Electric Snow Thrower 2600202 Owner’s Manual TOLL-FREE HELPLINE: 1-888-90WORKS (888.909.6757) www.GreenWorksTools.com Read all safety rules and instructions carefully before operating this tool.
CONTENTS Contents .............................................................................................................................. 2 .......................................................................................................... 2 Safety information .............................................................................................................3-5 Symbols ................................................................................................
SAFETY INFORMATION FOLLOW THESE RULES WHILE OPERATING THE SNOW THROWER I M P O R TA N T READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below Walk. Do not run. Verify that the snow thrower is not in contact with anything before turning it on. Stay away from the discharge chute and impeller openings at all times. Keep face, hands, and feet away from concealed, moving, or rotating parts.
SAFETY INFORMATION Keep the impeller clear of debris. Do not attempt to clear the impeller while the motor is running or while the snow thrower is plugged in it. Turn the motor off and unplug the snow thrower from the extension cord or the outlet. Keep clothing and body parts away from the impeller. Stop the motor when stopped or when moving from one location to another. Unplug the snow thrower when it is being transported and when it is not in use.
SAFETY INFORMATION WA R N I N G ( P R O P O S I T I O N 6 5 ) Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL DESIGNATION/EXPLANATION V Voltage A Current Hz Frequency (cycles per second) min Time Double-insulated construction AC Alternating current RPM Revolutions per minute cm Centimeter Kg Kilogram /min Revolutions, strokes, surface speed, orbits etc.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product.
ELECTRICAL DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. WA R N I N G The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal insulation.
ELECTRICAL WA R N I N G Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools, or other obstructions while you are working with a power tool. Failure to do so can Inspect the extension cord and the power cord on a regular basis. Look for deterioration, cuts, or cracks in the insulation. Inspect the connections for damage. Repair or replace the extension cord or the power cord if any damage is found.
KNOW YOUR SNOW THROWER Read this operator's manual and safety rules before operating your snow thrower.
ASSEMBLY INSTRUCTIONS UNPACKING Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included. Inspect the product carefully to make sure no breakage or damage occurred during shipping. Do not discard the packing material until you have carefully inspected and satisfactorily operated the product. If any parts are damaged or missing, please call 1-888-909-6757 for assistance.
ASSEMBLY INSTRUCTIONS WA R N I N G Do not allow familiarity with this product to make you careless. Remember that a careless | WA R N I N G Do not use any attachments or accessories not recommended by the manufacturer of this product. = ASSEMBLING THE HANDLE ! $# Align the holes (4) on the middle handle (2) and the lower handle (3).
ASSEMBLY INSTRUCTIONS ASSEMBLING THE DISCHARGE CHUTE ! -# | ~{ + ~ the posts (4) on either side click into the keyed holes (5). ~ 1 3 5 2 3 5 2 4 4 Fig.
ASSEMBLY INSTRUCTIONS INSTALLING THE CHUTE CONTROL ROD ! ./0# Position the discharge chute (1) so that it faces forward. %&'() 1# .# Align the holes (3) on the upper chute control rod (4) with the holes on the lower chute control rod (5). Insert the hitch pin (6). Insert the end of the chute control rod (7) through the keyed hole (8) in the bracket that is attached to the top of the middle handle. (Fig.
ASSEMBLY INSTRUCTIONS Rotate the handle on the chute control rod to ensure that it moves in the same direction as the chute. (Fig. 8) 9 10 Fig. 7 Fig.
OPERATING INSTRUCTIONS STARTING THE SNOW THROWER WA R N I N G Avoid accidental start-ups. Verify that the operator is in the starting position when using the snow $ ; + + starting the snow thrower. POWERING ON AND OFF ! = 2# + ~{ While pressing the safety switch button with one hand, use your other hand to simultaneouly pull the bail switch (2) toward you.
OPERATING INSTRUCTIONS USING THE CORD RETAINER ! "3# This snow thrower is equipped with a cord retainer (1) in order to prevent the extension cord from disconnecting from the power cord while the snow thrower is in use. The cord retainer hangs from the cord guide bar. %&'() , 4 To use the cord retainer: Fold the extension cord to form a tight loop near the retainer.
OPERATING INSTRUCTIONS ADJUSTING THE DISCHARGE CHUTE AND CHUTE DEFLECTOR ! ""# WA R N I N G $ + + | + | = + = ~{ that you wish to direct the snow stream.
OPERATING INSTRUCTIONS UTILIZING THE LED LIGHTS ! "1# To utilize the LED lights (1) for night time snow removal, activate the LED light switch (2) . %&'() 2 1 Fig.
OPERATING INSTRUCTIONS OPERATING TIPS WA R N I N G $ + + + + = + ! + + + + impeller. Keep children and pets away from the operating area. ! + + can throw. Such items may be covered by a snowfall and go unnoticed.
MAINTENANCE SERVICING X ; + + @ thrower must be identical to the parts that they replace. If repairs are necessary, contact the Toll-Free Helpline, at 1-888-909-6757.
MAINTENANCE REPLACING THE DRIVE BELT ! "-# Ensure that snow thrower is not plugged in. Remove the 5 screws (1) that secure the left side plate (2) to the frame of the snow thrower. Remove the side cover. Remove the old belt (3) from the small pulley (5) and large pulley (4). Loop one end of the new belt over the small pulley. Rotate the impeller with the left hand while positioning the belt on the large pulley with the right hand.
MAINTENANCE REPLACING THE IMPELLER ! ".# Remove the 5 screws (1) that secure the right side cover (2) to the frame of the snow thrower. Remove the nut (3). Remove the 5 screws (4) that secure the left side cover (5) to the frame of the snow thrower. Remove the belt (6). Using a socket wrench, remove the the large pulley (7). Remove the 5 screws (8) that secure the left side plate (9) and remove the left side plate. Pull the axle (10) and remove the old impeller (11).
MAINTENANCE STORAGE Run the snow thrower for a few minutes in order to melt any snow that may be left on the snow thrower. Wipe the snow thrower off with a dry cloth before storage. This will help prevent ice building up on the unit and parts freezing. Disconnect the extension cord from the snow thrower. Inspect the extension cord thoroughly for signs of wear or damage. Replace it if it is worn or damaged. Inspect the snow thrower thoroughly for worn, loose, or damaged parts.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Then handle is not in position. The bolts are not properly seated. Make sure the bolts are correctly installed through the handle bars. Check to see if the hand knobs are tight. Refer to Assembling the Handle section in this manual. The Snow Thrower does not start. The switch is defective. Have the switch replaced by an authorized service center. The extension cord is not connected to the plug.
LIMITED FOUR-YEAR WARRANTY GREENWORKS™ hereby warranties this product, to the original purchaser with proof of purchase, for a period of four (4) years against defects in materials, parts or workmanship. GREENWORKS™, at its own discretion will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer.
EXPLODED VIEW / PARTS LIST ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 PART NO.
EXPLODED VIEW / PARTS LIST ITEM NO. 6 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 { 6-13 6-14 6-15 6-16 6-17 6-18 6-19 6-20 PART NO.
EXPLODED VIEW / PARTS LIST ITEM NO. 28 28-1 28-2 28-3 28-4 28-5 28-7 28-8 28-9 28-10 28-11 28-12 28-13 28-14 28-15 28-16 28-17 28-18 PART NO.
TOLL-FREE HELPLINE: 1-888-90WORKS (888.909.
