Textron Inc., a subsidiary of Textron Inc. Electric Toothbrush User Manual

Accessories
The fitting and servicing procedures for both types of head are almost identical. Differences are clearly indicated.
IMPORTANT
PRIOR to fitting a swivel head, the base tool must be adapted. See Preparing the base tool opposite.
The air supply must be disconnected when fitting or removing swivel heads.
A Fit Locking Ring 10 over Jaw Spreader Housing 41*
(71210-02101). *See pages 26 and 27.
B Coat Screw 13 with thread locking adhesive and use to
secure Nose Tip 14 onto Body 5.
C Lightly lubricate items 17, 18, 19, 20 and insert into
Jaw Carrier 3 as shown. Secure with Screws 16.
D Position Lever 4 into Body 5 and hold in place with pin
15 through the hole of Body 5 (not a slot).
E Lubricate the sides of the Jaw Carrier Assembly and
insert into Body 5.
F Lubricate Rollers 8 and ENSURE that they will freely
rotate in the holes of Adaptor 9. If necessary ream the
holes.
G Position Spring Clip 7 over Adaptor 9 past the holes for
the rollers and rotate until the locating peg is aligned
with the corresponding hole in Adaptor 9 (smallest
hole).
H Fit Adaptor 9 over the end of Body 5 and drop Rollers 8
into place. Push Spring Clip 7 over Rollers 8.
I Insert Spindle 11 through Adaptor 9 into Jaw Carrier 3
until the hole lines up with slot in Body 5. Temporarily
hold in place with Pin 6.
J Insert Pin 12 through the front slot of Body 5 into Jaw
Carrier 3.
K Hold the assembly vertical to prevent all pins dropping
out and slide the jaw carrier assembly back and forth a
few times to ensure free movement. Go to M
.
L Remove Screws 23 (4 off) and guard 1. On a straight
swivel head also remove Screw 21 and Platform 22.
M Push Pin(s) 6 out and let Spindle 11 drop out. Screw
Spindle 11 onto the Jaw Spreader Housing of the tool,
leaving the small screw fixing hole uppermost for
straight swivel. Tighten gently with a tommy bar.
N Screw the assembly over Spindle 11 onto the tool
handle. Replace Pin(s) 6.
O On straight swivel heads attach Platform 22 onto the
top of the Spindle with Screw 21. Deburr the back end
of Platform 22 so that it cannot catch on Guard 1.
P Snap Guard 1 over the assembly, align screw holes in
guard with tapped holes in body assembly.
Q Insert Pivot Pin 15 through slots in guard and hole in
body. Fit Circlip 2 onto pivot pin so that the circlip seats
in groove provided.
R Coat the thread of Screws 23 (4 off) with thread locking
adhesive and screw into body assembly securing guard
to body assembly.
Swivel Head Fitting Instructions
The following procedure will allow you to assemble and fit either of the swivel heads to the tool. If you order a complete swivel head
rather than individual components, you will only need to start at stage ‘L’.
All moving parts should be lubricated. Unless stated otherwise use Moly Lithium grease (details page 18).
When on grey tint, instructions refer only to the right-angle swivel head. Item numbers in bold refer to illustrations below.
16
1
3
12
14
13
16
6
5
21
22
11
7
9
8
8
8
10
17
18
19
20
STRAIGHT SWIVEL HEAD
2
1
15
9
8
8
10
7
11
17
23
18
19
20
3
16
16
4
12
14
13
6
6
5
RIGHT-ANGLE HEAD
Inc.
16