ETAC Product Data Guide

20
FIELD-INSTALLEDACCESSORIES (CONT.)
Air Knight
TheAirKnightbyTopTechisanairtreatmentsystem
not a lter. It drasticallyreduce odors, smoke, mold,
fungi,VOC’s (chemical odors) and bacteria found in
manyrooms.Airbornebacteriaandmoldreductionis
normally in the 90+ percentile.
APPLICATIONS
• Hotels and motels
• Nursing homes and assisted living care
centers
• Offices
• Apartments
• Single--family dwellings
• Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
• Whisper--quiet performance, indoors and out
• No bulky duct system
• No separate equipment room
• No water towers or additional cooling
equipment
• No complex match--up of different HVAC
components
• Less sensitivity to building orientation (sun,
wind, shade)
• Optional architectural grille to permit custom
exterior appearance
I nitial Cost Savings for the Buildin
g Owner
• N
o expensive component HVAC system
purchase
• No equipment room or maintenance
engineering staff
• Two--part delivery to minimize on--site
damage
• Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
• No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
• Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
• Individual units allow tenants to choose the
degree of comfort and operating economy.
• Rapi
d servicing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
• Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
• Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
• Use an existing sleeve and exterior grille. The
Gree E-TAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
ex
tension (see accessory Friedrich
Retrofit Wall Sleeve Adapter).
E-TAC
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree E-TAC will meet your
needs.
The Gree E-TAC Packaged Terminal Air Conditioning
(E-TAC) unit is designed to meet the needs of the
architect, engineer, and contractor. For unit
installation, Gree’s expert support network will assist
in all applicable aspects of the construction project,
from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.
Air Knight Plug-In
PartNo.:RGF-PIP-16-GA.
The Air Knight Plug-In, plugs directly into a wall
outletandcanbeusedwithorwithoutitsinternalfan.
Becauseithasitsownoutletsaspartoftheunit,youdo
not lose the wall outlet.
Air Knight PTAC
PartNo:TT-AKPTAC
TheAir Knight PTAC mounts inside the E-TAC air
discharge stream. The indoor fan delivers air treatment
quietly and affectively into the room. The PTAC Air
Knightisneverlostormisplacedsinceitis installed 
in the unit.
Air Knight Plug In
Air Knight PTAC
APPLICATIONS
• Hotels and motels
• Nursing homes and assisted living care
centers
• Offices
• Apartments
• Single--family dwellings
• Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
• Whisper--quiet performance, indoors and out
• No bulky duct system
• No separate equipment room
• No water towers or additional cooling
equipment
• No complex match--up of different HVAC
components
• Less sensitivity to building orientation (sun,
wind, shade)
• Optional architectural grille to permit custom
exterior appearance
I nitial Cost Savings for the Buildin
g Owner
• N
o expensive component HVAC system
purchase
• No equipment room or maintenance
engineering staff
• Two--part delivery to minimize on--site
damage
• Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
• No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
• Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
• Individual units allow tenants to choose the
degree of comfort and operating economy.
• Rapi
d servicing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
• Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
• Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
• Use an existing sleeve and exterior grille. The
Gree E-TAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
ex
tension (see accessory Friedrich
Retrofit Wall Sleeve Adapter).
E-TAC
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree E-TAC will meet your
needs.
The Gree E-TAC Packaged Terminal Air Conditioning
(E-TAC) unit is designed to meet the needs of the
architect, engineer, and contractor. For unit
installation, Gree’s expert support network will assist
in all applicable aspects of the construction project,
from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.
Lateral Duct Kit
Part No.: LATERAL-DUCT (Adapter Plenum and
Extension)
The accessory lateral duct kit allows one unit to heat
or cool two rooms. The kit provides substantial sav-
ings for apartments, hotel suites, and office suites by
eliminating the need for separate units for every room.
The amount of air that can be diverted to an adjoining
room is adjustable from 20 to 25 percent.
The lateral duct kit consists of two main components,
the plenum and the extension duct. The kit mounts to
the wall sleeve and allows either right or left side duct-
ing. Consider the following when designing a ducted
application.
•The maximum extension of the duct length is 4 feet.
•The duct run must be straight and horizontal; no
bends or turns.
•The minimum recommended clearance between the
unit and the adjoining room wall is 6 inches.
•You must provide for return air from the adjoining
room.
NOTES:
1. Lateral duct kit includes wall register for duct exten-
sion and a molding kit to trim the wall opening.
2. The sleeve should extend a minimum of 3-in. into
the adjacent room to
install mounting brackets.
Lateral Duct Kit