ETAC Product Data Guide

ManualsBrandsGREE ManualsOtherETAC12HP265V30ACP

DIMENSIONAL DRAWINGS AND INSTALLAT ION DATA --

NEW CONSTRUCTION (CONT.)

WALL SLEEVE MOUNTING DIMENSIONS FOR STANDARD AND ACCESSORY GRILLES

A07633

Standard Po lymer Non--Insulated Wall Sleeve

Standard Po lymer Insulated Wall Sleeve

42 in

(1067)

16 in

(406)

Available in:

14-3/4 in. (375),

18 in. (457),

24 in. (610),

26 in. (660),

28 in. (711)

Amounts in ( ) = mm

A07381

Standard and Extended Metal Insulated Wall

Sleeve

MAIN STUD

JACK STUD

CRIPPLE

FLOOR

SUB-FLOOR

42 1/8”

16 1/4”

JACK STUDS

HEADER - 4” X 4” (101.6 X 101.6) OR

(2) 2” X 4” (50.8 X 101.6)

(412.8)

(1070.0)

MEASUREMENTS IN ( ) = mm

A07382

Framing and Minimum Wall Sleeve Opening

SIDE

5/8" MIN.

(15.9)

1/2" (12.7) MINIMUM

STAMPED OUTDOOR GRILLE

SIDE

5/8" MIN.

(15.9)

1/2" (12.7) MINIMUM

ARCHITECTURAL GRILLE

STANDARD MOUNT

ALUMINUM OR PLASTIC

Stamped grille thickness 0.75" (9.4)

Architectural grille thickness 1.25" (32)

NOTE: Dimensions in ( ) are in millimeters

A07383A

Wall Sleev e Mo unting (All Models)

16 in

42 in

(1067 mm)

(406 mm)

14 7/8 in

(378 mm)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW

CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC

components

• Less sensitivity to building orientation (sun,

wind, shade)

• Optional architectural grille to permit custom

exterior appearance

I nitial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system

purchase

• No equipment room or maintenance

engineering staff

• Two--part delivery to minimize on--site

damage

• Weather--protected wall sleeve that goes in

place during construction; chassis that slides

in place after construction

• No seasonal changeover required for cooling

or heating -- units are self--contained comfort

systems

Lower Operating Costs and Reliable Comfort

for The Occupant

• Heat pump models offer substantial savings

over models with conventional electric

resistance heaters

• Individual units allow tenants to choose the

degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete

chassis can be replaced in minutes without

disrupting other occupants.

• Each unit operates independently of other

units in the building. No dependency by

building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve,

your options include:

• Replace the existing wall sleeve with the

the polymer wall sleeve. See accessory sleeve

section for selecting the correct sleeve for

your application.

NOTE: in most cases, when replacing the

wall sleeve, the exterior grille must also be

replaced.

• Use an existing sleeve and exterior grille. The

Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve

extension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

E-TAC

Whether you are designing a new structure or

replacing packaged terminal air conditioning units in

an existing building, Gree E-TAC will meet your

needs.

The Gree E-TAC Packaged Terminal Air Conditioning

(E-TAC) unit is designed to meet the needs of the

architect, engineer, and contractor. For unit

installation, Gree’s expert support network will assist

in all applicable aspects of the construction project,

from preparing a budget to start-up.

The following major competitors’ wall

sleeves/grilles: Carrier, GE, Amana,

Trane, Friedrich and Bryant, and NO

accessory retrofit kit is required.