Service Manual
Table Of Contents
- 目录
- 第一部分 产品篇
- 第二部分 控制篇
- CONTROL
- 1 OPERATION FLOWCHART
- 2 WIRELESS REMOTE CONTROLLER
- 3 WIRED CONTROLLER
- 4 OPERATION INSTRUCTION OF SPECIAL FUNCTIONS
- 4.1 Setting of Filter Clean Reminder Function
- 4.2 Low Temperature Drying Function
- 4.3 Lock Function
- 4.4 Memory Function
- 4.5 Door Control Function/Human Sensitive Function
- 4.6 Switch between Fahrenheit and Centigrade
- 4.7 Enquiry of Ambient Temperature
- 4.8 Enquiry of Historical Malfunction
- 4.9 Debugging Function
- 4.9.1 Setting ambient temperature sensor (dual ambient temperature sensors function)
- 4.9.2 Selecting three speeds in high speed and three speeds in low speed of indoor fan motor
- 4.9.3 Displaying setting of freeze protection error code
- 4.9.4 Setting refrigerant lacking protection function
- 4.9.5 Selecting blowing residual heating of indoor unit
- 4.9.6 Mode selecting of compressor electric heating belt
- 4.9.7 Selecting low-power consumption mode
- 4.9.8 Selecting door control function
- 4.9.9 Selecting human sensitive function
- 4.9.10 Selecting long-distance monitoring or centralized controller
- 4.9.11 Selecting fan mode of indoor fan motor
- 4.9.12 Selecting compensation of temperature sensor at air return
- 5 INSTALLATION OF WIRED CONTROLLER
- 6 TROUBLESHOOTING
- 7 CENTRALIZED CONTROLLER
- 7.1 Smart Zone Controller
- 7.2 Additional Special Functions
- 7.2.1 Door control function
- 7.2.2 Human sensitive function
- 7.2.3 MODBUS interface
- 7.2.4 Connect to interface of centralized controller:
- 7.2.5 Light board control:
- 7.2.6 Malfunction output of relay:
- 7.2.7 Reserved fresh air valve interface for duct type unit
- 7.2.8 Interface of anion generator
- 7.2.9 Chassis electric heating belt of outdoor unit is optional
- CONTROL
- 第三部分 安装篇
- INSTALLATION
- 1 INDOOR UNIT INSTALLATION
- 1.1 Installation of Duct Type
- 1.2 Installation of Floor Ceiling Type
- 1.3 Installation of Cassette Type
- 1.3.1 Before Installation
- 1.3.2 Installation Site
- 1.3.3 Installing the Main Body Unit
- 1.3.4 Installing the Suspension Bolts
- 1.3.5 Leveling
- 1.3.6 The Panel Installation
- 1.3.7 Dimension Data
- 1.3.8 Installation of Drain Piping
- 1.3.9 Installing the Drain Pipes
- 1.3.10 Precautions When Doing Riser Piping Work
- 1.3.11 Testing of Drain Piping
- 2 OUTDOOR UNIT INSTALLATION
- 3 REFRIGERATION PIPING WORK
- 3.1 Refrigeration Piping Work Procedures and Caution in Connecting
- 3.2 Specification of Connection Pipe
- 4 ELECTRIC WIRING WORK
- 1 INDOOR UNIT INSTALLATION
- INSTALLATION
- 第四部分 维护篇（上）4.1~4.3
- 第四部分 维护篇（中）4.4拆装
- 第四部分 维护篇（下）4.5爆炸图及清单
U-Match Series DC Inverter Service Manual
186
19
Front Connection Board
01349408P
1
20
Supporter
26909409
3
21
Rear Side Plate Assy
01319400005
1
22
Fixed Mount
26909426R
1
23
Display Board
30294000009
1
24
Evaporator Assy
01029400049
1
25
Rotating Shaft
26909413
1
26
Connecting Rod
26909411
1
27
Rotating Shaft
26909412
1
28
Stepping Motor
1521240206
1
29
Left Foam Assy
12509408
1
30
Installation Supporting Frame
01809401
1
31
Electric Box Assy
01399400116
1
32
Main Board
30224000029
1
33
Terminal Board
4201025301
1
34
Terminal Board
42010178
1
35
Left Cover Plate
2690941601
1
36
Bracket 1
01809404
1
37
O-Gasket of Bearing
76512404
1
38
Support Of Motor Bearing
01792408
1
39
Centrifugal fan
1041410101
3
40
Clapboard Sub-Assy
01249400002
1
41
Rear Connection board
01349418
1
42
Front Volute Casing
26905208
3
43
Rotary Axis Sub-Assy
73018052
1
44
Joint Slack
73018731
1
45
Motor Support Sub-Assy
01809400029
1
46
Brushless DC Motor
15705200005
1
47
Rear Volute Casing
26909419
3
48
Water Tray Assy
01289405
1
49
Front Grill
26909434
1
50
Top Cover Board Sub-assy
01269405
1
51
Drainage Pipe Sub-assy
05235434
1
Above data is subject to change without notice, pls reference the SP in global service website.