Manual

ManualsBrandsGreat Plains ManualsHardwareHydraulic Kit

Great Plains Mfg., Inc. Parts Installation Instructions 1

Two-Outlet Hydraulic Kit

2- and 3-Section Drills

Used with drill models:

• 2S-2600/F/HD/HDF

• 3S-3000/F/HD/HDF

• 3S-4000/F/HD/HDF

• 3S-5000/F/HD/HDF

General Information

These instructions explain how to install the Two-Outlet

Hydraulic Kit. This combines the drill’s two Lift circuits

(Opener and Transport) into a single circuit at the hitch.

With this kit, a tractor having only two remotes can

operate a drill which would otherwise require three

circuits.

These instructions apply to:

This kit relies on some existing drill components.

This kit includes some parts not required, depending on

drill vintage, and drill options already present or also

being installed at this time.

If Markers are also to be installed, install the Two-Outlet

Hydraulic Kit ﬁrst.

Notations and Conventions

“Left” and “Right” are facing in the

direction of machine travel. An

orientation rose in the line art

illustrations shows the directions of

Left, Right, Front, Back, Up, Down.

Each kit converts one drill.

Kit Kit Description

194-122A 3S TWO OUTLET TRACTOR HYD. KIT

When you see this symbol, the subsequent instructions and

warnings are serious - follow without exception. Your life

and the lives of others depend on it!

Figure 1

Location of New Valve

15485

single-digit or single-letter callouts identify

components in the currently referenced Figure

or Figures.

two-digit callouts in the range 11 through 24

reference new parts from the list on page 9.

The descriptions match those on the cartons,

bags or item tags, as well as in your updated

Parts Manual.

two-digit callouts in the range 51 through 62

reference affected existing parts from the table

on page 9. The descriptions match those in

your Parts Manual.

11 24

51 62

Summary of content (10 pages)

PAGE 1
Parts Great Plains Mfg., Inc. Installation Instructions 1 Two-Outlet Hydraulic Kit 2- and 3-Section Drills Used with drill models: • 2S-2600/F/HD/HDF • 3S-3000/F/HD/HDF • 3S-4000/F/HD/HDF • 3S-5000/F/HD/HDF When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! General Information These instructions explain how to install the Two-Outlet Hydraulic Kit.
PAGE 2
2-Outlet Selector Front Parts Great Plains Mfg., Inc. Before You Start Review these instructions, and make sure you understand which existing system components are reused, and where they are located. The new components, and the existing components to be re-used or discarded, are located on the tongue of the drill, near the hitch. Inventory the contents per “New Parts: Kit 194-122A” on page 9.
PAGE 3
Great Plains Mfg., Inc. Front Parts Installation Instructions 3 Hydraulic Pressure Relief High Pressure Fluid Hazard: Only trained personnel should work on system hydraulics! Escaping fluid under pressure can have sufficient pressure to penetrate the skin, causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic lines. Use a piece of paper or cardboard, NOT BODY PARTS, to check for leaks.
PAGE 4
2-Outlet Selector Front Parts Great Plains Mfg., Inc. Install Valve Mount If markers are already installed, and a valve is already present at the mount, skip to Step 8 on page 4. 18 U 12 Mount as First Valve 1 Refer to Figure 4 7. Select: one new B R F 12 194-249D BRACKET, 2ND SELECTOR VALVE, D L two new 16 802-168C HHCS 3/8-16X3 1/4 GR5, 16 and two new 18 803-013C NUT LOCK 3/8-16 PLT.
PAGE 5
Front Great Plains Mfg., Inc. Parts Installation Instructions 5 Prepare New Hitch Hoses Two circuits (Transport Lift and Opener Lift), which were intended for direct connection to tractor remote ports, are reconnected to the new selector valve starting at step 19. Any Quick Disconnects (QDs) or hose handles on those hoses are transferred or replaced. The kit includes two new hitch hoses to the tractor. For newer drills (with hose handles), continue at “2012+ Remove/Transfer Hose Handles”.
PAGE 6
2-Outlet Selector Front Parts Great Plains Mfg., Inc. 2011- Remove/Add Quick Disconnects If the drill lift circuits have hose handles, follow the steps at “2012+ Remove/Transfer Hose Handles” on page 5. The new hitch hoses provided in the kit are terminated with MORB fittings. Older drills would have FNPT QDs. The kit includes new FORB QDs. Refer to Figure 7 (new hoses not shown) 14.
PAGE 7
Front Great Plains Mfg., Inc. Parts Installation Instructions 7 Connect Lift Circuit Hoses Refer to Figure 9 (depicting 2012+ hoses - 2011- hoses are MNPT-terminated without adaptors) Note: Do not use thread sealant on JIC or ORB connections. Note: It may be necessary to loosen the FNPTS-MORB adaptors 20 on the valve in order to tighten hose NPT connections without twisting the hoses. Alternatively, hoses can be disconnected at cylinder-end JIC connections. U B R F D L A 20 B 19.
PAGE 8
2-Outlet Selector Front Parts Secure Hoses Great Plains Mfg., Inc. 15 Refer to Figure 10 There are two or four hoses to clamp, requiring one or two clamps. How to clamp them depends on the available hardware. Figure 10 shows the recommended stacking for four possible combinations.
PAGE 9
Front Great Plains Mfg., Inc. Parts Installation Instructions 9 Parts Lists New Parts: Kit 194-122A The part call-out numbers in this list match all Figures in the installation instructions. Your kit includes the following parts.
PAGE 10
2-Outlet Selector Front Parts Great Plains Mfg., Inc. Reference Information Abbreviations AD CP EL GR HG HH HHCS HYD JIC NPT NPTS ORB PLT QD USS Torque Values Adaptor Coupler Elbow Grade Hose Grip Hydraulic Hose Hex Head Cap Screw (Bolt) Hydraulic (Female/Male) Joint Industry Conference 37° flare fittings (Female/Male) National Pipe Thread NPT Swivel (Female/Male) O-Ring Boss Plated Quick Disconnect U.S.