User Manual

ManualsBrandsGReddy ManualsCarTURBO RELATED: Mitsubishi Eclipse 1995-99 GSX/GST / BOV Kit BRS-307 D32

－1－

Important

ImportantImportant

Important

ＢＲＳ－３０７

ＢＲＳ－３０７ＢＲＳ－３０７

ＢＲＳ－３０７

Ｄ３２

Ｄ３２Ｄ３２

Ｄ３２

Please read the manual carefully before installing and using this

Please read the manual carefully before installing and using this Please read the manual carefully before installing and using this

Please read the manual carefully before installing and using this

product.

product.product.

product.

This product is for off road use only.

This product is for off road use only.This product is for off road use only.

This product is for off road use only.

MAKE MODEL CHASSIS ENGINE YEAR

ＭＩＴＳＵＢＩＳＨＩＥＣＬＩＰＳＥＧＳＴ／ＧＳＸＤ３２／Ｄ３３４Ｇ６３１９９３ − １９９６

APPPLICATION

APPPLICATIONAPPPLICATION

APPPLICATION

：

：：

：

Recirculation Type

※ Attachment to recirculate back to intake is included.

This kit is designed for the vehicle specified above.

Please do not attempt to install this kit on other application.

Instruction Manual

Instruction ManualInstruction Manual

Instruction Manual

Summary of content (7 pages)

PAGE 1
ＢＲＳ－３０７Ｄ３２ Instruction Manual Please read the manual carefully before installing and using this product. This product is for off road use only. MAKE MODEL CHASSIS ENGINE YEAR ＭＩＴＳＵＢＩＳＨＩＥＣＬＩＰＳＥＧＳＴ／ＧＳＸＤ３２／Ｄ３３４Ｇ６３１９９３ − １９９６ APPPLICATION ： Recirculation Type ※ Attachment to recirculate back to intake is included. Important This kit is designed for the vehicle specified above. Please do not attempt to install this kit on other application.
PAGE 2
SAFETY INFORMATION Ｉｍｐｏｒｔａｎｔ ○ This Manual will explain the proper installation procedure of this product. Please read this manual carefully. ○ This manual was created considering the vehicle to be completely factory spec. ○ While using this product, please keep this manual to use as a reference. ○ The notation shown below is used through out this manual. Caution This notation will indicate the important procedures and instructions to prevent accidents and injury.
PAGE 3
Ｉｍｐｏｒｔａｎｔ１． Disconnect the negative terminal of the battery before installation ２． Make sure the engine room has cooled down before installation. ３． Removal and disassemble caution procedure. Please follow the basic manufacturer’s recommended procedure ● Make sure to clean the parts that are reused and replace any parts that are damaged. ４． Installation and reassembly caution ● Clean the parts thoroughly before installing the parts. ● Make sure to replace gaskets with new part.
PAGE 4
PARTS LIST １． BLOW OFF VALVE ×１５． BLOW OFF GASKET ×１２． ×１６． ×１７． EMBLEM BOLT・WASHER ×１３． ADAPTER HOSE ATTACHMENT ３４φ ４．３４φPLUG ×１ ×２ PARTS LIST LIST １２６７３ Installation (1) Disconnect the vacuum hose, recirculation hose and remove the factory air bypass valve. (2) Mount the GReddy Blow Off Valve on to the supplied adaptor using the provided gasket and hardware .
PAGE 5
《Venting out to atmosphere Type》 Type 》 (1) Remover the plastic pipe out of the factory suction pipe and install the provided aluminum plug with factory hose clamp. (2) Install the GReddy Blow Off Valve as shown using the factory hose clamps. (3) Reconnect the vacuum using the factory hose clamps. (4) Stick the emblem‹№6› to the top housing. 《Recirculation Type》 Type 》 (1) Remover the funnel from the GReddy blow off valve and install 34mm Hose Attachment for recirculation type.
PAGE 6
Starting the engine (1) Inspect the installation. Reconnect the negative terminal of the battery and start the engine. (2) Check and make sure that there no air leeks, clearance problems or irregular sound. (3) Lightly rev up the engine couple times to check if the blow off valve is operating. Adjustment after installation If irregular idle or engine stall occurs, loosen the M6 lock nut and turn the adjustment screw to HARD until the problem is eliminated.
PAGE 7
How to change the Attachment The attachment on the GReddy Type RS is interchangeable with discharge funnel or hose attachment. To remove the attachment, turn it counter clock wise, and to install turn it clock wise. When changing the attachment, place the O-ring to the attachment being installed and tighten until the attachment flange meets the blow of body. ※ Apply silicone grease before reinstalling the O-ring.