Assembly Instructions Instruction Manual

ManualsBrandsGreat Plains ManualsGardening equipment1300 Fertilizer

Great Plains Mfg., Inc.

Used with:

Installation Instructions

175-196M

1300 13’ End Wheel Drill

1300 Fertilizer Assembly Upgrade

• 1300 13’ End Wheel Drill

General Information

These instructions explain how to install the 1300 Fer-

tilizer Assembly Upgrade. The Fertilizer Assembly

Upgrade allows conversion of a standard seed box to

fertilizer. These instructions apply to:

175-209A 1300 Fertilizer Upgrade 6

175-210A 1300 Fertilizer Upgrade 7 1/2

175-211A 1300 Fertilizer Upgrade 10

10/24/2005

Before You Start

Page 10 is a detailed listing of parts included in

the 1300 Fertilizer Assembly Upgrade. Use this

list to inventory parts received.

Tools Required

• Basic Hand Tools

Install Fertilizer

Refer to Figure 1

1. Replace gas spring (1) on all parti-

tions. Remove ball stud (2) and lock

nut (3) securing spring (1) to box lid

and spring (1) to partition. Discard

all pieces.

2. Attach new gas spring (1) provided

in kit to box lid using new ball stud (2)

and 5/16-18 lock nut (3). Complete

installation by securing spring (1) to

partition using new ball stud (2) and

5/16-18 lock nut (3).

3. Repeat steps 4 and 5 on remaining

partitions.

Refer to Figure 2

4. Install a set of inner (6) and outer (3)

divider clips on both sides of each

box partition (1). Use 5/16-18 x 1 1/4

bolts (5) and 5/16-18 hex nuts (2) to

secure clips (6 and 3) to partitions

(1). Leave bolts loose.

5. Attach a divider angle bracket (4) to

each side of each partition (1) using

5/16-18 x 1 1/4 bolts (5) and 5/16-18

hex nuts (2).

Figure 2

Box Partition

23407

Assembly Instructions

23411

Figure 1

Gas Springs

When you see this symbol, the subsequent instructions and

warnings are serious - follow without exception. Your life and

the lives of others depend on it!

Summary of content (11 pages)

PAGE 1
Great Plains Mfg., Inc. Installation Instructions 1300 13’ End Wheel Drill 1300 Fertilizer Assembly Upgrade Used with: • 1300 13’ End Wheel Drill ! General Information These instructions explain how to install the 1300 Fertilizer Assembly Upgrade. The Fertilizer Assembly Upgrade allows conversion of a standard seed box to fertilizer.
PAGE 2
Great Plains Mfg., Inc. 2 1300 Fertilizer Assembly Upgrade Refer to Figure 3 23408 6. Secure two end mounted divider clips (2) to each end of the box (4) using 5/16-18 x 3/4 bolts (3) and 5/16-18 hex nuts (1). Leave bolts loose. Refer to Figure 4 7. Attach knobs (3) and retaining clips (7) to bottom divider brackets (8, 9, and 2) using 1/4-20 x 1 bolts (5) and 1/4-20 hex lock nuts (6). 8. Place left-hand bottom divider bracket (8) in box on left-hand side of drill.
PAGE 3
Great Plains Mfg., Inc. Installation Instructions 3 11. Slide divider inserts into divider clips in between partitions. 12. Remove top two bolts from each partition divider clip. Refer to Figure 5 13. Attach spill flap to box by securing one top bar partition brace to each box partition divider clip. Use bolts removed in step 12 to secure brace to partition divider clip. NOTE: To complete installation of fertilizer upgrade, there will need to be two people working on the box.
PAGE 4
Great Plains Mfg., Inc. 4 1300 Fertilizer Assembly Upgrade Install Fertilizer Drive Assembly Refer to Figure 7 1. Remove jackshaft (1) from left-hand side of drill. NOTE: It may be necessary to remove other componets so that jackshaft (1) may be removed. For proper reassembly, keep all pieces for reuse and note locations of all other pieces used. 2. Slide sprocket (2) and chain (90 pitches) (5) onto jackshaft (1). Replace jackshaft (1) and reassemble componets. 3.
PAGE 5
Great Plains Mfg., Inc. Installation Instructions 5 Install Fertilizer Hose Refer to Figure 8 1. Secure plastic fertilizer hose (1) and small seeds reinforcement ring (6) to rear of opener using two hex screws (2). 2. Attach seed hose (4) using 1 1/2 hose clamp (3) to plastic fertilizer hose (1). Secure other end of seed hose (4) to fertilizer tray using 1 5/8 hose clamp (5). 3. Complete steps 1 and 2 on all openers.
PAGE 6
Great Plains Mfg., Inc. 1300 Fertilizer Assembly Upgrade 6 175-209A 1300 13’ Fertilizer Upgrade 6 Your kit includes: Qty. Part No.
PAGE 7
Great Plains Mfg., Inc. Installation Instructions 7 175-213L 1300 Fert Drop Tube Box 6 Your kit includes: Qty. Part No. 26 26 52 1 26 10/24/2005 133-065D 800-008C 801-002C 813-033C 817-346C Part Description SML SDS TB REINFORCEMENT CLAMP HOSE 1 1/2 NO. 24 SCREW HEX SLT 10-16 X 1/2P.
PAGE 8
Great Plains Mfg., Inc. 1300 Fertilizer Assembly Upgrade 8 175-210A 1300 13’ Fertilizer Upgrade 7 1/2 Your kit includes: Qty. Part No.
PAGE 9
Great Plains Mfg., Inc. Installation Instructions 9 175-214L 1300 Fert Drop Tube Box 7 1/2 Your kit includes: Qty. Part No. 21 21 42 1 21 10/24/2005 133-065D 800-008C 801-002C 813-033C 817-346C Part Description SML SDS TB REINFORCEMENT CLAMP HOSE 1 1/2 NO. 24 SCREW HEX SLT 10-16 X 1/2P.
PAGE 10
Great Plains Mfg., Inc. 10 1300 Fertilizer Assembly Upgrade 175-211A 1300 13’ Fertilizer Upgrade 10 Your kit includes: Qty. Part No.
PAGE 11
Great Plains Mfg., Inc. Installation Instructions 11 175-215L 1300 Fert Drop Tube Box 10 Your kit includes: Qty. Part No. 16 16 32 1 16 10/24/2005 133-065D 800-008C 801-002C 813-033C 817-346C Part Description SML SDS TB REINFORCEMENT CLAMP HOSE 1 1/2 NO. 24 SCREW HEX SLT 10-16 X 1/2P.