HIGH-WALL DUCTLESS AIR CONDITIONING & HEATING SYSTEM Models: GWH09AB-A3DNA2B GWH12AB-A3DNA2B GWH09AB-D3DNA2D GWH12AB-D3DNA2D GWH18AC-D3DNA2D GWH24AC-D3DNA2D
Thank you for choosing an High-Wall Ductless Air Conditioning & Heating System! You can feel confident in your selection because the same pride in craftsmanship and engineering knowledge that goes into millions of other Gree installed products worldwide has gone into your unit. Please read this owner’s manual carefully before operation and retain it for future reference.
SAFETY PRECAUTIONS Please read the following before operation. Recognize safety information. This is the safety-alert symbol. When you see this symbol on the unit and in instructions or manuals, be alert to the potential for personal injury. Understand these signal words: DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death.
SAFETY PRECAUTIONS Please read the following before operation. WARNING • Disconnect electrical power to the evo+ system before performing any maintenance or cleaning. • Do not attempt to repair the evo+ system yourself. Incorrect repairs may cause electric shock or fire. Contact a qualified service technician for all service requirements. • Do not splice the power cord or use an extension cord. Overheating can occur, causing a fire hazard. • Keep combustible materials away from the unit.
PART NAMES Indoor unit 5 2 6 3 4 Part Name 1. 2. 3. 4. 5. 6. 7. 8. 9.
OPERATION OF WIRELESS REMOTE CONTROLLER REMOTE CONTROLLER OPERATIONS The evo+ universal wireless remote controller is sleek, versatile and allows you to change room temperatures and functions on unit from the palm of your hand. The large LCD display and buttons make it easy-to-understand and easy-to-use. The remote controller may be used for several evo+ units. It can operate the unit from a distance of up to 25 ft. (7.6 m) as long as there are no obstructions.
OPERATION OF WIRELESS REMOTE CONTROLLER Signal Transmitter ON/OFF Button FAN Button MODE Button 6
OPERATION OF WIRELESS REMOTE CONTROLLER REMOTE CONTROLLER FUNCTIONS CLOCK Button • Press the CLOCK button to enter Clock Setup Mode. The clock icon will begin flashing. Set the clock by pressing the + or - buttons. Press once for slow adjustment; press and hold down for fast adjustment. When finished, press the CLOCK button to save your clock settings. Note that this is the current time, not the timer setting.
OPERATION OF WIRELESS REMOTE CONTROLLER – Button + Button CLOCK Button X-FAN Button TURBO Button LIGHT Button 8
OPERATION OF WIRELESS REMOTE CONTROLLER TIMER ON Button • Press the TIMER ON button to enter TIMER mode. The TIMER ON icon will begin flashing. Set the time period when the unit will turn on by pressing the + or - buttons. Press once for slow adjustment and hold down for fast adjustment. TIMER OFF Button • Press the TIMER OFF button to enter TIMER mode. The TIMER OFF icon will begin flashing. Set the time period when the unit will turn off by pressing the + or - buttons.
OPERATION OF WIRELESS REMOTE CONTROLLER I FEEL Button VERTICAL SWING LOUVER Button TIMER ON Button TIMER OFF Button SLEEP Button 10
OPERATION OF WIRELESS REMOTE CONTROLLER The wireless remote controller is the interface between the user and the evo+ system. Commands are entered by the user to control the system. Any command that has been entered with the remote controller will remain in memory until it is changed by the user or the batteries are replaced. When entering commands, point the remote controller in the direction of the LED display on the front panel.
OPERATION OF WIRELESS REMOTE CONTROLLER MODE BUTTON Use the “MODE” button to select one of the available modes. The selected mode will be displayed on the remote controller and the appropriate light will illuminate on the display panel. AUTO – Unit will automatically select heating or cooling to maintain room temperature between 68°F and 77°F. The remote controller will display the Auto Mode icon with no setpoint. The front panel display will show "77.
OPERATION OF WIRELESS REMOTE CONTROLLER VERTICAL SWING LOUVERS • Press the Vertical Swing Louver button to select five different vertical (up & down) air discharge directions including Continuous Sweep. The Vertical Swing Louver icon will be displayed. Press this button to set swing angle, which circularly changes as below: 0 1 2 3 4 Swing Louver Display OFF 8 7 6 5 Indicates louver swings back and forth in the five places, as shown in the figure.
OPERATION OF WIRELESS REMOTE CONTROLLER TURBO MODE The desired setpoint, either in heating or cooling, can be achieved faster if TURBO mode is used. After selecting the “HEAT” or “COOL” mode button, push the “TURBO” button. The TURBO icon will be displayed on the remote controller and the unit will run at ultra high speed fan. To deactivate the feature, push the “TURBO” button again. The unit will return to normal operation.
OPERATION OF WIRELESS REMOTE CONTROLLER CHANGING BATTERIES AND ADDITIONAL NOTES To change batteries, slide cover off battery compartment on back of remote controller. Remove and safely discard old batteries. Insert two new AAA 1.5V dry batteries, using correct polarity. Reattach back cover. NOTE: • If the remote controller will not be used for a long time, remove batteries to prevent leakage damage. • Be sure to aim the remote controller at the receiver of the main unit when operating.
SYSTEM FUNCTIONS TIME GUARD The evo+ System is equipped with many system safeties to provide safe, reliable operation and comfort. The Time Guard function prevents rapid cycling of the compressor. The system has a protective 3-minute time delay to restart the compressor after it has turned off. INTELLIGENT DEFROST The evo+ Intelligent Defrost function increases room comfort and saves energy by eliminating unnecessary defrost cycles.
CARE AND CLEANING WARNING CAUTION CAUTION WARNING • Turn off power and disconnect unit from power source before cleaning. Failure to do so could cause electric shock. • Never spray water on either indoor or outdoor unit. This could cause damage or unit failure. • Never use abrasive cleaners on indoor or outdoor unit. Use only slightly damp, clean, soft cloth or very mild cleansers. CLEANING THE FRONT PANEL 1. To remove front panel for cleaning, lift up and pull out. 2.
CARE AND CLEANING CLEANING THE PRIMARY AIR FILTER Cleaning is recommended every three months. NOTE: If the indoor unit is exposed to excessive dust, cleaning may be necessary more often. Use caution when removing the filter to avoid sharp metal extensions. 1. Remove air filter by tilting up the unit cover and pulling filter free. 2. Clean air filter using a vacuum or warm water and mild cleaner. Air dry filter in the shade. Never use fire to clean stains or debris on filter. 3.
TROUBLESHOOTING WARNING CAUTION WARNING WARNING Do not attempt any repairs on the unit yourself. Incorrect repair can cause shock or fire. Always call a qualified service professional. Using these troubleshooting suggestions can save time when you contact the qualified service professional. PROBLEM CAUSE/SOLUTION System does not restart. Cause: Solution: Indoor unit emits unpleasant odor when started. Cause: Solution: You hear a “water flowing” sound.
TROUBLESHOOTING PROBLEM CAUSE/SOLUTION Wireless remote controller lost or does not work. Cause: Solution: There are a number of possible reasons. Check the following: • The batteries might be low. Change the batteries. • The remote controller must be within 25 ft. (7.6 m) with no obstructions of the indoor unit. If remote controller is lost or damaged and needs to be replaced, contact your qualified service professional for assistance.
SYSTEM OPERATION COOLING OPERATION How it works: In cooling mode, your evo+ indoor unit will absorb heat from the room, then the evo+ outdoor unit will discharge the heat to the outdoors. The evo+ cooling capacity decreases as the outdoor temperature increases. This causes the evo+ to work harder and longer to hold the selected room temperature.
ENERGY SAVING TIPS 1. Relaxing room temperature at night is OK: During the nighttime hours you don't require the same level of conscious cooling or heating. Try using Sleep Mode to gradually relax room temperature and allow the unit to run less and save energy. 2. Curtains and shades: In the summer, you need to block the effects of the sun. Close window curtains and shades on the south and west side of your home to help block solar heat. In winter, the sun is your friend.
GREE ELECTRIC APPLIANCES, INC. www.greecomfort.com LIMITED WARRANTY GREE distributor (hereinafter “Company”) warrants this product against failure due to defect in materials or workmanship under normal use and maintenance as follows. All warranty periods begin on the date of original installation. If the date cannot be verified, the warranty period begins one hundred twenty (120) days from date of manufacture.