Service and Parts Manual

25
Technical Information
Service Manual
Function introduction for combination buttons
Energy-saving function
1.
2.
according to setting time. ON/OFF button has no ef
fect on setting. If you dont need this function, please use remote controller to cancel it.
Child lock function
3.
8 heating function
4.
Note:
● Under on and of
f status, you can set TIMER OFF or TIMER ON simultaneously.
● Before setting
TIMER ON or TIMER OFF, please adjust the clock time.
●
After starting up TIMER ON or TIMER OFF, set the constant circulating valid. After that, air conditioner will be turned on or turned off
Temperature display switchover function
5.
I FELL Function
press sleep button will cancel energy-saving function. If sleep function has been set under cooling mode, start up the energy-saving
function will cancel sleep function.
Under cooling mode, press "TEMP" and " CLOCK" buttons simultaneously to start up or turn off energy-saving function. When energy-saving
function is started up, "SE" will be shown on remote controller, and air conditioner will adjust the set temperature automatically according to
ex-factory setting to reach to the best energy-saving effect. Press "TEMP" and "CLOCK"buttons simultaneously again to exit ene
rgy-saving
function.
Note:
● Under energy-saving function, fan speed is defaulted at auto speed and it cant be adjusted.
●
Under energy-saving function, set temperature cant be adjusted. Press "TURBO" button and the remote controller wont send signal.
● Sleep function and energy-saving function cant operate at the same time. If energy-saving function has been set under cooling mode,
sleep button will cancel 8
heating function. If sleep function has been set under cooling mode, start up the 8 heating function will
cancel sleep function.
● Under
temperature display, the remote controller will display 46 heating.
Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start
up or turn off 8 heating function. When this function is
started up, " " and "8
" will be shown on remote controller, and the air conditioner keep the heating status at 8 . Press "TEMP"
and
"CLOCK" buttons simultaneously again to exit 8 heating function.
Note:
● Under 8
heating function, fan speed is defaulted at auto speed and it cant be adjusted.
● Under 8
heating function, set temperature cant be adjusted. Press
" TURBO " button and the remote controller wont send signal.
● Sleep function and 8
heating function cant operate at the same time. If 8 heating function has been set under cooling mode, press
Press "▲" and "
▲
" simultaneously to turn on or turn off child lock function. When child lock function is on, " " icon is displayed on
remote
controller. If you operate the remote controller, the " " icon will blink three times without sending signal to the unit.
Under OFF status, press "
▲
" and "MODE" buttons simultaneously to switch temperature display between and .
Operation guide
1.
2.
After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner.
3.
Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT.
4.
Press "▲" or "
▲
" button to set your required temperature. (Temperature cant be adjusted under auto mode).
Press "FAN" button to set your required fan speed: auto, low, medium and high speed.
5. Press "SWING" button to select fan blowing angle.
Press "▲" and "MODE" buttons simultaneously to start I FEEL
function and " " will be displayed on the remote controller. After this function
is
set, the remote controller will send the detected ambient temperature to the controller and the unitwill automatically adjust the indoor
temperature
according to the detected tempera-ture. Press this two buttons simultaneously again to close I FEEL function and " " will
disappea
r.
●
Please put the remote controller near user when this function is set. Do not put the remote controller near the object of high temperature
or
low temperature in order to avoid detecting inaccurate ambient temperature.When I FEEL function is turned on, the remote controller
should be put within the area where indoor unit can receive the signal sent by the remote controller
.