Manual
Table Of Contents
- 1 Description
- 2 General power tool safety warnings
- 3 Safety instructions for chain saws
- 4 Symbols on the product
- 5 Risk levels
- 6 Environmentally safe battery disposal
- 7 Proposition 65
- 8 Installation
- 9 Operation
- 10 Maintenance
- 11 Transportation and storage
- 12 Troubleshooting
- 13 Technical data
- 14 Limited warranty
- 15 Exploded view
- 1 Description
- 2 Avertissements généraux de sécurité des outils électriques
- 3 Instructions de sécurité concernant les scies à chaîne
- 4 Symboles figurant sur la machine
- 5 Niveaux de risques
- 6 Élimination des batteries sans danger pour l'environnement
- 7 Proposition 65
- 8 Installation
- 9 Utilisation
- 10 Entretien
- 11 Transport et entreposage
- 12 Dépannage
- 13 Données techniques
- 14 Garantie limitée
- 15 Vue éclatée
- 1 Descripción
- 2 Advertencias generales de seguridad para herramientas eléctricas
- 3 Instrucciones de seguridad para motosierras
- 4 Símbolos en el producto
- 5 Niveles de riesgo
- 6 Eliminación de batería segura para el medio ambiente
- 7 Propuesta 65
- 8 Instalación
- 9 Funcionamiento
- 10 Mantenimiento
- 11 Transporte y almacenamiento
- 12 Solución de problemas
- 13 Datos técnicos
- 14 Garantía limitada
- 15 Vista despiezada
WARNING
• If the battery pack or charger is damaged, replace the
battery pack or the charger.
• Stop the machine and wait until the motor stops before
you install or remove the battery pack.
• Read and understand the instructions in the battery and
charger manual.
NOTE
Optimize the power and performance of your new 2x24
machine by running with both batteries charged to 100%.
1. Align the lift ribs on the battery pack with the grooves in
the battery compartment.
2. Push the battery pack into the battery compartment until
the battery pack locks into place.
3. When you hear a click, the battery pack is installed.
8.4 REMOVE THE BATTERY PACK
1. Push and hold the battery release button (18).
2. Remove the battery pack from the machine.
9 OPERATION
NOTE
Remove the battery pack and keep hands clear of the lock
out button when you move the machine.
IMPORTANT
Examine the chain tension before each use.
9.1 EXAMINE THE CHAIN OIL
NOTE
Do not use the machine without sufficient chain oil.
1. Examine the oil level of the machine from the oil
indicator.
2. Add oil if necessary.
9.2 HOLD THE MACHINE
1. The grip area is within 100 mm behind the lock out
button.
2. Hold the chainsaw with your right hand on the rear
handle and left hand on the front handle.
3. Hold the handles with the thumbs and the fingers around
them.
4. Make sure that your left hand holds the front handle and
your thumb is below the handle.
9.3 START THE MACHINE
4
5
1. Press the lock-out button (4).
2. Press the trigger (5) while you hold the lock-out button.
3. Release the lock-out button.
IMPORTANT
The chain brake must be disengaged for the chain saw to
start. Activate the brake by moving the front hand guard
forwards.
9.4 STOP THE MACHINE
1. Release the trigger to stop the machine.
9.5 OPERATE THE CHAIN BRAKE
WARNING
Make sure that your hands are on the handles at all times.
1. Start the machine.
2. Push the guard forward to engage the chain brake.
3. Pull the handle guard / chain brake backwards to
disengage the chain brake.
4. Call approved service center for repair before use if
• The chain brake does not stop the chain immediately.
• The chain brake does not stay in the disengaged
position without aid.
9
English
EN