Assembly Instructions Owner manual

ManualsBrandsGreat Plains ManualsGardening equipment1006

Great Plains Mfg., Inc.

Used with:

Installation Instructions

151-118M

706/1006 No-Till Drill

Option Installation

• 706 End Wheel No-Till Drill

• 1006 End Wheel No-Till Drill

General Information

When you see this symbol, the subsequent instructions and

warnings are serious - follow without exception. Your life and

the lives of others depend on it!

These instructions explain how to install the Small Grass

Seeds, Fertilizer and Native Grass Seeds options.

These instructions apply to:

133-251A 706-7 Seed to SGS in row

133-252A 706-7 Seed to SGS side del.

133-253A 706-7 1/2 & 8 Seed to SGS in row

133-254A 706-7 1/2 & 8 Seed to SGS side del.

133-255A 1006-7 Seed to SGS in row

133-256A 1006-7 Seed to SGS side del.

133-257A 1006-7 1/2 Seed to SGS in row

133-258A 1006-7 1/2 Seed to SGS side del.

133-259A 1006-8 Seed to SGS in row

133-260A 1006-8 Seed ti SGS side del.

133-261A 706-7 NG to SGS in row

133-262A 706-7 NG to SGS side del.

133-263A 706-7 1/2&8NGtoSGSinrow

133-264A 706-7 1/2&8NGtoSGSside del.

133-265A 1006-7 NG to SGS in row

133-266A 1006-7 NG to SGS side del.

133-267A 1006-7 1/2 NG to SGS in row

133-268A 1006-7 1/2 NG to SGS side del.

133-269A 1006-8 NG to SGS in row

133-270A 1006-8 NG to SGS side del.

133-271A 706-7 Fert. to SGS in row

133-272A 706-7 Fert. to SGS side del.

133-273A 706-7 1/2&8Fert.toSGSinrow

133-274A 706-7 1/2&8Fert.toSGSside del.

133-275A 1006-7 Fert. to SGS in row

133-276A 1006-7 Fert. to SGS side del.

133-277A 1006-7 1/2 Fert. to SGS in row

133-278A 1006-7 1/2 Fert. to SGS side del.

133-279A 1006-8 Fert. to SGS in row

133-280A 1006-8 Fert. to SGS side del.

142-920A 706-7 Seed to Fert.

142-921A 706-7 1/2 & 8 Seed to Fert.

142-922A 1006-7 Seed to Fert.

142-923A 1006-7 1/2 Seed to Fert.

142-924A 1006-8 Seed to Fert.

142-925A 706-7 Seed & SGS to Fert.

142-926A 706-7 1/2 & 8 Seed & SGS to Fert.

142-927A 1006-7 Seed & SGS to Fert.

142-928A 1006-7 1/2 Seed & SGS to Fert.

142-929A 1006-8 Seed & SGS to Fert.

8/2/2005

142-930A 706-7 Seed to Fert. & SGS

142-931A 706-7 1/2 & 8 Seed to Fert. & SGS

142-932A 1006-7 Seed to Fert. & SGS

142-933A 1006-7 1/2 Seed to Fert. & SGS

142-934A 1006-8 Seed to Fert. & SGS

202-546A 706-7 Seed to NG

202-547A 706-7 1/2 & 8 Seed to NG

202-548A 1006-7 Seed to NG

202-549A 1006-7 1/2 Seed to NG

202-550A 1006-8 Seed to NG

202-563A 706-7 Seed & SGS to NG

202-564A 706-7 1/2 & 8 Seed & SGS to NG

202-565A 1006-7 Seed & SGS to NG

202-566A 1006-7 1/2 Seed & SGS to NG

202-567A 1006-8 Seed & SGS to NG

202-569A 706-7 Seed to NG & SGS

202-570A 706-7 1/2 & 8 Seed to NG & SGS

202-571A 1006-7 Seed to NG & SGS

202-572A 1006-7 1/2 Seed to NG & SGS

202-573A 1006-8 Seed to NG & SGS

Manual Update

Refer to the 706/1006 No-Till Drill operator’s manual for de-

tailed information on safely operating, adjusting,

troubleshooting and maintaining the various options men-

tioned in this installation manual. Refer to the parts manual

for part identiﬁcation. Refer to the seed rate book for setup,

calibration and seed rates.

150-285M Operator’s Manual

150-285P Parts Manual

150-285B Seed Rate Book

Before You Start

Pages 23 through 40 are a detailed listing of parts included

in the various option packages. Use these lists to inventory

parts received. Detailed illustrations of sprock conﬁgura-

tions for the various option packages are located on pages

17 through 22.

Tools Required

• Basic hand tools

Deﬁnitions

Right-hand and left-hand as used in this manual are deter-

mined by facing the direction the machine will travel while in

use unless otherwise stated.

Summary of content (40 pages)

PAGE 1
Great Plains Mfg., Inc. Installation Instructions 706/1006 No-Till Drill Option Installation Used with: • 706 End Wheel No-Till Drill • 1006 End Wheel No-Till Drill ! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! General Information These instructions explain how to install the Small Grass Seeds, Fertilizer and Native Grass Seeds options.
PAGE 2
Great Plains Mfg., Inc. 2 Option Installation Assembly Instructions Small Grass Seed 1. Lower drill to the ground. 2. Remove walkboard, walkboard mounts and walkboard supports. Save hardware. 6. Mount the small grass seed box (2) to the mounting brackets (1) using 3/8" x 1" bolts, 3/8" lock washers and 3/8" nuts. 3. Remove and save all box handles and hardware. 4. Assemble new walkboard end panels and harrow supports.
PAGE 3
Great Plains Mfg., Inc. Installation Instructions 3 Refer to Figure 2 7. Assemble and route the chain (1) from the sprocket (2) on the drive bracket to the sprocket on the small grass seed box (3). Adjust idler (4) to remove chain slack. NOTE: With fertilizer and/or seed box agitator options already installed, a large portion of the drive is already completed. With Fertilizer Refer to Figure 2 8. Add 17 tooth sprocket (5) to the fertilizer box shaft.
PAGE 4
Great Plains Mfg., Inc. 4 Option Installation Without Fertilizer or Seed Box Agitator and Drills with Native Grass Seed Refer to Figure 5 12. Working at the front left side of the drill, remove the second and third front 1/2" x 1 1/4" long bolts (1) that join the box to the frame. Install the idler (2) 1/2" x 3" long bolt, 1/2" flat washer, 1/2" jam nut and 1/2" flange lock nut to bracket (3) as shown. 13. Install bracket (3) and (4) as shown. Leave loose until final assembly.
PAGE 5
Great Plains Mfg., Inc. Installation Instructions 5 Seed Tube Assembly The openers on the 706/1006 have two locations for small grass delivery. In row or side delivery. The in row delivery is installed in the rear opener hole while the side delivery attaches to the side of the opener. Refer to Figure 6 19. Insert the seed tube (1) into the hole on the top of the opener. Secure in place with a number 10-16 x 1/2” screw (2). 20. Slide a hose clamp (4) over the hose (3).
PAGE 6
Great Plains Mfg., Inc. 6 Option Installation Fertilizer Box 1. Lower drill to the ground. 2. Remove walkboard, walkboard mounts and walkboard supports. Save hardware. 3. Remove and save all box handles and hardware. 4. Assemble new walkboard end panels and harrow supports. Re-attach existing ladder to left-hand walkboard end using hardware removed in step 2. 6. Mount the fertilizer box (2) to the seed box using 1/2" x 1 1/4" bolts and 1/2" flange nuts on the outside ends.
PAGE 7
Great Plains Mfg., Inc. Installation Instructions 7 With Seed Box Agitator Refer to Figure 8 8. Install the 17 tooth sprocket (1) on the end of the fertilizer jackshaft. Align it with the fertilizer drive sprocket on the end to the shaft. Route the 103 pitch chain (2) and remove slack with the idler sprocket. 22615 Figure 8 Sprocket and Chain Refer to Figure 9 9. Replace the agitator drive chain with the longer one provided. Route chain as shown and adjust idlers to remove chain slack.
PAGE 8
Great Plains Mfg., Inc. 8 Option Installation Without Seed Box Agitator Refer to Figure 10 bearings. Place the 22 tooth sprocket (11) on the inboard side of the shaft and the 12 tooth sprocket (13) on the out board side of the shaft. 10. Working at the front left side of the drill, remove the second and third front 1/2" x 1 1/4" long bolts (1) that join the box to the frame.
PAGE 9
Great Plains Mfg., Inc. Installation Instructions 9 Seed Tube Assembly Refer to Figure 11 17. Attach the fertilizer hoses (1) to the drop tubes on the fertilizer box with ratchet clamps (2). 18. Route the hoses behind the rear frame tubes on the drill. Attach the opener adapter (3) to the large hole in the opener and secure in place with 10 x 3/8" machine screws. 19. Insert the fertilizer tube (4) into the opener adapter (3) with the tube opening facing forward.
PAGE 10
Great Plains Mfg., Inc. 10 Option Installation Native Grass 1. Lower drill to the ground. 2. Remove walkboard, walkboard mounts and walkboard supports. Save hardware. 3. Remove and save all box handles and hardware. 4. Assemble new walkboard end panels and harrow supports. Re-attach existing ladder to left-hand walkboard end using hardware removed in step 2. Refer to Figure 12 flange nuts on the outside ends. Use existing bolts and nuts from the seed box partitions to attach the box mount brackets (1).
PAGE 11
Great Plains Mfg., Inc. Installation Instructions 11 Refer to Figure 13 9. Access drive gauge wheel hub by removing end cap (1). Be careful and leave the hub seal (2) in place. Remove plastic cap (3) on the inside end of the gauge wheel spindle. Insert spindle bearing (4) into the area where the plastic cap (3) was removed. Make sure the set screws are accessible. 10. Insert right-hand lockout drive shaft (5) through drive spindle, through bearing (4) and through 19 tooth sprocket (6).
PAGE 12
Great Plains Mfg., Inc. 12 Option Installation Refer to Figure 15 17. Align the two 19 tooth sprockets (6) with each other and tighten the set screws to hold them in place. 18. Feed the 188 pitch chain (13) through the gauge wheel tube and around the sprockets and idler assembly. 19. Adjust the square head idler adjustment screw to give tension to the chain. Place the access cover (14) over the hole and secure it and the adjustment screw in place with the jam nut. 20.
PAGE 13
Great Plains Mfg., Inc. Installation Instructions 13 Refer to Figure 17 25. Mount the gearbox (1) to the frame using 3/8" x 1" self tapping screws. Make sure it is square with the frame. 26. Slide the 19 tooth spline bore sprocket (2) on the rear inboard shaft and secure it in place with an external snap ring. 27. Slide the 25 tooth clutch sprocket (3) on the outboard shaft and secure it in place with an external snap ring. 28.
PAGE 14
Great Plains Mfg., Inc. 14 Option Installation 34. Align sprocket (4) with the sprocket on the gearbox. Slide both of the locking collars (3) against the bearings (1) and tighten set screws. Make sure sprocket (4) is still aligned with the sprocket on the gearbox. 35. Add two idlers (5) to the frame plate using using 1/2" x 3" bolt, 1/2" jam nut, 1/2" flat washers and 1/2" flange lock nut on each one. 36. Route 108 pitch chain (8) around the gearbox sprocket and sprocket (4) and tighten with idlers (5).
PAGE 15
Great Plains Mfg., Inc. Installation Instructions 15 Native Grass Seed Tube Installation Refer to Figure 21 46. Insert the native grass seed tube (1) in the hole behind the springs and secure in place with two 10-16 x 3/8" screws and 1/4" flat washers. 47. Attach one end of the seed hose (2) to the seed tube (1) with a #42 hose clamp the other end to the native seed cup with a #42 hose clamp. Walkboard Assembly 48.
PAGE 16
Great Plains Mfg., Inc. 16 Option Installation Adding Native Grass or Fertilizer to Drills with Seed & SGS 1. Lower drill to the ground. 2. Remove walkboard, walkboard mounts and walkboard supports. Save hardware. 3. Disassemble small grass drive chain from front of drill. Remove SGS box and mount brackets from rear of seed box and frame end panels. Keep all hardware for reuse. 4. Assemble new walkboard end panels and harrow supports.
PAGE 17
Great Plains Mfg., Inc.
PAGE 18
Great Plains Mfg., Inc.
PAGE 19
Great Plains Mfg., Inc.
PAGE 20
Great Plains Mfg., Inc.
PAGE 21
Great Plains Mfg., Inc.
PAGE 22
Great Plains Mfg., Inc.
PAGE 23
Great Plains Mfg., Inc. Installation Instructions 23 133-251A 706-7 Seed to SGS in row delivery Your kit includes: Qty. 1 1 1 11 1 Part No. 119-306L 133-227L 133-243L 133-249L 151-118M Part Description 706 SEED & SGS WALKBOARD A 706-7" SGS BOX ASSY 706 SGS DRIVE BUNDLE SGS OPENER IN-ROW BUNDLE MANUAL 706/1006 OPTION INS 133-252A 706-7 Seed to SGS side delivery Your kit includes: Qty. 1 1 1 11 1 Part No.
PAGE 24
Great Plains Mfg., Inc. 24 Option Installation 133-255A 1006-7 Seed to SGS in row delivery Your kit includes: Qty. 1 1 1 16 1 Part No. 119-307L 133-229L 133-246L 133-249L 151-118M Part Description 1006 SEED & SGS WALKBOARD 1006-7" SGS BOX ASSY 1006 SGS DRIVE BUNDLE SGS OPENER IN-ROW BUNDLE MANUAL 706/1006 OPTION INS 133-256A 1006-7 Seed to SGS side delivery Your kit includes: Qty. 1 1 1 16 1 Part No.
PAGE 25
Great Plains Mfg., Inc. Installation Instructions 25 133-259A 1006-8 Seed to SGS in row delivery Your kit includes: Qty. 1 1 1 14 1 Part No. 119-307L 133-231L 133-246L 133-249L 151-118M Part Description 1006 SEED & SGS WALKBOARD 1006-8" SGS BOX ASSY 1006 SGS DRIVE BUNDLE SGS OPENER IN-ROW BUNDLE MANUAL 706/1006 OPTION INS 133-260A 1006-8 Seed to SGS side delivery Your kit includes: Qty. 1 1 1 14 1 Part No.
PAGE 26
Great Plains Mfg., Inc. 26 Option Installation 133-263A 706-7 1/2 & 8 NG to SGS in row delivery Your kit includes: Qty. 1 1 10 1 1 2 1 Part No. 133-228L 133-245L 133-249L 151-101H 151-102H 151-103H 151-118M Part Description 706-7 1/2-8" SGS BOX ASSY 706 NG/SGS DRIVE BUNDLE SGS OPENER IN-ROW BUNDLE LH NG & SGS WALKBOARD MOUN RH NG & SGS WALKBOARD MOUN NG & SGS HARROW MOUNT MANUAL 706/1006 OPTION INS 133-264A 706-7 1/2 & 8 NG to SGS side delivery Your kit includes: Qty. 1 1 10 1 1 2 1 Part No.
PAGE 27
Great Plains Mfg., Inc. Installation Instructions 27 133-267A 1006-7 1/2 NG to SGS in row delivery Your kit includes: Qty. 1 1 15 1 1 2 1 Part No. 133-230L 133-248L 133-249L 151-101H 151-102H 151-103H 151-118M Part Description 1006-7 1/2" SGS BOX ASSY 1006 NG/SGS DRIVE BUNDLE SGS OPENER IN-ROW BUNDLE LH NG & SGS WALKBOARD MOUN RH NG & SGS WALKBOARD MOUN NG & SGS HARROW MOUNT MANUAL 706/1006 OPTION INS 133-268A 1006-7 1/2 NG to SGS side delivery Your kit includes: Qty. 1 1 15 1 1 2 1 Part No.
PAGE 28
Great Plains Mfg., Inc. 28 Option Installation 133-271A 706-7 Fert. to SGS in row delivery Your kit includes: Qty. 1 1 11 1 1 2 1 Part No. 133-227L 133-244L 133-249L 151-104H 151-105H 151-106H 151-118M Part Description 706-7" SGS BOX ASSY 706 FERT/SGS DRIVE BUNDLE SGS OPENER IN-ROW BUNDLE LH FERT & SGS WALKBOARD MO RH FERT & SGS WALKBOARD MO FERT & SGS HARROW MOUNT MANUAL 706/1006 OPTION INS 133-272A 706-7 Fert. to SGS side delivery Your kit includes: Qty. 1 1 11 1 1 2 1 Part No.
PAGE 29
Great Plains Mfg., Inc. Installation Instructions 29 133-275A 1006-7 Fert. to SGS in row delivery Your kit includes: Qty. 1 1 16 1 1 2 1 Part No. 133-229L 133-247L 133-249L 151-104H 151-105H 151-106H 151-118M Part Description 1006-7" SGS BOX ASSY 1006 FERT/SGS DRIVE BUNDLE SGS OPENER IN-ROW BUNDLE LH FERT & SGS WALKBOARD MO RH FERT & SGS WALKBOARD MO FERT & SGS HARROW MOUNT MANUAL 706/1006 OPTION INS 133-276A 1006-7 Fert. to SGS side delivery Your kit includes: Qty. 1 1 16 1 1 2 1 Part No.
PAGE 30
Great Plains Mfg., Inc. 30 Option Installation 133-279A 1006-8 Fert. to SGS in row delivery Your kit includes: Qty. Part No. 1 1 14 1 1 2 1 133-231L 133-247L 133-249L 151-104H 151-105H 151-106H 151-118M Part Description 1006-8" SGS BOX ASSY 1006 FERT/SGS DRIVE BUNDLE SGS OPENER IN-ROW BUNDLE LH FERT & SGS WALKBOARD MO RH FERT & SGS WALKBOARD MO FERT & SGS HARROW MOUNT MANUAL 706/1006 OPTION INS 133-280A Fert. to SGS side delivery Your kit includes: Qty. 1 1 14 1 1 2 1 Part No.
PAGE 31
Great Plains Mfg., Inc. Installation Instructions 31 142-922A 1006-7 Seed to Fert. Your kit includes: Qty. 1 1 2 16 1 1 1 1 1 1 Part No. 119-296D 142-706H 142-707H 142-909L 142-912L 142-916L 142-918L 142-919L 151-099H 151-118M Part Description 1006 WALKBOARD FERTILIZER WALKBOARD END R FERTILIZER HARROW SUPPORT FERTILIZER OPENER BUNDLE 1006-7" TRAY ASSEMBLY 1006 FERTILIZER BOX ASSEMB 1006 FERTILIZER DRIVE ASSE FERTILIZER MOUNTING HARDWA LH FERT.
PAGE 32
Great Plains Mfg., Inc. 32 Option Installation 142-925A 706-7 Seed & SGS to Fert. Your kit includes: Qty. 1 1 11 1 1 1 1 1 1 2 1 1 1 1 Part No.
PAGE 33
Great Plains Mfg., Inc. Installation Instructions 33 142-928A 1006-7 1/2 Seed & SGS to Fert. Your kit includes: Qty. 1 1 15 1 1 1 1 1 1 2 1 1 1 1 Part No.
PAGE 34
Great Plains Mfg., Inc. 34 Option Installation 142-931A 706-7 1/2 & 8 Seed to Fert. & SGS Your kit includes: Qty. 1 1 1 10 10 1 1 1 1 1 Part No.
PAGE 35
Great Plains Mfg., Inc. Installation Instructions 35 142-934A 1006-8 Seed to Fert. & SGS Your kit includes: Qty. 1 1 1 14 14 1 1 1 1 1 Part No.
PAGE 36
Great Plains Mfg., Inc. 36 Option Installation 202-548A 1006-7 Seed to NG Your kit includes: Qty. 1 1 2 1 1 1 1 1 16 1 1 Part No.
PAGE 37
Great Plains Mfg., Inc. Installation Instructions 37 202-563A 706-7 Seed & SGS to NG Your kit includes: Qty. 1 1 1 2 1 1 1 11 1 1 1 Part No.
PAGE 38
Great Plains Mfg., Inc. 38 Option Installation 202-566A 1006-7 1/2 Seed & SGS to NG Your kit includes: Qty. 1 1 1 2 1 1 1 15 1 1 1 Part No.
PAGE 39
Great Plains Mfg., Inc. Installation Instructions 39 202-570A 706-7 1/2 & 8 Seed to NG & SGS Your kit includes: Qty. 1 1 1 10 1 1 10 1 1 1 1 Part No.
PAGE 40
Great Plains Mfg., Inc. 40 Option Installation 202-573A 1006-8 Seed to NG & SGS Your kit includes: Qty. 1 1 1 14 1 1 14 1 1 1 1 151-118M Part No.