OWNER’S MANUAL
Welcome NOTE: Read this manual and all important safety instructions before using the unit. Important Safety Information Do not operate this unit unless it is completely assembled. Do not block the ventilation filter. Do not directly view UV lights while in operation. Unplug unit before any cleaning or maintenance. This unit is not intended for outdoor use. Table of Contents Important Safety Information . . . . . 2 Operation . . . . . . . . . . . . . . . . . . . . . . 8-9 Product Contents . . . . . . .
Contents / Initial Setup • Active HEPA+ Unit • Unit Storage Bag • Power Cord • Owner’s Manual • Quickstart Guide Initial Setup • Remove your unit from the packaging. (Keep your bag and included materials) • Open the unit and take the filter out of the protective wrap and place the filter back into the unit before operation. • Install the Power Cord into the plug on the bottom of the unit, under the sliding panel. • Locate a suitable location to place your unit.
Diagrams NOTE: All diagrams shown are of the Active HEPA+ Room, but also apply to the Active HEPA+ Pro.
Diagrams Control Panel BPI Module (Brush Plugs) Fan Motor Housing HEPA Filter PCO Cell 5
Controls WiFi Status Indicator Component Status GOOD Display Active Display Information Information Unit Power Environment & Components Fan Speed Manual Mode 6 Auto Mode Night Mode
Greentech Connect Active HEPA+ can be controlled with the unit’s control panel as well as with the mobile application, Greentech Connect. • Scan this QR Code to download from your app store. • Create your account. • Make sure your Bluetooth is turned on to communicate with the unit. • Phone must be connected to the 2.4Ghz Wifi (the unit will not connect to a 5.0Ghz WiFi). • Set your unit in WiFi discovery mode by holding the Power Button down until the WiFi symbol begins to blink.
Operation Unit Power Press the Power Button to turn the unit ON or OFF. Fan Speed (Manual Mode) Press the Fan Speed Button (FAN) to cycle through the 5 fan speeds (Low, Med-Low, Medium, Med-High, High). Auto Mode Press the Auto Mode Button (AUTO) to put the unit into Auto Mode. During Auto Mode your unit will adjust fan speed based upon the air quality while showing a notification of the current air quality level.
Operation Night Mode - Dims all lights (Control Panel, Air Quality LED, PCO UV LEDS) First, choose your preferred purification mode/fan speed. Press the Night Mode button to turn Night Mode ON. Press any button to “wake” the unit up before the set 8 hour Night Mode period ends. Note: Using Night Mode will turn the PCO Cell’s UV Light OFF, temporarily reducing the unit’s purifying power until you exit Night Mode. Note: Night Mode time settings can be adjusted in the mobile app, Greentech Connect.
Cleaning & Maintenance WARNING: UNPLUG UNIT BEFORE CLEANING OR MAINTENANCE Cleaning For proper operation, the unit should be cleaned once a month. Note: For medical facilities, use CaviWipes™or any similar type of disinfecting wipe to clean the exterior of the unit.
Part Replacement - HEPA Filter with ODOGard® Coating Additional Filters, PCO Cells, and BPI Modules can be purchased through Greentech Environmental or a Greentech Environmental retailer. (1) Remove the top. (2) Remove filter. (3) Replace with new filter. (4) Replace top. 1 2 3 4 (5) Reset the Filter Life by navigating the information menu to the Filter Life screen and holding the information button until the life remaining changes to 100%.
Part Replacement - PCO Cell (1) Remove the top. (2) Pull the PCO Cell straight up to remove it from the internal post. (3) Replace with the new cell by aligning the keys on the cell and post then slide it down until fully seated. (4) Replace the top. 1 2 3 4 (5) Reset the PCO Cell Life by navigating the information menu on the control panel to the PCO Cell Life screen and holding the information button until the life remaining changes to 100%.
Part Replacement - BPI Module Brushes (1) Remove the two screws located on the inner/top edge of the rear handle. (2) Remove the handle cover. (3) Remove the two BPI Brush Plugs by grabbing the tabs and lifting them up and out. (4) Replace with the new BPI Brush Plugs by inserting them into their color-coordinated outlets until they are fully seated. (5) Replace the handle cover and screws.
Specifications Active HEPA+ ROOM Active HEPA+ PRO · Model: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1X5825 · Model: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1X5826 · Unit Dimensions: . . . . . . . . . . . . . . . . . . . . 10.6” * 10.6” * 17.5” · Unit Dimensions: . . . . . . . . . . . . . . . . . . . . . . 11.3” * 11.3” * 24.0” . . . . . . . . . . . . . . . . . . . . . . . . . 26.9cm * 26.9cm * 44.5cm . . . . . .
Warranty Information Your Active HEPA+ is warranted to be free from all defects in material and workmanship in normal household use for a period of 3 years from date of purchase. The warranty is granted only to the original purchaser and members of his or her immediate household. The warranty is subject to the following provisions: Any damages or malfunctions caused by negligence, abuse, or use not in accordance with the Owner’s Manual are not covered by this warranty.
www.GreenTechEnv.
