . . . .1/4BSP
W
eight
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1kg
Noise . . . . . . . . . . . . . . . . . . . . . . . . . . .94.2dB
Vibration . . . . . . . . . . . . . . . . . . . . . . . .4.4m/s
2
Third Generation twin hammer impact wrench.
Suitable for garage, tyre shop and workshop
applications. Handle exhaust reduces noise output
and contoured soft-grip handle gives added
comfort and control. Features three-position
adjustable air/torque control and reversible action.
Issue No: 1
Date Issued: 151104
Item Part No Description
21 GSA02.21 FRONT END PLATE
22 GSA01.22 ROTOR
23 GSA01.23 ROTOR BLADE
24
GSA01.24 FRONT DOWEL PIN
25 GSA01.25 CYLINDER
26 GSA01.26 REAR DOWEL PIN
27 GSA02.27 REAR END PLATE
28 GSA02.28 FRONT BEARING
29 GSA01.29 REAR COVER GASKET
30 GSA01.30 REAR COVER
31 GSA01.31 OIL SEAL
32 GSA01.42 TRIGGER SHAFT
33 GSA02.33 HAMMER PIN
34 GSA02.34 HAMMER
35 GSA02.35 HAMMER CAGE
36 GSA02.36 STANDARD ANVIL
37 GSA01.37 O-RING
38 GSA01.38 ANVIL COLLAR
39 GSA02.39 ANVIL BUSHING
40 GSA01.41 REAR COVER COLLAR
41 GSA02.41 O-RING
Item Part No Description
1 GSA02.01 HOUSING
2 GSA01.02 O-RING
3 GSA01.03 CAP SCREW
4 GSA02.04 HAMMER CASE
5 GSA01.05 SPRING PIN
6 GSA01.06 TRIGGER
7 GSA01.08 VALVE SEAT
8 GSA01.09 THROTTLE VALVE
9 GSA01.10 VALVE SPRING
10 GSA01.11 EXHAUST DEFLECTOR
11 GSA02.11 TRIGGER BUSHING
12 GSA01.12 AIR INLET
13 GSA02.13 PLASTIC GRIP
14 GSA01.14 VALVE BUSHING
15 GSA01.15 WASHER
16 GSA01.16 SWITCH
17 GSA01.17 PIN
18 GSA01.18 REVERSE KNOB
19 GSA20.07 SPRING
20 GSA20.08 LOCK PIN
Parts List For:
GSA02
01284 757500
01284 703534
E-mail:
sales@sealey.co.uk
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
W
eb address: www.sealey.co.uk
GSA02 - 1 - 151104
GSA02 - 1 - 151
104