User Manual

2012-08-23 Table of Contents Index 402-382M
Great Plains Manufacturing, Inc. Table of Contents Index 19
Install Valve Blocks
Refer to Figure 18
The air clutches now installed are controlled by solenoid
valves provided in blocks of 4 valves, each valve
controlling a number of rows. A Swath Command™ kit
includes 1, 2 or 3 valve blocks.
The valves are controlled by a WSMB-TCOM
a
. Each
TCOM controls up to eight valves. A Swath Command™
kit includes 1 or 2 WSMBs.
Start at the left side of the planter. Install the valve block
and/or TCOM for each section. A section may have both
components or only a valve block.
118. Select all included WSMB-TCOM bundles:
402-305K DJ 8 CHANNEL TRU-COUNT MOD ASM
If the kit has more than one, arrange them in serial
number order for installation.
Note: The 402-305K bundle includes:
467982000S1 PLNTR CNTRL OUTPUT MODULE(POM)
467983505 DJIA OUTPUT HARN 8-CH TRU-COUN
802-224C HHCS 1/4-20X1 1/4 GR5
804-006C WASHER LOCK SPRING 1/4 PLT
803-006C NUT HEX 1/4-20 PLT
Set each harness aside for later installation.
Note: Connecting WSMBs to the CANbus in serial
number order (page 24) causes them to be
correctly ordered by rows when the seed monitor
detects the configuration change.
119. Consult the clutch layout drawing for the kit
(page 48 through page 132). Note locations of any:
829-140C TRU-COUNT 75713-00 VALVE ASM
467982000S1
PLNTR CNTRL OUTPUT MODULE(POM)
If none, move to the next section.
120. Select one each new:
402-533D TRU-COUNT VALVE MODULE BRACKET
806-073C U-BOLT 3/8-16 X 7 1/32 X 7 7/8
and two new:
803-209C NUT FLANGE LOCK 3/8-16 PLT
At the location shown in the layout, secure the
bracket to the opener tool bar using the
U-bolt and flange lock nuts .
121. If the layout drawing shows a WSMB at the
current location, select the:
467982000S1 PLNTR CNTRL OUTPUT MODULE(POM)
with the lowest serial number, and two sets:
802-224C HHCS 1/4-20X1 1/4 GR5
804-006C WASHER LOCK SPRING 1/4 PLT
803-006C NUT HEX 1/4-20 PLT
Insert the bolts from the top rear of the
bracket . Add the WSMB , with connectors
toward implement center, and secure with lock
washers and nuts . Tighten nuts only to
Grade 2 torque specification.
122. Select one new:
829-140C TRU-COUNT 75713-00 VALVE ASM
and two sets new:
802-004C HHCS 1/4-20X3/4 GR5
804-006C WASHER LOCK SPRING 1/4 PLT
803-006C NUT HEX 1/4-20 PLT
Orient the valve assembly with the port lettering
upright. Secure the valve block to the bracket
with the bolts , lock washers and nuts .
Tighten nuts only to Grade 2 torque specification.
123. Repeat step 119 through step 122 for the next
bracket, if any.
a. Working Set MemBer - Planter Output Module
Figure 18
Valve Block Mount
34084
1
2
3
4
AIR IN
U
D
L
R
B
F
272
218
241
255
195
231
242
237
221
242
237
143
272
218
143
143
218
219
231
242
237
219
218
272
218
195
255
241
195
255 241
218
218
231
242
237
231
195 218
242 237
272
221
242
237
272
195
221 242 237