Instructions / Assembly

ManualsBrandsGrisham ManualsDoors & Windows36 in. x 80 in. 105 Series Black Hinge Right Van Gogh Security Door with Self-Storing Glass Feature

TOOLS REQUIRED:

• Electric Drill

• Hammer

• Hack Saw

• 3/8" Wood Chisel

• 5/32" Drill Bit

• Phillips Head Screw Driver

• Flat Head Screw Driver

For Questions Concerning This Product

Phone - 1-800-238-1005

MAINTENANCE GUIDE

FINISH

LOCK MECHANISM

GLASS CLIPS

PARTS

CLOSER

Grisham Bros.

SCREEN PANEL

TEMPERED

GLASS PANEL

HINGE SIDE Z-BAR

STORM CHAIN

RAIN CAP

HEADER

LATCH SIDE Z-BAR

DEAD BOLT LOCK HANDLES

CLOSER

EXPANDER BAR

DOUBLE WEATHER

STRIPPED SWEEP

INSTALLATION, MAINTENANCE, & WARRANTY

Your steel security system storm door will look beautiful much longer by following these simple procedures. Once or twice a year, apply a coat of

Armor All or similar product to help retain the finish luster and protect against ultra-violet deterioration. All steel products exposed to weather can rust.

Periodically, inspect your door for scratches or abrasions on the painted surface. If any are found, s

and surface, if necessary, and touch up with paint

immediately.

Once or twice a year, you should lubricate the door’s locking mechanism. WD-40 , Graphite, or Teflon based lubricants are recommended, but most any

household lubricant will be helpful. Also, lubricate the hinges should a squeak develop.

Be sure that the glass panel clips are only hand tight. Over tightening can cause the glass clips to break. If any are loose, simply tighten with a Phillips

head screwdriver.

To keep all parts looking new, use any good cleaner. Frequency may depend on how severe the weather is in your area. A once a year cleaning and

polishing is sufficient in most areas. Also, check the handle to be sure the set screw is still tightly secured; if not, tighten it back down with a screw driver.

Check closer action about twice a year. Open the door a few times and let it close by itself so that you can see whether or not the closer tension should be

increased or decreased for smoothest operation. The adjustment screw is located at the end of the closer cylinder. Unscrew the adjustment screw to

decrease tension; screw it in more tightly to increase tension. To fine tune the adjustment screw, make adjustments in quarter-turns until you find the

optimum adjustment.

® ®

The welded frame, pickets and lock box of a Grisham Security door is warranted against breakage for as long as you own the home on which the

Grisham door has been installed. Should a weld break or structural defect exist, Grisham will repair or replace the door at our discretion. This

warranty does not cover damage caused by vandals, break-ins, or attempted break-ins.

Components that prove to be defective in material or workmanship are warranted for a period of 1-year. (Excluding Glass and Screen).

Your Grisham security door is warranted against paint defects and rust for a period of 1-year from the date of purchase. Rust and paint finish claims

may not be the result of abrasions, abuse, misuse, alterations, or negligence.

Warranty questions or claims. Please call 1-800-647-6736 7:00 to 3:30 pm CST. Thank You.

Limited Lifetime Warranty

Summary of content (8 pages)

PAGE 1
Grisham Bros.
PAGE 2
Installation Instructions: For NOTE: 300 Series Doors If necessary to reverse door hinging, please follow hinge side conversion instructions first. Reversible sizes: (30" 32" 34" and 36" x 80"). No Z-bar cuts can be made prior to hinge reversing process. Note: In some homes the door frame mounting surface may NOT be plumb and square, and may require the use of wood shims to build out, and equally an area may require the removal of surface material to properly complete the installation. 1.
PAGE 3
13. With the door open, fit the expander bar onto the bottom of the door. Close the door and position the expander bar so that the bar fits snugly against the threshold but does not restrict door operation. From inside the door, drill holes through the expander bar and secure the expander bar to the door with Phillips head screws provided. HINGE SIDE CONVERSION 1. Lay the door flat on saw horses or other flat surface, placing packing carton underneath the door to prevent scratching.
PAGE 4
LOCK GUARD INSTALLATION Screw Screw Position lock guard on latch side of door after lock is installed. The drilled tabs will fit right over the top and right under the bottom of the striker plate. Mark the door using the pre-drilled holes on the lockguard and using a 3/32 drill bit, drill the 2 holes. Install lock guard using #6, 3/4" self-tapping screws that are provided.
PAGE 5
Grisham Bros.
PAGE 6
Instrucciones de instalación: Las NOTA: puertas de la serie 300 Si es necesario invertir bisagras para puertas, siga las instrucciones de conversión lado de las bisagras. Reversible tamaño: (30" 32" 34" y 36" x 80"). No Z-bar se pueden realizar cortes antes de bisagra proceso de inversión.
PAGE 7
13. Con la puerta abierta, colocar el expansor barra en la parte inferior de la puerta. Cierre la puerta y colocar el expansor bar para que la barra se ajuste perfectamente en el umbral pero no restringir funcionamiento de puerta. Desde el interior de la puerta, perforar agujeros en el ampliador bar y bar el expansor de la puerta con los tornillos de cabeza Phillips. CONVERSIÓN DEL LADO DE BISAGRA 1.
PAGE 8
INSTALACIÓN DE LA PROTECCIÓN DE BLOQUEO Tornillo Tornillo Posición de bloqueo en el lado del pestillo de la puerta después del bloqueo está instalado. Las fichas perforadas, ajustarse a la derecha en la parte superior y a la derecha en la parte inferior de la placa del percutor. Marcar la puerta usando el los agujeros perforados en el lockguard 3/32 y el uso de un taladro con broca los 2 orificios. Instalar protección de cierre con #6, 3/4" tornillos autorroscantes que se prestan.