ETAC Product Data Guide

9
12
SEAMLESS BASEPAN
Seamless drawn basepan add protection against water
accumulation resulting from storm-driven rain with
heavy wind. Gree’s deep basepan hold up to 1-3/4
gallons (6.6 liters) of water without spilling.
CONDENSATE DRAIN VALVE
The temperature--activated drain valve opens when
the outdoor temperature drops below 55˚ F (12.8˚ C)
to prevent water from freezing in the basepan.
A07550
Condensate Drain Valve Prevents Water
from Freezing in Basepan
CONDENSATE REMOVAL
SLINGER
RING
CONDENSER SECTION
A07678
Condensate Removal System
GA
Gree’s E-TAC has a new condensate (water) disposal
system. The suction pull, along with the slinger ring,
draws in water which is sprayed up onto the outdoor
coil. The water then evaporates, thus providing better
disposal of excess condensate and improving unit
efficiency.
NOTE: If it is necessary to control 100% of the
condensate, the Drain Kit (Part No.: DRAIN-KIT-1PK)
is recommended.
LCDI
POWER CORD PROTECTION
The power cord for the 208/230 volt unit
provides LCDI protection by automatically
disconnecting power during an unsafe condition.
Power can be be restored by pressing the RESET
button.
A07551
LCDI Power Cord Plug Head
APPLICATIONS
• Hotels and motels
• Nursing homes and assisted living care
centers
• Offices
• Apartments
• Single--family dwellings
• Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
• Whisper--quiet performance, indoors and out
• No bulky duct system
• No separate equipment room
• No water towers or additional cooling
equipment
• No complex match--up of different HVAC
components
• Less sensitivity to building orientation (sun,
wind, shade)
• Optional architectural grille to permit custom
exterior appearance
I nitial Cost Savings for the Buildin
g Owner
• No
expensive component HVAC system
purchase
• No equipment room or maintenance
engineering staff
• Two--part delivery to minimize on--site
damage
• Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
• No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
• Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
• Individual units allow tenants to choose the
degree of comfort and operating economy.
• Rapid
servicing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
• Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
• Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
• Use an existing sleeve and exterior grille. The
Gree E-TAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see acce
ssory Friedrich
Retrofit Wall Sleeve Adapter).
E-TAC
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree E-TAC will meet your
needs.
The Gree E-TAC Packaged Terminal Air Conditioning
(E-TAC) unit is designed to meet the needs of the
architect, engineer, and contractor. For unit
installation, Gree’s expert support network will assist
in all applicable aspects of the construction project,
from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.