User Manual

ManualsBrandsGreat Plains ManualsHardwareCTA4000HD

Great Plains Mfg., Inc.

Installation Instructions 1

Opener Stop Update

CTA4000HD Air Drill Implements

General Information

These instructions explain how to install an opener stop

update kit on an existing drill that lacks these stops.

The stops reduce the risk of hose entanglement when

the drill is folded.

These instructions apply to an installation of:

One kit updates one drill (several rows on both wings).

Drills manufactured in March 2009 or later require no

kits.

Summary of content (8 pages)

PAGE 1
Great Plains Mfg., Inc. Installation Instructions 1 Opener Stop Update CTA4000HD Air Drill Implements Used with: • CTA4000HD-5010 • CTA4000HD-6575 • CTA4000HD-8006 ! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! General Information These instructions explain how to install an opener stop update kit on an existing drill that lacks these stops.
PAGE 2
Great Plains Mfg., Inc. 2 Opener Stop Update Before You Start Compatibility Refer to Figure 2 1. Check the serial number plate of the drill to ensure it is a compatible model, and serial number. Inventory 2. Make sure all parts are present. Comprehension 3. Review these instructions. Make sure the installers understand where each part or assembly is installed, and what tools are required for the task.
PAGE 3
Great Plains Mfg., Inc. Installation Instructions 3 Install Stops at Rows Insert Stops in Rows Refer to Figure 3 Stop plates 12 are installed in the one of the two slots on both sides of the top rear of the opener frame. 1 12 Which rows receive plates varies by drill model and whether left or right wing. Which slot to use (left or right) is specific to the drill model and row. The placement charts call it out as: Inside Toward drill center. Right slot on left wing. Left slot on right wing.
PAGE 4
Great Plains Mfg., Inc. 4 Opener Stop Update CTA4000HD-6575 (7.5 inch) Placement F R L B 01 03 02 09 07 05 06 04 11 10 08 17 15 13 49 18 16 14 12 51 50 48 57 55 53 54 52 61 59 58 56 60 63 62 Figure 5 Stop Plate Placement for 7.
PAGE 5
Great Plains Mfg., Inc. Installation Instructions 5 Fasten Stops to Rows Refer to Figure 7 9. Select all of: 14 801-025C SCREW HEX 5/16-12X3/4 THD FRM Insert the screw at the opener frame hole aligned with the stop plate tab hole, from the side of the same slot. Drive the self-tapping screw in to a final torque of: 15 foot-pounds (22 N-m) 14 U R F L D B Figure 7 Securing a Stop 29461 Adjust Wing Primary Seed Hose Primary seed hoses on the wings are re-routed to improve clearance.
PAGE 6
Great Plains Mfg., Inc. 6 Opener Stop Update Re-Route Wing Seed Hose Refer to Figure 9 14. Cut the wing tower primary hose out of any tie wraps back to the welded loop at the wing fold point. 15. Re-route the hose along the rear outside of the wing as shown in Figure 9. 16. Re-connect the hose to the re-positioned tower inlets and secure with hose clamp. 17. Secure it to the frame using three ties on each wing. 22¾ in 57.8 cm 22¾ in 57.
PAGE 7
Great Plains Mfg., Inc. Installation Instructions 7 Appendix New Parts This manual covers the installation of two kits. Quantities are units (“ea”). The part call-out numbers in this list match all Figures in these installation instructions. Part descriptions match those in your updated Parts Manual.
PAGE 8
Great Plains Mfg., Inc. 8 Opener Stop Update Great Plains Manufacturing, Inc. Corporate Office P.O.