Installation, Operation, Maintenance and Parts 7 Foot and 10 Foot End-Wheel No-Till Drills Small Seeds Attachments Manufacturing, Inc. www.greatplainsmfg.com ! Read the installation manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! 10927 Cover illustration shows only selected components for a portion of one kit.
7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Table of Contents Important Safety Information.................................... 1 Introduction ................................................................ 3 Description of Unit........................................................ 3 Compatible Drills.......................................................... 3 Available Kits ............................................................... 3 Using This Manual ...........................
1 Great Plains Manufacturing, Inc. Important Safety Information Look for Safety Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it.
2 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Practice Safe Maintenance ▲ Understand procedure before doing work. Use proper tools and equipment. Refer to this manual for additional information. OFF ▲ Work in a clean, dry area. ▲ Make sure all moving parts have stopped and all system pressure is relieved. ▲ Inspect all parts. Make sure parts are in good condition and installed properly. ▲ Remove buildup of grease, oil or debris.
Introduction Great Plains Manufacturing, Inc. 3 Introduction Description of Unit U These kits add small seeds planting capability to many Great Plains 7-foot and 10-foot end-wheel drills. R These kits also replace an older kit (before July 1991), and may be used to upgrade drills with the previous small seeds components. The kit drive is independent of main seed rate, and unaffected by changes to main seed box Drive Type.
4 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Using This Manual U This manual familiarizes you with safety, assembly, operation, adjustments and maintenance. Follow the recommendations to help ensure safe and efficient operation. B R F D L Definitions The following terms are used throughout this manual. Note: Paragraphs in this format provide useful information related to the current topic.
Installation Instructions Great Plains Manufacturing, Inc. 5 Installation Instructions Before You Start Most accidents are the result of negligence and carelessness, usually caused by failure of the operator to follow simple but necessary safety precautions. Allow no one to install the small seeds attachment before carefully reading this manual. Due to evolving manufacturing practices, some subassemblies may already be completely pre-assembled.
6 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Update Clutch Shaft The existing clutch shaft is updated with a third sprocket for Small Seeds. The clutch shaft is located at the front of the main seed box, below the gearbox or transmission. If you have a late model drill, you may already have a Small Seeds drive sprocket installed. Refer to Figure 4 8. Inspect the existing clutch shaft 1 .
Installation Instructions Great Plains Manufacturing, Inc. 7 Seed Box Mounting Refer to Figure 5 If you have a late model drill, you may already have a Small Seeds-ready main seed box, with mounting holes present, and occupied by fasteners. 16. Inspect the back of the main seed box. If there are fasteners at the hole positions in Figure 5, remove them (they are not re-used), and continue at “Mount Small Seeds Box” on page 8. Mark Holes for Drilling Box 17.
8 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Mount Small Seeds Box Refer to Figure 6 19. Select the box assembly 1 , which is one of: 101 123-502L EWNT SGS BOX ASSY 7’-7 102 123-503L EWNT SGS BOX ASSY 7’-7.5&8 103 123-504L EWNT SGS BOX ASSY 7’-10 110 123-505L EWNT SGS BOX ASSY 10’-7 111 123-506L EWNT SGS BOX ASSY 10’-7.5 112 123-507L EWNT SGS BOX ASSY 10’-8 113 123-508L EWNT SGS BOX ASSY 10’-10 At least two people are needed to mount this. 20.
Installation Instructions Great Plains Manufacturing, Inc. 9 Install Rate Adjuster Refer to Figure 7 and Figure 26 on page 28 25. If the rate adjuster is already assembled and mounted, continue at step 36. The handle pivot is pre-installed. 187 117 131 117 154 174 Mount Adjuster Bracket 26. Select one: 131 123-410D GAUGE MOUNTING BRACKET and two sets: 187 802-004C HHCS 1/4-20X3/4 GR5 159 804-006C WASHER LOCK SPRING 1/4 PLT 152 803-006C NUT HEX 1/4-20 PLT 27.
10 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Install Jackshaft Assembly Refer to Figure 8 37. Select one new: 198 123-509S EWNT SGS JACKSHAFT SUB-ASSY and 4 sets new: 188 802-079C HHCS 3/8-16X1 1/4 GR5 160 804-012C WASHER FLAT 3/8 SAE PLT 194 804-013C WASHER LOCK SPRING 3/8 PLT 192 803-014C NUT HEX 3/8-16 PLT 188 198 1 38. If the drill is equipped with fertilizer, temporarily disconnect the left two hoses. They are reconnected at step 52. 160 39.
Installation Instructions Great Plains Manufacturing, Inc. 11 Jackshaft Input Chain The remaining chain may require modification prior to installation. 45. Select one new: 199 136-100D CHAIN RL #40 107 PITCHES The string count includes the main string 1 , a short string 2 , two connectors 3 and one offset link 4 . Open the chain at one connector 3 clip 5 . 3 3 2 4 1 If the drill has fertilizer or Native Grass capability installed, it uses the full 107 pitches of the chain. Continue at step 47.
12 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc.
Installation Instructions Great Plains Manufacturing, Inc. 13 Fertilizer Drill Hoses Refer to Figure 13 52. If fertilizer delivery hoses 1 were disconnected, reconnected them now. As needed, one or two hoses may be routed through the jackshaft bracket. 1 Figure 13 Re-Route Fertilizer Hose Install Chain Guard Refer to Figure 14 53.
14 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Install Row Delivery Components Start with the meter on the right end of the drill. Hoses at Meters 58. Select one each new: 207 123-307D GRASS SEED HOSE, 60IN. 210 800-029C SINGLE WIRE HOSE CLAMP #14 59. Place a clamp hose 207 . 210 2 about 2in from one end of the 60. Slide this end of the hose fully on to the output port of the right end (or next available) Small Seeds meter 2 . 61.
Installation Instructions Great Plains Manufacturing, Inc. Press Wheel Hose Delivery Hardware Start with the row unit on the right end of the drill. 207 206 15 214 71. Before mounting the first retainer, examine the row unit. Decide whether Small Seeds delivery is to be in-row or between rows. If Seed-Lok is present, that constrains where the retainer can be placed. Refer to Figure 17 72.
16 7ft and 10ft EWNT Small Seeds Walkboard Components Great Plains Manufacturing, Inc. 1 192 194 179 Extend Walkboard Refer to Figure 18 77. Select two new: 181 123-260D STEP EXTENSION MOUNT ANGLE 152 159 187 2 78. Select four sets of new: 179 119-032D 3-PT STEP RETAINER 188 802-079C HHCS 3/8-16X1 1/4 GR5 194 804-013C WASHER LOCK SPRING 3/8 PLT 192 803-014C NUT HEX 3/8-16 PLT 79. Orient the angles 181 so that the ends with the holes furthest apart are to the front.
Operations Great Plains Manufacturing, Inc. 17 Operations Loading Seed Small Seed may be loaded in the field or prior to transport. The drill must be hitched for seed loading. The mainframe may be raised or lowered. Lowered places the walkboards closer to the ground, reducing effort when manually loading bagged seed. Small Seeds Box Loading 1. If loading prior to transport, and calibration has not yet been done, set Seed Rate Handles to 0.
18 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Small Seeds Rate Calibration Differences will exist between the tested seed and field conditions used to generate the Small Seeds Rate Charts, and your seed and conditions. To accurately achieve your target population, Great Plains recommends calibrating. Perform the calibration with the drill lowered to planting position (if the openers are raised, the clutch disengages). Leave the tractor hitched for movement control.
Operations Great Plains Manufacturing, Inc. 10. Divide the net seed weight by three. Multiply by number of openers on your drill to determine the total of pounds-per-acre seeded. 19 NetWeight MeasuredRate = ------------------------ × RowCount 3 For example: a 7.5in drill has 15 rows: 10.5 lbs/ac 2.1 10.5 = ------ × 15 3 11. The Seed Rate Handle scale is a percentage of meter opening, and is quite linear near scale center. Calculate a new scale setting based on the test.
20 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Small Seeds Row Shut-Off Refer to Figure 20 If alternate row spacing is required for small seeds, optional plugs are available to block flow inside the seed box tray. 1. Cleanout seed. The seed box must be empty prior to inserting plugs. See “Small Seeds Box Cleanout” on page 23. 2. Before installing plugs, inspect the seed boxes for existing factory-installed plugs. These are blocking extra unused seed ports.
Seed Rate Great Plains Manufacturing, Inc. 21 Seed Rate Alfalfa, Red Alsike, Crimson Clover Rows 7.0 inch 7.5 inch 8.0 inch 10 inch 0 5 10 15 20 25 30 0 0 0 0 0.0 0.0 0.0 0.0 1.9 1.8 1.6 1.3 3.0 2.8 2.6 2.1 4.1 3.9 3.6 2.8 5.1 4.8 4.5 3.5 6.4 6.0 5.6 4.4 Small Seeds Cup Lever Setting 35 40 45 50 55 60 65 Seeding Rate in Pounds per Acre 7.5 8.4 9.5 10.8 11.8 12.9 14.0 7.0 7.9 9.0 10.0 11.1 12.1 13.2 6.6 7.4 8.4 9.4 10.3 11.3 12.3 5.1 5.8 6.6 7.4 8.1 8.9 9.
22 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Rate Charts, Small Seeds Box, continued... Orchard Grass Rows 7.0 inch 7.5 inch 8.0 inch 10 inch 0 5 10 15 20 25 30 0 0 0 0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.2 0.2 0.2 0.1 0.6 0.5 0.5 0.4 0.7 0.7 0.7 0.5 1.1 1.1 1.0 0.8 Small Seeds Cup Lever Setting 35 40 45 50 55 60 65 Seeding Rate in Pounds per Acre 1.3 1.7 2.1 2.4 2.8 3.0 3.4 1.2 1.6 1.9 2.3 2.6 2.8 3.2 1.1 1.5 1.8 2.1 2.5 2.6 2.9 0.9 1.2 1.4 1.7 1.9 2.1 2.
Maintenance Great Plains Manufacturing, Inc. 23 Maintenance Small Seeds Box Cleanout 1. Open lid of each box and scoop out as much seed as possible. 2. To recover remaining seed, place a collection tarp under the small seeds tubes at the openers. 3. Raise drill. 4. Set seed rate handles to 100. 5. Rotate gauge wheels until no seed flows. 6. If a vacuum cleaner is available, remove any residual seed from top of meters. Chain Maintenance Inspect and lubricate chains regularly.
24 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc.
Options Great Plains Manufacturing, Inc. 25 Options Small Seed Tube Plugs This plug stops seed flow from the small seeds box above the meter. Order one per row to set inactive. Description Part Number SML SDS CUP PLUG 133-315H Figure 23 Small Seeds Tube Plug 27407 Figure 24 Small Seeds Removable Partition 17028 Small Seed Removable Partition This partition reduces side-to-side seed flow in the small seeds box.
26 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Appendix New Parts Overall Kit 190 183 191 192 180 193 182 179 109 152 194 159 187 189 160 194 201 101 197 199 203 204 192 196 181 102 195 103 193 193 188 191 185 195 193 189 193 110 191 112 210 188 186 111 207 113 See page 29.
Appendix Great Plains Manufacturing, Inc. 27 7-Foot Kits Kits: 123-499A EWNT SML SDS PW MNT 7’-7 123-500A EWNT SML SDS PW MNT 7’-7.
28 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc.
Appendix Great Plains Manufacturing, Inc. 29 Box Subassemblies Kits: 101 123-502L EWNT SGS BOX ASSY 7’-7 111 123-506L EWNT SGS BOX ASSY 10’-7.5 102 123-503L EWNT SGS BOX ASSY 7’-7.
30 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc.
Appendix Great Plains Manufacturing, Inc.
32 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Row Unit Components 210 206 207 214 207 213 210 214 211 159 152 1 212 205 210 207 208 209 214 159 211 152 214 206 205 209 NOTE: MUST BE MOUNTED TO FRONT WHEN USED WITH SEED-LOK.
Appendix Great Plains Manufacturing, Inc.
34 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc.
Appendix Great Plains Manufacturing, Inc.
36 7ft and 10ft EWNT Small Seeds Great Plains Manufacturing, Inc. Torque Values Bolt Head Identification Bolt Head Identification Bolt Size Bolt Size Grade 2 1 Grade 5 3 Grade 8 4 8.8 10.9 Class 5.8 Class 8.8 Class 10.9 N-m ft-lb N-m ft-lb mm x pitch N-m ft-lb N-m ft-lb N-m 1 7.4 5.6 11 8 16 12 M 5 X 0.8 4 3 6 5 9 7 1⁄ 4-28 8.5 6 13 10 18 14 M6X1 7 5 11 8 15 11 5 ⁄16-18 15 11 24 17 33 25 M 8 X 1.
Appendix Great Plains Manufacturing, Inc.
38 7ft and 10ft EWNT Small Seeds 123-535M Great Plains Manufacturing, Inc.
39 Great Plains Manufacturing, Inc.
40 7ft and 10ft EWNT Small Seeds 123-116D 123-118D 123-202D 123-259D 123-260D 123-298D 123-304D 123-307D 123-352D 123-356D 123-358D 123-359D 123-361D 123-362D 123-363D 123-365D 123-372H 123-373H 123-376H 123-377H 123-378H 123-409D 123-410D 123-424D 123-429D 123-430D 123-431D 123-432D 123-464H 123-476H 123-489H 123-490H 123-491H 123-492H 123-494H 123-495A 123-496A 123-497A 123-498A 123-499A 123-500A 123-501A 123-502L 123-503L 123-504L 123-505L 123-506L 123-507L 123-508L 123-509S 123-510K 123-535M 29 29 1
Great Plains Manufacturing, Inc. Corporate Office: P.O.