ETAC Product Data Guide

12
15
FIELD--INSTALLED ACCESSORIES
POLYMER WALL SLEEVES
All polymer wall sleeves are made from a molded
polymer that is designed for strength and durability.
This material has excellent corrosion resistance and a
flammability rating of UL94--5V.
The sleeve surface is textured to prevent shine and
hide scratches. The rib configuration on the sleeve
bottom allows easy chassis removal and aids in
drainage
easy fastening of the sleeve to wall openings. Refer to
Insulated Polymer Wall Sleeve
Part No.: SLEEVE--INSUL--1PK
Gree’s accessory insulated polymer wall sleeve,
with factory--installed insulation, provides superior
sound absorption, reduces heat loss and prevents
sleeve sweating, a condition that can occur when the
outside temperature is cold and the indoor conditions
are warm and humid.
A07633
Corrosion-Protected Polymer Sleeve
Non--Insulated Polymer Wall Sleeve
Part No.: WALL--SLEEVE--1PK
Gree’s accessory non-insulated polymer wall sleeve
provides a superior appearance and protection for
many appli
cations.
For the best performance and longest life, Gree
recommends genuine polymer wall sleeves for all
installations.
dimension drawings in Typical Wall Installation
and Dimension section.
The sleeve’s alpine mist color (a shade of beige)
closely matches the front panel and blends in well
with any inside or outside decor. The polymer wall
sleeve comes in both insulated (factory installed) or
non-insulated, to meet the requirements of every
application.
IMPORTANT For applications where weather
conditions could influence sleeve sweating, a
condition that can occur when the outside
temperature is cold and the indoor conditions are
warm and humid, the Insulated Polymer Wall
Sleeve should be considered.
C
e
r
t
i
f
i
e
d
S
e
a
c
o
a
s
t
P
r
o
t
e
c
t
i
o
n
16 in
42 in
(1067 mm)
(406 mm)
14 7/8 in
(378 mm)
The locating holes in the side and top panels allow for
APPLICATIONS
• Hotels and motels
• Nursing homes and assisted living care
centers
• Offices
• Apartments
• Single--family dwellings
• Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
• Whisper--quiet performance, indoors and out
• No bulky duct system
• No separate equipment room
• No water towers or additional cooling
equipment
• No complex match--up of different HVAC
components
• Less sensitivity to building orientation (sun,
wind, shade)
• Optional architectural grille to permit custom
exterior appearance
I nitial Cost Savings for the Buildin
g Owner
• No
expensive component HVAC system
purchase
• No equipment room or maintenance
engineering staff
• Two--part delivery to minimize on--site
damage
• Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
• No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
• Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
• Individual units allow tenants to choose the
degree of comfort and operating economy.
• Rapid
servicing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
• Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
• Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
• Use an existing sleeve and exterior grille. The
Gree E-TAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see acce
ssory Friedrich
Retrofit Wall Sleeve Adapter).
E-TAC
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree E-TAC will meet your
needs.
The Gree E-TAC Packaged Terminal Air Conditioning
(E-TAC) unit is designed to meet the needs of the
architect, engineer, and contractor. For unit
installation, Gree’s expert support network will assist
in all applicable aspects of the construction project,
from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.