Performance And Specification Sheet

ManualsBrandsGree ManualsAir ConditionersPTAC Air Conditioner Cooling Area, Adjustable Air Direction

Hardwire kit (PN: HARDWIRE-KIT-xxA)

shall be required if an accessory power cord

is not used. The hardwire kit provides a

permanent connection to the unit and shall have

36” (914 mm) of flexible steel conduit and a

plug-in connector for easy connect/disconnect.

Insulated Polymer Wall Sleeve (PN:

SLEEVE-INSUL-1PK) shall be made from a

molded polymer, with factory installed

insulation and a minimum flammability rating

of UL94-5V. The sleeve surface shall be

textured to prevent shine and hide scratches.

J. Front Panel (supplied with chassis): Front

panel shall be constructed of a polymer material to

resist breakage and corrosion. It shall have a front

louvered surface with integrated control door and

air filters. The air filters shall be easily accessible

without removing the front panel from the chassis.

K. Air Filters: The chassis shall contain air filters,

with a minimum of 40% arrestance per ASHRAE

Standard 52.1. Two easily accessible front access

supply air filters, shall be interchangeable,

washable and permanent type. The vent filter shall

beaone--piece, removable a

nd washable type

filter.

L. Bi--Dir

ectional Discharge Grille: Bi--directional

polymer discharge grille shall resist corrosion and

breakage. It shall be easily set to direct air at 40

degrees from horizontal or 80 degrees from

horizontal. This non--metallic discharge grille

shall be cool to the touch during the heating cycle.

M.Ventilation: The chassis shall have a manual

adjustable fresh air vent with a concealed manual

control. The vent control shall allow a maximum

of up to 65 CFM of fresh air to be drawn into the

room when the indoor fan is operating and the

door is open.

N. High Efficiency Condensate Removal System:

The chassis shall h

aveacondensate removal

system consisting of a slinger ring integrated in

the outdoor fan, to disperse condensate onto the

condenser coil to be evaporated.

O. Accessories:

3. Deep Wall Metal Wall Sleeve (up to 28” /

711.2 mm.) (PN: SLEEVE--EXTxx--1PK) shall

beaone-- piece, extended wall sleeve, with

factory installed insulation and deep wall

baffles integrated.

4. Sleeve Molding (PN: SLEEVE--MOLDING)

shall trim the wall sleeve to the existing wall to

hide wall joints and irregularities due to the

sleeve opening.

5. Architectural Grille

(PN:GRILLE--PLA--xxxxx or

GRILLE--ALU--xxxxx)

shall be polymeric for long

durable life or painted aluminum for a superior

color match to the building.

6. Subbase (PN: PTAC-SUBBASE-A)

— Non- electrical subbase: Th

non-electrical subbase shall provide

mechanical support and requires no

wiring.

— Electrical subbase: The electrical

subbase shall include subbase

(PN: PTAC-SUBBASE-A) for

support and an electrical junction

box (PN: PTAC-REC-xxxVxx-A)

containing a receptacle for corded units.

7. Drain kit (PN: DRAIN--KIT--1PK): This

universal drain kit shall be used internally or

externally to route excess condensate to a

drainage system. It can be field-installed on any

wall sleeve. The drain kit shall be attached to the

to the exterior right or left side of the wall

sleeve for external draining or may be mounted

to the bottom of the wall sleeve for internal

draining. The drain kit shall include both a

straight tube and a 90˚

bend tube.

Wall Thermostats

A. Wireless Wall Thermostat (PN: TT-N-631W)

The wireless digital wall thermostat and receiver

module provide maximum temperature control

without pulling wires. The non-programmable

wall thermostat comes complete with LCD

display, backlighting and two speed fan control.

B. Wired Wall Thermostats (PN: TT-N-411 &

PN: TT-N-421) The digital wall thermostat shall

have a large LCD display with backlighting,

operate with 24VAC, be non-programmable,

easy to use and provide maximum guest comfort.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW

CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC

components

• Less sensitivity to building orientation (sun,

wind, shade)

• Optional architectural grille to permit custom

exterior appearance

I nitial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system

purchase

• No equipment room or maintenance

engineering staff

• Two--part delivery to minimize on--site

damage

• Weather--protected wall sleeve that goes in

place during construction; chassis that slides

in place after construction

• No seasonal changeover required for cooling

or heating -- units are self--contained comfort

systems

Lower Operating Costs and Reliable Comfort

for The Occupant

• Heat pump models offer substantial savings

over models with conventional electric

resistance heaters

• Individual units allow tenants to choose the

degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete

chassis can be replaced in minutes without

disrupting other occupants.

• Each unit operates independently of other

units in the building. No dependency by

building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve,

your options include:

• Replace the existing wall sleeve with the

the polymer wall sleeve. See accessory sleeve

section for selecting the correct sleeve for

your application.

NOTE: in most cases, when replacing the

wall sleeve, the exterior grille must also be

replaced.

• Use an existing sleeve and exterior grille. The

Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve

extension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

E-TAC

Whether you are designing a new structure or

replacing packaged terminal air conditioning units in

an existing building, Gree E-TAC will meet your

needs.

The Gree E-TAC Packaged Terminal Air Conditioning

(E-TAC) unit is designed to meet the needs of the

architect, engineer, and contractor. For unit

installation, Gree’s expert support network will assist

in all applicable aspects of the construction project,

from preparing a budget to start-up.

The following major competitors’ wall

sleeves/grilles: Carrier, GE, Amana,

Trane, Friedrich and Bryant, and NO

accessory retrofit kit is required.