User manual

ManualsBrandsGREISINGER ManualsEnvironmental Testing EquipmentT-Log 100 Temperature Data Logger

E39.0.0X.6C-03

GREISINGER electronic GmbH

D - 93128 Regenstauf, Hans-Sachs-Straße 26

℡

℡℡

℡ +49 (0) 9402 / 9383-0  +49 (0) 9402 / 9383-33 | info@greisinger.de

Data logger for temperature

as of version V1.3 Operating Manual T-Logg 100

T-Logg 100

T-Logg 100 E

Summary of content (6 pages)

PAGE 1
E39.0.0X.6C-03 Data logger for as of version V1.3 Operating Manual temperature T-Logg 100 T-Logg 100 T-Logg 100 E GREISINGER electronic GmbH D - 93128 Regenstauf, Hans-Sachs-Straße 26 ℡ +49 (0) 9402 / 9383-0 +49 (0) 9402 / 9383-33 | info@greisinger.
PAGE 2
E39.0.0X.6C-03 1 Operating instruction T-Logg 100 and T-Logg 100 E page 2 of 6 General The logger T-Logg 100 and T-Logg 100 E are designed as a cost-efficient solution for monitoring temperatures. It enables an individual programming of the recording time. The last 16,000 measuring values can be stored in the memory. In addition, the LCD-display indicates both the temperature measured at the moment and the operating status of the logger.
PAGE 3
E39.0.0X.6C-03 4 Operating instruction T-Logg 100 and T-Logg 100 E page 3 of 6 Connection ■ Assignment of the input jack (front view to the pins): Interface [–] Not connected Interface [+] 5 Advice regarding state of logger upon delivery: Upon its delivery the logger is in a kind of 'sleeping state': The display does not show anything, the power consumption is at its minimum. The T-Logg 100 ‘wakes up’ as a communication link with a software has been established.
PAGE 4
E39.0.0X.6C-03 Operating instruction T-Logg 100 and T-Logg 100 E page 4 of 6 BATTERY: • Changing display BAT / Value: The battery of the T-Logg is getting discharged soon. Replace the battery briefly. Even so data logging is still active. • Constant display BAT: The Logger battery is empty now and data logging has been stopped. Replace the battery immediately. ALARM LOW: The temperature measured is below the min. alarm limit. ALARM HIGH: The temperature measured has exceeded the max. alarm limit.
PAGE 5
E39.0.0X.6C-03 8 Operating instruction T-Logg 100 and T-Logg 100 E page 5 of 6 Battery replacement Notice: As soon as BAT appears at display, the battery needs to be replaced. If battery voltage power decreases continuously, data logging will be stopped (compare with operating status ‘HALT’). Available stored data remains in the memory and do not get lost. It’s possible to read the measuring data after replacement of the battery. Replacement: 1.
PAGE 6
E39.0.0X.6C-03 9 Operating instruction T-Logg 100 and T-Logg 100 E page 6 of 6 Specification T-Logg 100 T-Logg 100 E Measuring range: -25.0 … +60.0 °C -25.0 ... +120.0 °C Resolution: 0.1°C (display and memory) 0.1°C (display and memory) Accuracy: (at nominal temperature) < ± 0.5 °C < ± 0.2 % of meas. value ± 0.5 °C Sensor: Integrated in device sensor tube made of stainless steel, Ø 5 mm, approx. 50 mm long, approx. 1 m silicone cable with anti-bucking glanding to housing.