Service Manual
Table Of Contents
- 目录
- 第一部分 产品篇
- 第二部分 控制篇
- CONTROL
- 1 OPERATION FLOWCHART
- 2 WIRELESS REMOTE CONTROLLER
- 3 WIRED CONTROLLER
- 4 OPERATION INSTRUCTION OF SPECIAL FUNCTIONS
- 4.1 Setting of Filter Clean Reminder Function
- 4.2 Low Temperature Drying Function
- 4.3 Lock Function
- 4.4 Memory Function
- 4.5 Door Control Function/Human Sensitive Function
- 4.6 Switch between Fahrenheit and Centigrade
- 4.7 Enquiry of Ambient Temperature
- 4.8 Enquiry of Historical Malfunction
- 4.9 Debugging Function
- 4.9.1 Setting ambient temperature sensor (dual ambient temperature sensors function)
- 4.9.2 Selecting three speeds in high speed and three speeds in low speed of indoor fan motor
- 4.9.3 Displaying setting of freeze protection error code
- 4.9.4 Setting refrigerant lacking protection function
- 4.9.5 Selecting blowing residual heating of indoor unit
- 4.9.6 Mode selecting of compressor electric heating belt
- 4.9.7 Selecting low-power consumption mode
- 4.9.8 Selecting door control function
- 4.9.9 Selecting human sensitive function
- 4.9.10 Selecting long-distance monitoring or centralized controller
- 4.9.11 Selecting fan mode of indoor fan motor
- 4.9.12 Selecting compensation of temperature sensor at air return
- 5 INSTALLATION OF WIRED CONTROLLER
- 6 TROUBLESHOOTING
- 7 CENTRALIZED CONTROLLER
- 7.1 Smart Zone Controller
- 7.2 Additional Special Functions
- 7.2.1 Door control function
- 7.2.2 Human sensitive function
- 7.2.3 MODBUS interface
- 7.2.4 Connect to interface of centralized controller:
- 7.2.5 Light board control:
- 7.2.6 Malfunction output of relay:
- 7.2.7 Reserved fresh air valve interface for duct type unit
- 7.2.8 Interface of anion generator
- 7.2.9 Chassis electric heating belt of outdoor unit is optional
- CONTROL
- 第三部分 安装篇
- INSTALLATION
- 1 INDOOR UNIT INSTALLATION
- 1.1 Installation of Duct Type
- 1.2 Installation of Floor Ceiling Type
- 1.3 Installation of Cassette Type
- 1.3.1 Before Installation
- 1.3.2 Installation Site
- 1.3.3 Installing the Main Body Unit
- 1.3.4 Installing the Suspension Bolts
- 1.3.5 Leveling
- 1.3.6 The Panel Installation
- 1.3.7 Dimension Data
- 1.3.8 Installation of Drain Piping
- 1.3.9 Installing the Drain Pipes
- 1.3.10 Precautions When Doing Riser Piping Work
- 1.3.11 Testing of Drain Piping
- 2 OUTDOOR UNIT INSTALLATION
- 3 REFRIGERATION PIPING WORK
- 3.1 Refrigeration Piping Work Procedures and Caution in Connecting
- 3.2 Specification of Connection Pipe
- 4 ELECTRIC WIRING WORK
- 1 INDOOR UNIT INSTALLATION
- INSTALLATION
- 第四部分 维护篇(上)4.1~4.3
- 第四部分 维护篇(中)4.4拆装
- 第四部分 维护篇(下)4.5爆炸图及清单
U-Match Series DC Inverter Service Manual
33
6 TROUBLESHOOTING
6.1 Display of Error Code
Table 2-6-1 Error Code List
Error Code
Error
E1
Compressor high pressure protection
E2
Freeze protection
E3
Compressor low pressure protection, refrigerant lacking protection, refrigerant
recycling mode
E4
Compressor high discharge temperature protection
E6
Communication malfunction
E8
Malfunction of indoor fan motor
E9
Full water protection
F0
Malfunction of indoor ambient temperature sensor
F1
Malfunction of evaporator temperature sensor
F2
Malfunction of condenser temperature sensor
F3
Malfunction of outdoor ambient temperature sensor
F4
Malfunction of discharge temperature sensor
F5
Malfunction wired controller temperature sensor
C5
Wong dial switch of capacity
EE
Malfunction of outdoor main control memory chip
PF
Malfunction of electric box sensor
H3
Compressor overload protection
H4
Overload protection
H5
IPM protection
H6
Malfunction of DC fan motor
H7
Drive desynchronizing protection
HC
PFC protection
L1
Malfunction of humidity sensor
Lc
Start-up failure
Ld
Compressor phase protection
LF
Power protection
Lp
Models of indoor unit and outdoor unit do not match with each other
U7
Direction changing malfunction of 4-way valve
P0
Drive reset protection
P5
Overcurrent protection
P6
Communication malfunction between main control and drive
P7
Malfunction of drive module sensor
P8
High temperature protection of drive module
P9
Zero-cross protection
PA
AC current protection
PC
Malfunction of drive current
Pd
Sensor connection protection