ETAC Product Data Guide

44
Hardwire kit (PN: HARDWIRE-KIT-xxxV)
shall be required if an accessory power cord
is not used. The hardwire kit provides a
permanent connection to the unit and shall have
36” (914 mm) of flexible steel conduit and a
plug-in connector for easy connect/disconnect.
Insulated Polymer Wall Sleeve (PN:
SLEEVE-INSUL-1PK) shall be made from a
molded polymer, with factory installed
insulation and a minimum flammability rating
of UL94-5V. The sleeve surface shall be
textured to prevent shine and hide scratches.
45
J. Front Panel (supplied with chassis): Front
panel shall be constructed of a polymer material to
resist breakage and corrosion. It shall have a front
louvered surface with integrated control door and
air filters. The air filters shall be easily accessible
without removing the front panel from the chassis.
K. Air Filters: The chassis shall contain air filters,
with a minimum of 40% arrestance per ASHRAE
Standard 52.1. Two easily accessible front access
supply air filters, shall be interchangeable,
washable and permanent type. The vent filter shall
beaone--piece, removable a
nd washable type
filter.
L. Bi--Directional Discharge Grille: Bi--directional
polymer discharge grille shall resist corrosion and
breakage. It shall be easily set to direct air at 40
degrees from horizontal or 80 degrees from
horizontal. This non--metallic discharge grille
shall be cool to the touch during the heating cycle.
M.Ventilation: The chassis shall have a manual
adjustable fresh air vent with a concealed manual
control. The vent control shall allow a maximum
of up to 65 CFM of fresh air to be drawn into the
room when the indoor fan is operating and the
door is open.
N. High Efficiency Condensate Removal System:
The chassis shall haveacondensate removal
system consisting of a slinger ring integrated in
the outdoor fan, to disperse condensate onto the
condenser coil to be evaporated.
O. Accessories:
1.
2.
3. Deep Wall Metal Wall Sleeve (up to 28” /
711.2 mm.) (PN: SLEEVE--EXTxx--1PK) shall
beaone-- piece, extended wall sleeve, with
factory installed insulation and deep wall
baffles integrated.
4. Sleeve Molding (PN: SLEEVE--MOLDING)
shall trim the wall sleeve to the existing wall to
hide wall joints and irregularities due to the
sleeve opening.
5. Architectural Grille
(PN:GRILLE--PLA--xxxxx or
GRILLE--ALU--xxxxx)
shall be polymeric for long
durable life or painted aluminum for a superior
color match to the building.
6.
7.
Drain Kit (PN: DRAIN-KIT-1PK): This
universal drain kit shall be used internally or
externally to route excess condensate to a central
drainage system. The drain kit include both a
straight tube and a 90˚bend tube.
8.
GA
Wall Thermostats
A. Wireless Wall Thermostat (PN: TT-N631W)
The wireless digial wall thermostat and receiver
module provide maximum temperature control
without pulling wires. The non-programmable
wall thermostat comes complete with LCD
display, backlighting and two speed fan
control.
B. Wired Wall Thermostats (PN: TT-N-411 &
PN: TT-N-421) The digital wall thermostat shall
have a large LCD display with backlighting,
operate with 24VAC, be non-programmable,
easy to use and provide maximum guest comfort.
APPLICATIONS
• Hotels and motels
• Nursing homes and assisted living care
centers
• Offices
• Apartments
• Single--family dwellings
• Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
• Whisper--quiet performance, indoors and out
• No bulky duct system
• No separate equipment room
• No water towers or additional cooling
equipment
• No complex match--up of different HVAC
components
• Less sensitivity to building orientation (sun,
wind, shade)
• Optional architectural grille to permit custom
exterior appearance
I nitial Cost Savings for the Buildin
g Owner
• No expensive component HVAC system
purchase
• No
equipment room or maintenance
engineering staff
• Two--part delivery to minimize on--site
damage
• Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
• No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
• Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
• Individual units allow tenants to choose the
degree of comfort and operating economy.
• Rapid servicing reduces downtime: complete
chassi
s can be replaced in minutes without
disrupting other occupants.
• Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
• Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
• Use an existing sleeve and exterior grille. The
Gree E-TAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see accessory Friedrich
Retr
ofit Wall Sleeve Adapter).
E-TAC
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree E-TAC will meet your
needs.
The Gree E-TAC Packaged Terminal Air Conditioning
(E-TAC) unit is designed to meet the needs of the
architect, engineer, and contractor. For unit
installation, Gree’s expert support network will assist
in all applicable aspects of the construction project,
from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.
APPLICATIONS
• Hotels and motels
• Nursing homes and assisted living care
centers
• Offices
• Apartments
• Single--family dwellings
• Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
• Whisper--quiet performance, indoors and out
• No bulky duct system
• No separate equipment room
• No water towers or additional cooling
equipment
• No complex match--up of different HVAC
components
• Less sensitivity to building orientation (sun,
wind, shade)
• Optional architectural grille to permit custom
exterior appearance
I nitial Cost Savings for the Buildin
g Owner
• No expensive component HVAC system
purchase
• No
equipment room or maintenance
engineering staff
• Two--part delivery to minimize on--site
damage
• Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
• No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
• Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
• Individual units allow tenants to choose the
degree of comfort and operating economy.
• Rapid servicing reduces downtime: complete
chassi
s can be replaced in minutes without
disrupting other occupants.
• Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
• Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
• Use an existing sleeve and exterior grille. The
Gree E-TAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see accessory Friedrich
Retr
ofit Wall Sleeve Adapter).
E-TAC
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree E-TAC will meet your
needs.
The Gree E-TAC Packaged Terminal Air Conditioning
(E-TAC) unit is designed to meet the needs of the
architect, engineer, and contractor. For unit
installation, Gree’s expert support network will assist
in all applicable aspects of the construction project,
from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.
230V Receptacle Module (PN: PTAC-
REC-230Vxx-A): 208/230V outlet receptacle
module (available in 15, 20, or 30amp
configurations) that mounts in the subbase.
Subbase (PN: PTAC-SUBBASE-A): Non-
electrical subbase shall provide mechanical
support and adjustable legs for leveling.
the subbase. Access electrical modules below:
Disconnect Switch (PN: PTAC-SWITCH-A):
Two (2) pole power disconnect switch (DPST)
module that mount in the subbase.
Fuse Protection (PN: PTAC-FUSE-xxA):
Fuse module (available in 15, 20, or 30amp)
provides in-line over-current protection. The
module mounts in the subbase and contains a
cartridge-style fuse.
265V Receptacle Module (PN: PTAC-
REC-265Vxx-A): 265V outlet receptacle
module (available in 15, 20, or 30amp
configurations) that mounts in the subbase.