Our best compliments for choosing Grimac quality
O PERATING INSTRUCTI O NS CE Declarat i o n o f C o n f o r m i t y We: Grimac s.r.l.
I ndex 0 - INTRODUCTION 0.1 - Foreword 0.2 - Symbols 0.3 - Basic safety warnings 0.4 - Protection covers 0.5 - Safety precautions to follow when repairing or servicing the coffee maker 0.6 - Practical tips for brewing a quality cup of coffee pg. 19 19 20 20 21 21 1 - T E C H N I C A L D E TA I L S 1.1 - General information 1.2 - Receiving the coffee maker and unpacking 1.3 - Positioning and installation 1.4 - Technical specifications 1.5 - Guarantee 22 22 22 23 23 2 - GENERAL DESCRIPTION 2.
C hapter 0 - I n t r o d u c t i o n 0.1 - FOREWORD These OPERATING INSTRUCTIONS are a guide to using and maintaining the GRIMAC TERRY TECH pod coffee maker. Before USING OR SERVICING the coffee maker, read this MANUAL carefully and thoroughly. This manual provides information, advice and precautions about how to use the TERRY TECH pod coffee maker to ensure longevity and perfect performance in time. It is very simple to use and brews a cup of excellent coffee in just a few seconds.
Chapter 0 - I n t r o d u c t i o n 0 . 3 - B A S I C S A F E T Y WA R N I N G S • The TERRY TECH pod coffee maker is designed for the specific purpose described herein and any other use or the use of other products which were not approved at the time of purchase of this coffee maker, GRIMAC srl shall not be held responsible nor liable for injury to persons, animals or damage to things caused by an incorrect or improper use. THE PREMISES WIRING SYSTEM MUST BE EARTHED.
C hapter 0 - I n t r o d u c t i o n 0.5 - SAFETY PRECAUTIONS TO FOLLOW WHEN R E PA I R I N G O R S E R V I C I N G T H E C O F F E E M A K E R • Switch off the coffee maker and disconnect the plug at the mains socket-outlet before performing routine maintenance, repair work or cleaning. • To extend the service life and performance of your coffee maker, parts must be replaced only with original spares and by qualified personnel.
C hapter 1 - Te c h n i c a l d e t a i l s 1 . 1 - G E N E R A L I N F O R M AT I O N All machine components and materials used in manufacturing this pod coffee marker all conform to the new standards in force. The TERRY TECH pod coffee maker has been designed and developed with meticulous care above all to wiring, electrics and parts which come into direct contact with the coffee. 1 .
C hapter 1 - Te c h n i c a l d e t a i l s The coffee maker is sold pre-assembled and ready for use and does not require additional installation work. Simply plug it into the mains socket-outlet. Before using the coffee maker for the first time, rinse the water tank. To remove the tank disconnect the two tubes and remove from its compartment. Rinse and then fill with water, replace and reconnect the two tubes previously disconnected in their respective holes (fig. 6).
C hapter 2 - G e n e r a l d e s c r i p t i o n 2.
C hapter 3 - U s i n g t h e c o f f e e m a k e r 3.1 - CONTROLS AND CONTROL FUNCTIONS N.B. when dispensing hot water or steam position the lever as illustrated in fig.1 this is to prevent the two halves of the pod holder - top and bottom - from closing together. WARNING: hot water and steam are dispensed at a high temperature. Hazard of scalding. • Lever: by moving this lever to the right the bottom half of the pod holder locks together with the top half. 3 .
C hapter 3 - U s i n g t h e c o f f e e m a k e r • Insert a coffee pod in the pod holder and make sure its sits evenly. • Push the lever to the right to close pod holder (fig. 4). • Place a cup under the brewing spout and press either the single or double serving button to dispense coffee (fig. 4). • Dispensing will stop automatically. • Push the lever to the left to open the pod holder, remove and throw away the used pod (fig. 3) and then close the pod holder by pushing the lever to the right.
C hapter 4 - Tr o u b l e s h o o t i n g a n d r e m e d i e s 4.2 - GENERAL CHECKS POWER CABLE (230V GG 3060 - 110V GG 3057) Check the power cable regularly and replace if it is worn or damaged. WATER TANK Check water level occasionally utilising the inspection slot located on the left and top up if necessary. To top up remove the metal tank lid and fill with water as illustrated in fig. 6. Do not use the coffee maker without water in the tank. C hapter 5 - M a i n t e n a n c e 5.
Chapter 5 - Ma i n t e n a n c e - Approx. every 300 coffees, clean the filter by submersing it in a water and salt solution (regeneration). Filter life depends on the hardness of the water. - After approx. 10-12 months replace with a new filter. EXTERNAL HOUSING: to keep external housing clean, use a sponge or cloth soaked with a cleaning product - neutral detergent. Do not use solvents, abrasive powders, or scouring pads to clean. 5.
C hapter 5 - M a i n t e n a n c e 5.3 - CHANGING COFFEE BREWING TIME, T E M P E R AT U R E A N D L A N G U A G E S E T T I N G S Standard model: By following these simple steps, it is possible to modify single or double coffee brewing times: • Turn the coffee maker off at the main ON/OFF switch; • Press the single serving button and turn on the coffee maker simultaneously (pos.
Chapter 5 - Ma i n t e n a n c e • At this point the prompt “SINGLE SERVING TIME” will come up on the display: use buttons 1 and 2 to modify settings and utilising button 3 confirm desired brewing time. Repeat these steps for modifying brewing time settings for double serving and water; • Once having modified and confirmed new settings, remove the chip card and use the coffee maker as normal. N.B. Only change settings with the coffee maker in temperature.
4 5 6 7 6 5 3 8 4 8 9 6 7 31 ENGLISH 5