Performance and Specifications
33
EXPANDE D RATING DATA
COOLING PERFORMANCE - HEAT PUMP MODELS
ALL 7,000 NORMINAL BTUH MODELS ALL 9,000 NORMINAL BTUH MODELS
Evaporator entering air temp (D.B.) = 80 deg F Evaporator entering air temp (D.B.) = 80 deg F
277626277626
BtuH 8062 8709 9055 BtuH 9423 10179 10584
Kw 536 531 522 Kw 670 663 653
Amps 2.4 2.3 2.3 Amps 3.1 3.1 3.1
SHR 0.96 0.72 0.53 SHR 0.89 0.66 0.49
BtuH 7500 8131 8624 BtuH 8766 9504 10080
Kw 582 575 569 Kw 727 718 711
Amps 2.5 2.5 2.5 Amps 3.3 3.3 3.3
SHR 0.98 0.74 0.54 SHR 0.91 0.69 0.5
BtuH 6815 7700 8285 BtuH 7965 9000 9684
Kw 640 640 640 Kw 800 800 800
Amps 2.8 2.8 2.8 A
mps 3.7 3.7
3.7
SHR 0.99 0.77 0.54 SHR 0.91 0.71 0.5
BtuH 6075 6892 7762 BtuH 7101 8055 9072
Kw 693 691 692 Kw 866 864 865
Amps 3.0 3.0 3.0 Amps 4.0 4.0 4.0
SHR 0.99 0.81 0.55 SHR 0.92 0.75 0.51
BtuH 5251 5944 6907 BtuH 6138 6948 8073
Kw 758 755 755 Kw 947 943 943
Amps 3.3 3.3 3.3 Amps 4.4 4.3 4.3
SHR 0.99 0.87 0.58 SHR 0.91 0.8 0.54
ALL 12,000 NORMINAL BTUH MODELS ALL 15,000 NORMINAL BTUH MODELS
Evaporator entering air temp (D.B.) = 80 deg F Evaporator entering air temp (D.B.) = 80 deg F
277626277626
BtuH 12564 13572 14112 BtuH 15182 16400 17052
Kw 939 928 914 Kw 1240 1227 1208
Amps 4.3 4.2 4.2 Amp
s 5.5 5.5
5.4
SHR 0.89 0.66 0.49 SHR 0.88 0.65 0.48
BtuH 11688 12672 13440 BtuH 14123 15312 16240
Kw 1018 1006 996 Kw 1345 1329 1316
Amps 4.6 4.6 4.5 Amps 5.9 5.9 5.9
SHR 0.91 0.69 0.5 SHR 0.89 0.68 0.49
BtuH 10620 12000 12912 BtuH 12833 14500 15602
Kw 1120 1120 1120 Kw 1480 1480 1480
Amps 5.1 5.1 5.1 Amps 6.6 6.6 6.5
SHR 0.91 0.71 0.5 SHR 0.9 0.7 0.49
BtuH 9468 10740 12096 BtuH 11441 12978 14616
Kw 1213 1210 1211 Kw 1603 1598 1600
Amps 5.5 5.5 5.5 Amps 7.1 7.1 7.1
SHR 0.92 0.75 0.51 SHR 0.9 0.74 0.5
BtuH 8184 9264 10764 BtuH 9889 11194 13007
Kw 1326 1320 1320 Kw 1752 1745 1745
Amps 6 6 6 Amps 7.7 7.7 7.7
SHR 0.91 0.8 0.54 SHR 0.9 0.79 0.53
LEGEND
EWB - Entering Wet Bulb
D.B. Dry Bulb
AMP - Total Current
Kw - Total Power
BtuH - Total Cooling Capacity
RH - Relative Humidity
SHR - Senable Heating Ratio
Temp EVAP AIR-EWB (DEG F)
501501
011011
5757
5858
5959
TEMP (DEG F) AIR
ENT COND (40%RH)
TEMP (DEG F) AIR
ENT COND (40%RH)
TEMP (DEG F) AIR
ENT COND (40%RH)
Temp EVAP AIR-EWB (DEG F)
TEMP (DEG F) AIR
ENT COND (40%RH)
Temp EVAP AIR-EWB (DEG F)
110
75
85
95
105
110
Temp EVAP AIR-EWB (DEG F)
75
85
95
105
35
GA
APPLICATIONS
• Hotels and motels
• Nursing homes and assisted living care
centers
• Offices
• Apartments
• Single--family dwellings
• Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
• Whisper--quiet performance, indoors and out
• No bulky duct system
• No separate equipment room
• No water towers or additional cooling
equipment
• No complex match--up of different HVAC
components
• Less sensitivity to building orientation (sun,
wind, shade)
• Optional architectural grille to permit custom
exterior appearance
I nitial Cost Savings for the Buildin
g Owner
• No expe
nsive component HVAC system
purchase
• No equipment room or maintenance
engineering staff
• Two--part delivery to minimize on--site
damage
• Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
• No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
• Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
• Individual units allow tenants to choose the
degree of comfort and operating economy.
• Rapid servic
ing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
• Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
• Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
• Use an existing sleeve and exterior grille. The
Gree E-TAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see accessor
y Friedrich
Retrofit Wall Sleeve Adapter).
E-TAC
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree E-TAC will meet your
needs.
The Gree E-TAC Packaged Terminal Air Conditioning
(E-TAC) unit is designed to meet the needs of the
architect, engineer, and contractor. For unit
installation, Gree’s expert support network will assist
in all applicable aspects of the construction project,
from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.
APPLICATIONS
• Hotels and motels
• Nursing homes and assisted living care
centers
• Offices
• Apartments
• Single--family dwellings
• Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
• Whisper--quiet performance, indoors and out
• No bulky duct system
• No separate equipment room
• No water towers or additional cooling
equipment
• No complex match--up of different HVAC
components
• Less sensitivity to building orientation (sun,
wind, shade)
• Optional architectural grille to permit custom
exterior appearance
I nitial Cost Savings for the Buildin
g Owner
• No expe
nsive component HVAC system
purchase
• No equipment room or maintenance
engineering staff
• Two--part delivery to minimize on--site
damage
• Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
• No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
• Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
• Individual units allow tenants to choose the
degree of comfort and operating economy.
• Rapid servic
ing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
• Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
• Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
• Use an existing sleeve and exterior grille. The
Gree E-TAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see accessor
y Friedrich
Retrofit Wall Sleeve Adapter).
E-TAC
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree E-TAC will meet your
needs.
The Gree E-TAC Packaged Terminal Air Conditioning
(E-TAC) unit is designed to meet the needs of the
architect, engineer, and contractor. For unit
installation, Gree’s expert support network will assist
in all applicable aspects of the construction project,
from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.