Operator’s/Parts Manual Unit Mount Conservation Coulter and Spring Package Attachment for JD 7000, JD 7200, White 6100 , Kinze Planters and Great Plains Row Units Planting Components ! Read the operator’s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! 12757 Cover illustration may show optional equipment not supplied with standard unit.
Table of Contents General Information . . . . . . . . . . . . . . . . . . . . . . . . .1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Using this Manual . . . . . . . . . . . . . . . . . . . . . . . . .2 Important Safety Information . . . . . . . . . . . . . . . . . .3 Owner’s Assistance . . . . . . . . . . . . . . . . . . . . . . . . .4 Operating and Assembly Instructions . . . . . . . . . . .5 General Operation & Repair . . . . . . . . . . . . . . . . .
General Information 1 General Information Important Notice Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied, while every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc.
2 Introduction Great Plains welcomes you to its growing family of new product owners. This Conservation Coulter and Spring Package has been designed with care and built by skilled workers using quality materials. Proper setup, maintenance and safe operating practices will help you get years of satisfactory use from the machine. Description of Unit The parts on your Conservation Coulter and Spring Package have been specially designed and should only be replaced with genuine Great Plains parts.
Important Safety Information 3 Important Safety Information Look for Safety Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it.
4 Owner Assistance If you need customer service or repair parts, contact a Great Plains dealer. They have trained personnel, repair parts and equipment specially designed for Great Plains products. Your machine’s parts were specially designed and should only be replaced with Great Plains parts. Always use the model number when ordering parts from your Great Plains dealer.
Operating and Assembly Instructions 5 Operating and Assembly Instructions Most accidents are the result of negligence and carelessness, usually caused by failure of the operator to follow simple but necessary safety precautions. The following safety precautions are suggested to help prevent such accidents. The safe operation of any machinery is a big concern to consumers and manufactures.Your Conservation Coulter and Spring Package has been designed with many built-in safety features.
6 Assembly Instructions Conservation Coulter Installation For Great Plains , JD 7000, White 6100 & Kinze Down Pressure Spring Kit Installation Refer to Illustration on Page 10 For Great Plains and JD 7200 1. Bolt bracket (11) to planter unit using 1/2” x 1 1/2” long carriage bolts (22), flat washers (21), lock spring washers (18), and hex nuts (17) for the top two holes. Use 1/2” x 1 1/2” long bolt (25), 1/2” USS flat washers (24), and 1/2” hex flange nut (23) for the bottom hole.
Operating and Assembly Instructions 7 Upper Spring Mount Installation For Great Plains and JD 7200 1. Raise the planter and support it with safety blocks in order to continue. Attach adjustment bar (5) to the two supports (7) using the clevis pin (8) and the hair pin (9). Bolt this assembly to the back of the mounting plate using 3/8" x 1" long carriage bolt (10), 3/8" flat washer (11), and 3/8" hex flange nut (11). 2. Slip springs (2) and spacers (3) over handle adjustment assembly (1). 3.
8 Adjustments Coulter Adjustments Refer to Illustration on Page 10 or 12 1. To adjust the coulter vertically, loosen the 3/4" jam nut (7), and the 3/4" x 3" long hex bolt (12). 2. By turning the recessed nut, rotate the cam casting (9) to set the desired height. Each increment on the casting (9) represents approximately 1/4" of vertical adjustment. 3. Tighten the bolt (12) and jam nut (7). Check and tighten all nuts and bolts.
Maintenance and Lubrication 9 Maintenance and Lubrication Maintenance Proper servicing and adjustment is the key to the long life of any farm implement. With careful and systematic inspection, you can avoid costly maintenance, time and repair. After using your Conservation Coulter and Spring Package for several hours, check all bolts to be sure they are tight. 1. Listed below are the items you need to lubricate every 20 hours of operation.
10 Parts Conservation Coulter Assembly for Great Plains, JD 7000, White 6100 and Kinze 12758 204-328M 7/31/2002
Parts 11 Ref. Part No. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
12 Conservation Coulter Assembly for Great Plains and JD 7200 12136 204-328M 7/31/2002
Parts 13 Ref. Part No. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
14 Down Pressure Spring Assembly for John Deere 7000, White 6100 and Kinze 11314 204-328M 7/31/2002
Parts 15 Ref. Part No. Description 1. 2. 3. 4. 5. 6. 7. 8. 9.
16 Down Pressure Spring Package Assembly for John Deere 7200 12135 204-328M 7/31/2002
Parts 17 Ref. Part No. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 204-336S 807-103C 204-205D 801-009C 204-334H 802-058C 204-223D 805-086C 805-010C 802-015C 803-209C 800-111C 204-212D 204-206D 804-019C 204-125H 805-073C 807-104C 204-221D 802-058C HANDLE ADJUSTMENT ASSEMBLY SPRING EXT 1 5/8ODX11.8LGX.225 SPACER SCREW SET 1/4-28 SH X 1/2 LG ADJUSTMENT BAR WELDMENT HHCS 5/8-11X2 1/2 GR5 PIVOT ROD SUPPORT PIN CLEVIS 3/8 X 2 23/64 PLT. PIN HAIR COTTER .
18 Appendix Torque Values Chart Bolt Head Identification Bolt Head Identification Bolt Size (Inches) Grade 2 Grade 5 in-tpi1 N · m2 ft-lb3 N·m 1/4" - 20 7.4 5.6 1/4" - 28 8.5 6 Grade 8 Bolt Size (Metric) 5.8 8.8 Class 5.8 10.9 Class 8.8 Class 10.9 ft-lb N·m ft-lb mm x pitch4 11 8 16 12 M 5 X 0.8 4 3 6 5 9 7 13 10 18 14 M6X1 7 5 11 8 15 11 N·m ft-lb N·m ft-lb N·m ft-lb 5/16 - 18 15 11 24 17 33 25 M 8 X 1.
Appendix 19 Warranty Great Plains Manufacturing, Incorporated warrants to the original purchaser that this seeding equipment will be free from defects in material and workmanship for a period of one year from the date of original purchase when used as intended and under normal service and conditions for personal use; 90 days for commercial or rental purposes.
Great Plains Manufacturing, Inc. Corporate Office: P.O.
