Caution: You must read this before you proceed Bar Table Label Picture Description QTY A Table Top 1 B Left Pannel 1 C Right Pannel 1 1 D Left Back Pannel 1 E Left Pannel Right Back Pannel 1 F Middle Pannel 1 G Bottom Panel 1 Description Bolt(M6*35mm) QTY 23 ② Washer 23 ③ Allen Key 1 Label ① Picture 1 OF 4
Before Beginning Assembly: Overview Table Top(A) Left Back Pannel(D) Right Back Pannel(E) Right Pannel(C) Middle Pannel(F) Left Pannel(B) Bottom Panel(G) FRONT FACING This Bar Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Bar Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 E D Open the carton and place all the parts onto a clean, non-marring surface. Attach Left Back Pannel (D)to Right Back Pannel (E) using Bolts(①) and Washers(②) with Allen Key(③) as the picture show. DO not fully tigthen the Bolts. ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting positions preventing easy assembly. The PE wicker should never be cut, but moved away from the mounting positions.
Step 4 C Attach Table Top (A)&Left Panel( B)and Right Panel (C)using Bolts(①) and Washers(②) with Allen Key(③)as the picture show. DO not fully tigthen the Bolts. Step 5 Stand the Table up and check for stability. Then proceed to tighten all Bolts at all joints. Note: DO NOT fully tighten a BOLT in one go and then move on to the next. Rather, in asequential manner, gradually tighten each Bolt until all bolts are evenly secured.
Do not put hot items directly on furniture surface Do not clean furniture with harsh cleansers or polish. To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct sunlight is recommended. Children should not climb or jump on the furniture. Do not write on furniture without a padded barrier to protect the surface. To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine.
Caution: You must read this before you proceed Barstool Label Description QTY A Seat 1 B Leg 1 C Leg 1 D Footrest 2 Description QTY ① Bolt(M6*15mm) 13 ② Washer 13 ③ Allen Key 1 Label Picture Picture 1 OF 4
Before Beginning Assembly: Overview Seat(A) Leg(B) Leg(C) Footrest(D) FRONT FACING This Barstool has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Barstool parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean, non-marring surface. Attach Footrests(D) to Leg(C) using Bolts(①) and Washers(②) with Allen Key(③) as shown in the picture. Do not fully tighten the Bolts. Step 2 Attach Leg(B) to Footrests(D) using Bolts(①) and Washers(②) with Allen Key(③). Do not fully tighten the Bolts. Step 3 Attach Seat(A) to Leg(B) and Leg(C) using Bolts(①) and Washers(②) with Allen Key(③) as the shown above. Do not fully tighten the Bolts.
Step 4 Place the Barstool on a LEVEL SURFACE to check for wobbles. If it wobbles, lift the Barstool some 30cm to 50 cm high from the ground. Keep your feet and toes well away from the drop zone. Drop the Barstool freely and vertically with all four legs, hitting the ground, all at the same time. This Drop Test will help to ensure that all the Bolts and gaps reach full alignment status. Test again for evenness on a LEVEL SURFACE. If no wobbles are found, slowly and steadily, place the Barstool facedown.
Do not put hot items directly on furniture surface Do not clean furniture with harsh cleansers or polish. To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct sunlight is recommended. Children should not climb or jump on the furniture. Do not write on furniture without a padded barrier to protect the surface. To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine.
