Coffee Grinder User Manual

ManualsBrandsGrindmaster ManualsCoffee Grinder865

Grindmaster Corporation

800 Series Coffee Grinders

Operation and Instruction Manual

for

Models 810, 835, 865, 875 and 890

Table of Contents

Installation ....................................................3

Operating Instructions ..................................3

Grind Adjustment ..........................................4

Shear Disc Replacement ..........................4-5

Cleaning Instructions ....................................5

Lubrication ....................................................5

Troubleshooting Guide ................................6

Exploded View ..........................................7-9

Wiring Diagrams ........................................10

Grindmaster Corporation

4003 Collins Lane

Louisville, Kentucky 40245 USA

(800) 695-4500 (USA & Canada only)

(502) 425-4776

FAX: (502) 425-4664

www.grindmaster.com

PRINTED IN USA

0509 Form # GR-380-16

Part# 83427

Prior authorization must be obtained

from Grindmaster Corporation for

all warranty claims.

Model 890

Summary of content (12 pages)

PAGE 1
Grindmaster Corporation 800 Series Coffee Grinders Operation and Instruction Manual for Models 810, 835, 865, 875 and 890 Table of Contents Installation ....................................................3 Operating Instructions ..................................3 Grind Adjustment ..........................................4 Shear Disc Replacement ..........................4-5 Cleaning Instructions ....................................5 Lubrication ....................................................
PAGE 2
PAGE 3
Installation Instructions 1. 2. 3. 4. 5. 6. 7. Please read this manual before operating the grinder. Carefully remove grinder from carton. Place grinder in position on shelf, counter or other flat surface. Plug grinder into standard electric outlet. Avoid using an extension cord. Grind a small amount of whole bean coffee following operating instructions as described in this manual. If there is any problem, consult the Troubleshooting Guide in this manual, (also on back of grinder.
PAGE 4
Protection The grinder is equipped with both a circuit breaker and a shear disc release to protect the motor and burrs if a foreign object, such as a nail or rock, gets into the coffee. Grind Adjustment Tools required: Large blade and medium Phillips head screwdrivers In order to adjust the grind, follow these steps (Refer to figure A): 1. Remove all coffee from the hopper. 2. Set selector knob to the finest setting (Espresso or Turkish) depending on the model. 3.
PAGE 5
FEEDWORM & ROTARY BURR GRIND CAP (ASSEMBLED) SHEAR DRIVE GRIND HEAD DWG NO.: 83457 REVISION: REL SHEAR DISC SHEAR COVER SCREW, 5/16 X 1” LG Model 865/890 GRIND GRIND HEAD HEAD FEEDWORM ROTARYBURR BURR FEEDWORM &&ROTARY GRIND CAP (ASSEMBLED) GRIND CAP (ASSEMBLED) ROLL PIN ROLL PIN SHEAR COVER SHEAR COVER SCREW, 5/16-18 SCREW, 5/16-18XX1"LG 1” LG Figure B ROLL PIN REPLACEMENT FIGURE : B Cleaning Instructions The outside of machine can be cleaned with a damp cloth or common household polishing wax.
PAGE 6
Troubleshooting Guide The following procedures must be performed by a qualified service technician. PROBLEM Grinder will not start when START button is pushed. Grinder runs or hums but no coffee is dispensed. Excessive amount of chaff flying about. POSSIBLE CAUSE SOLUTION • Bag not under spout. • Place bag underneath spout. • Plug not in outlet properly. • Install plug in outlet. • No power to outlet. • Check outlet with lamp or radio to verify outlet has power.
PAGE 7
800 Series Exploded View 3$57 180%(56 ,1',&$7(' %< $1 $67(5,6.
PAGE 8
00 Series Parts List - 120V ITEM # 2 *3 *4 5 *6 *7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 *25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 53 *54 55 56 57 *58 59 60 *61 62 64 68 66 67 75 76 78 79 80 81 82 83 84 79 88 89 DESCRIPTION Washer, #8 internal tooth Top,800 series sanitation * Lid, 800 series sanitation * Screw, #8 x 1/4 ph truss hd Lid, bifold hinge * Top, bifold lid * Hopper Finger guard Gasket, hopper Screw, # 8-32 x 3/8"slotted ovl Plate, knob retainer K
PAGE 9
800 Series Parts List - 230V ITEM # 2 *3 *4 5 *6 *7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 *25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 50 51 52 53 *54 55 56 57 *58 59 60 *61 62 64 68 66 67 75 76 78 79 80 81 82 83 84 79 88 89 DESCRIPTION Washer, #8 internal tooth Top,800 series sanitation * Lid, 800 series sanitation * Screw, #8 x 1/4 ph truss hd Lid, bifold hinge * Top, bifold lid * Hopper Finger guard Gasket, hopper Screw, # 8-32 x 3/8"slotted ovl Plate, knob retaine
PAGE 10
Wiring Diagrams for 120 Volt 60Hz Units Page 10 800 Series Coffee Grinders
PAGE 11
PAGE 12
Grindmaster® Coffee Grinders and Brewers • PrecisionBrew™ Brewing Systems • Espressimo® Espresso Machines Crathco® Hot Beverage Dispensers • Crathco® Cold and Frozen Beverage Dispensers • AMW Coffee and Tea Systems Tel (502) 425-4776 • Fax (502) 425-4664 • 1-800-695-4500 (USA & Canada only) P.O. Box 35020 • Louisville, KY 40232 • USA www.grindmaster.com • email: info@grindmaster.